Page 3
CPE Side ............................46 CONFIGURATION VIA SERIAL CONSOLE OR TELNET ................ 47 ..........................47 NTRODUCTION 5.1.1 Serial Console ........................47 5.1.2 Telnet ............................. 47 ..........................48 AIN MENU CLI C ....................49 OMMAND TREE OVERVIEW Dynamix UM-S4FB Series rev.2 User Manual V0.06...
SOHO and SME users. UM-S4FB supports back to back connectivity for long reach Ethernet extension. Users can make a direct connection between two SHDSL.bis routers by using a standard telephone cable, and configure one as CO and the other as CPE.
EFM mode compliant to IEEE 802.3, PPP over Ethernet (RFC2516) Support of OAMPDU information and functionality ( ITU-T Y.1731) OAMPDU Event Notification, Variable Request, Variable Response, Loopback Control VLAN base QOS (802.1P/Q), Priority Queue Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Page 6
Physical / Electrical Dimensions: 18.7 x 3.3 x 14.5cm (WxHxD) Power: 100~240VAC (via power adapter) Power Consumption: 9 watts Max Operating Temperature: 0~45°C Storage Temperature: -20°C~70°C Humidity: 0%~95%RH (non-condensing) Dynamix UM-S4FB Series rev.2 User Manual V0.06...
VCCI EN60950 We reserves the right to change specifications without prior notice. Products’ Information UM-S4FB 2-Wire G.Shdsl.bis EFM Router with 4 LAN Port UM-S4FB/4w 4-Wire G.Shdsl.bis EFM Router with 4 LAN Ports Dynamix UM-S4FB Series rev.2 User Manual V0.06...
LINK/ACT4 Blink Transmit or received data over LAN 4 SHDSL.bis line connection is dropped Blink SHDSL.bis self-test No Alarm The rear panel of SHDSL.bis router is where all of the connections are made. Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Page 10
Internet and you want to configure it again by clearing all configurations, press the Reset Button for 4 seconds with a paper clip or sharp pencil. Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Below figure show the SHDSL.bis line cord plugs pin asignment: Below figure show the cosole cable pins asignment: Pin Number Description Figure No connection RxD (O) TxD (I) No connection No connection CTS (O) RTS (I) No connection Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Users need to know the Internet Protocol supplied by your Service Provider and determine the mode of setting. Protocol Selection RFC1483 Ethernet over ATM RFC1577 Classical Internet Protocol over ATM RFC2364 Point-to-Point Protocol over ATM RFC2516 Point-to-Point Protocol over Ethernet Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Page 13
Bridge EoA Route EoA VPI: VPI: VCI: VCI: Encapsulation: Encapsulation: Gateway: IP Address: Host Name:(if applicable) Subnet Mask: Gateway: DNS Server: PPPoE VPI: VCI: Encapsulation: User Name: Password: DNS Server: Host Name:(if applicable) Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Connect the phone cable to the router and the other side of phone cable to wall jack. Connect the power adapter to power source inlet. Turn on the PC or NB, which is used for configuration the Router. SHDSL.bis 4-ports router with complex network topology Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Note: After changing the User Name and Password, strongly recommend you to save them because another time when you login, the User Name and Password have to be used the new one you changed. Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Page 16
Virtual Server • DDNS • Firewall • Content Filter • IGMP • SNTP ADMIN • SECURITY • MGMT UTILITY • SYSTEM LOG • SYSTEM TOOL • UPGRADE • RESTART LOGOUT Dynamix UM-S4FB Series rev.2 User Manual V0.06...
After completing it successfully, you can access Internet or use a pair of Shdsl.bis Routers as LAN extenders. This is the easiest and quickest way to setup the router. Click BASIC for basic installation. G.SHDSL Item Description Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Page 18
Submask Enter a subnet mask in dotted decimal notation when select Static IP address Type. Gateway IP Address Enter a gateway IP address provided by your ISP when select Static IP address Type. Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Page 19
Enter User Name provided by the ISP for PPPoE Password Enter Password provided by the ISP for PPPoE Click on Apply to save the parameters or Cancel to start configuring this page from beginning. Dynamix UM-S4FB Series rev.2 User Manual V0.06...
LAN. Bridged connections do not use the IP protocol. EoA can also be configured to provide a routed connection with the ISP, which uses the IP protocol to exchange data. Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Page 21
Protocol (PPP), commonly used in dialup connections, with the Ethernet protocol or ATM protocol, which supports multiple users in a local area network. The PPP protocol information is encapsulated within an Ethernet frame or ATM frame. Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Current status of Network, DSL and Route Table. Packet Statistics System Status and Packet statistics for WAN port and LAN port. Mode, Line rate and Performance information including SNR margin, atteunation G.SHDSL and CRC error count. Dynamix UM-S4FB Series rev.2 User Manual V0.06...
MCSV, Software Version, Ethernet MAC Address, Serial Number, DSL Chip Name, DSL Hardware Pair Number, DSL Firmware Version, System Current Time and System Update Time. STATUS > Networking NETWORKING STATUS page displays Network Status, DSL Status and Route Table information Dynamix UM-S4FB Series rev.2 User Manual V0.06...
PACKET STATUS page displays System Status and packet statistics for WAN port and LAN port. STATUS > G.SHDSL G.SHDSL STATUS page displays current status of DSL line including Channel Name, State, Annex, TCLayer, Line Rate, SNR, Loop Attenuation, TxPower and CRC. Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Virtural Server, DDNS, Firewall, Content Filter, IGMP and SNTP. Note: The advanced functions are only for advanced users to setup advanced functions. The incorrect setting of advanced functions will affect the performance or result system error, even disconnection. ADVANCED>SHDSL.bis Dynamix UM-S4FB Series rev.2 User Manual V0.06...
For point to point applications, you may choose one of the four types according to which line rate you need. Modulation Select the modulation supported by your ISP. Click on Apply to save the parameters or Cancel to start configuring this page from beginning. ADVANCED>WAN Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Page 27
Gateway IP Address Enter a gateway IP address provided by your ISP when select Static IP address Type. Click on Apply to save the parameters or Cancel to start configuring this page from beginning. Dynamix UM-S4FB Series rev.2 User Manual V0.06...
User Defined: Select this option when you have the IP address of a DNS server. DNS Relay: Select this option when your ISP uses IPCP DNS server extensions and the SHDSL.bis Router acts as DNS proxy. Dynamix UM-S4FB Series rev.2 User Manual V0.06...
The table displays the list and status of clients with their Host Name, State, IP address, MAC and Expired Time. Static DHCP Item Description IP Address Enter IP address to change the static DHCP setting MAC Address Enter the MAC address of the Ethernet device. Static List Dynamix UM-S4FB Series rev.2 User Manual V0.06...
The router supports two types of VLAN: 802.1Q Tag-Based VLAN and Port-Based VLAN. VID: (Virtual LAN ID) It is an definite number of ID range from 1 to 4094. PVID: (Port VID) It is an untagged member from 1 to 4094 of default VLAN. ADVANCED>VLAN Dynamix UM-S4FB Series rev.2 User Manual V0.06...
This field is not effective when traffic matches the class configured under Precedence CLASS SETUP. When select ON and traffic doesn’t match the class configured under CLASS SETUP, the router assigns priority to unmatched traffic based on IEEE Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Page 32
Select Auto to map the DSCP value to 802.1 priority level automatically 802.1Q Tag Select Same to keep the priority setting and VLAN ID of the frames. Select Auto to map 802.1 priority level to the DSCP value automatically Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Off: No RIP packets will be sent, and incoming RIP packets will be ignored Both: Routing table will be broadcasted periodically and incorporated received information from both direction In Only: Only RIP information received will be incorporated Out Only: Only broadcast device’s routing table periodically Dynamix UM-S4FB Series rev.2 User Manual V0.06...
DMZ host’s security, the Web pages might be corrupted, but no other company information would be exposed. ADVANCED>NAT/DMZ NAT vs. DMZ Setup Item Description NAT/DMZ Mode Select to Enable or Disable NAT/DMZ mode Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Service with corresponded IP address and Port range. Server IP Address Specify the IP address of the Service’s Hosting Server Click on Apply to save the parameters or Cancel to start configuring this page from beginning. ADVANCED>DDNS Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Input the static IP address for the Host Name if IP Policy is selected with Specified IP Address option. Click on Apply to save the parameters or Cancel to start configuring this page from beginning. ADVANCED>FIREWALL Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Turning Off or On of the selected Filter condition Keyword Specify the desired keywords to be filtered with IGMP (Internet Group Multicast Protocol) is a network layer protocol which is used to establish membership in a Multicast group. ADVANCED>IGMP Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Time Zone Specify the Time zone Daylight Savings Check box to enable Daylight Savings function Start Date Specify the date when daylight saving starts End Date Specify the date when daylight saving ends Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Item Description System Name Enter desirable System/Host Name Domain Name Enter desirable Domain Name Authentication Timeout Enter desirable Authentication Timeout period in minutes Note: The character support [A-Z], [a-z], [0-9], [_(underline), -(dash), .(dot)] Dynamix UM-S4FB Series rev.2 User Manual V0.06...
The router can generate SNMP traps to indicate alarm conditions, and it relies on SNMP community strings to implement SNMP security. The SHDSL.bis routers support SNMPv1/SNMPv2 (RFC 1157/1901/1905) and MIB-II (RFC 1213/1493) Click SNMP to configure the parameters for remote management via SNMP. Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Access Status Click on the drop-down list and select ALL to allow the service or Disable WAN to disable the remote management service Click TELNET to configure the parameters for remote management via TELNET Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Default: The SSH allow accessible from LAN side only. Overview This section describes the utility of the SHDSL.bis router including: SYSTEM LOG Capturing log information Backup and restore configuration, and load the factory default SYSTEM TOOL configuration UPGRADE Upgrade the firmware Dynamix UM-S4FB Series rev.2 User Manual V0.06...
The router can generate a syslog message and send it to a syslog server. You may click Refresh to renew the Sytem Log page or Clear Log to delete all log information. SYSLOG Server Setting Item Description Active Activate the syslog server Dynamix UM-S4FB Series rev.2 User Manual V0.06...
To restore a previously saved config file from your computer. Click Browse to select the file and then click Upload. Click Reset to load factory default settings to the router. A warning message will appear. Confirm by clicking on OK. UTILITY>UPGRADE Dynamix UM-S4FB Series rev.2 User Manual V0.06...
UTILITY>RESTART Use RESTART to reboot the SHDSL.bis router. Click on Restart to reboot the system. Overview To logout the router, click on LOGOUT. A warning message will appear. Confirm by clicking on OK. Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Example Click Bridge and STU-C Side to setup Bridge mode of the Router Enter LAN Parameters IP: 192.168.0.1 Subnet Mask: 255.255.255.0 Gateway: 192.168.0.1 Enter WAN Parameters VPI: 0 VCI: 32 Click LLC Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Click Bridge and STU-C Side to setup Bridge mode of the Router Enter LAN Parameters IP: 192.168.0.2 Subnet Mask: 255.255.255.0 Gateway: 192.168.0.2 Enter WAN Parameters VPI: 0 VCI: 32 Click LLC Click Apply The router will reboot with the new setting. Dynamix UM-S4FB Series rev.2 User Manual V0.06...
LAN LNK LED indicator on the front panel shall light if a correct cable is used. Starting your Telnet client with VT100 terminal emulation and connecting to the management IP of Router, wait for the login prompt appears. Input User and Password after login screen pop up, Dynamix UM-S4FB Series rev.2 User Manual V0.06...
Reset and boot system. After you have completed all necessary setting, reboot make sure to apply the new configuration to NVRAM and reboot the system, otherwise, all of your changes will not take effect. quit Quit system. Dynamix UM-S4FB Series rev.2 User Manual V0.06...