The Dynamix UM-SB (Symmetric High Speed Digital Subscriber Loop) router (with ATM/EFM layer) comply with G.991.2(2004) standard optimized for small to medium size business environment. It provides business-class, multi-range from 192Kbps to 5.696Mbps (for 2-wire model) and 384Kbps to 11.392Mbps (for 4-wire model) symmetric payload rates over exiting copper wire.
User access control: deny certain access of PCs to Internet service (Firewall model) Management Easy-to-use web-based GUI for quick setup, configuration and management Menu-driven interface/Command-line interface (CLI) for local console and Telnet access Password protected management and access control list for administration Dynamix UM-SB Series User Manual V0.06...
Page 8
Data Rate: N x 64Kbps ,N=3~89 (for 2-wire model) Data Rate: N x 128kbps, N= 3~89 (for 4-wire model) Impedance: 135 ohms Virtual LAN 802.1Q Tag-Based VLAN Port Based VLAN Dynamix UM-SB Series User Manual V0.06...
Page 9
2MB Flash Memory, 8MB SDRAM Products’ Information UM-SB 2-wire router/bridge with 1-port LAN UM-SFB 2-wire router/bridge with 1-port LAN, VLAN and business class firewall UM-S4B 2-wire router/bridge with 4-ports switching hub LAN, VLAN UM-S4FB 2-wire router/bridge with 4-ports switching hub LAN, VLAN and business class firewall ...
Ethernet cable is connected to LAN 3 Blink Transmit or received data over LAN 3 Ethernet cable is connected to LAN 4 Blink Transmit or received data over LAN 4 SHDSL.bis line connection is dropped Blink SHDSL.bis self test Dynamix UM-SB Series User Manual V0.06...
Page 12
LAN port connect with 10M NIC 10M/ACT Blink LAN port acts in 10M LAN port connect with 100M NIC 100M/ACT Blink LAN port acts in 100M SHDSL.bis line connection is dropped Blink SHDSL.bis self test Dynamix UM-SB Series User Manual V0.06...
Internet and you want to configure it again clearing all configurations, press the Reset Button for four seconds with a paper clip or sharp pencil. Dynamix UM-SB Series User Manual V0.06...
Below figure show the SHDSL.bis line cord plugs pin asignment: Below figure show the cosole cable pins asignment: Pin Number Description Figure No connection RxD (O) TxD (I) No connection No connection CTS (O) RTS (I) No connection Dynamix UM-SB Series User Manual V0.06...
Users need to know the Internet Protocol supplied by your Service Provider and determine the mode of setting. Protocol Selection RFC1483 Ethernet over ATM RFC1577 Classical Internet Protocol over ATM RFC2364 Point-to-Point Protocol over ATM RFC2516 Point-to-Point Protocol over Ethernet Dynamix UM-SB Series User Manual V0.06...
Page 16
VPI: VPI: VCI: VCI: Encapsulation: Encapsulation: User Name: IP Address: Password: Subnet Mask: DNS Server: Gateway: Host Name: (if applicable) DNS Server: PPPoE VPI: VCI: Encapsulation: User Name: Password: DNS Server: Host Name:(if applicable) Dynamix UM-SB Series User Manual V0.06...
Page 17
Connect the phone cable to the router and the other side of phone cable to wall jack. Connect the power adapter to power source inlet. Turn on the PC or NB, which is used for configuration the Router. Dynamix UM-SB Series User Manual V0.06...
Page 18
Direct Connection with PC or NB for SHDSL.bis 1-port router Server File Server Workstation Mobile Device HUB/Switch Ethernet Cable Wireless LAN Power Adpater Wall Jack DB-9 Cable Connection with Hub/Switch for SHDSL.bis 1-port router SHDSL.bis 4-ports router with complex network topology Dynamix UM-SB Series User Manual V0.06...
Step. 1 Click the start button. Select setting and control panel. Step. 2 Double click the network icon. Dynamix UM-SB Series User Manual V0.06...
Page 20
In the Configuration window, select the TCP/IP protocol line that has been associated with your network card and then click property icon. Choose IP address tab. Select Obtain IP address automatically. Click OK button. Dynamix UM-SB Series User Manual V0.06...
Page 21
Note: After changing the User Name and Password, strongly recommend you to save them because another time when you login, the User Name and Password have to be used the new one you changed. Dynamix UM-SB Series User Manual V0.06...
Page 22
If the router is not the Firewall model, the menu will not display FIREWALL items. If the router is not the 4-wires model, the menu will not display the status of SHDSL.bis channel B. Dynamix UM-SB Series User Manual V0.06...
Click Basic for basic installation. Parameter Table: ⊠ System mode □Route Bridge SHDSL □CO side □CPE side □CO-CPE side IP address Subnet Mast Gateway Host Name WAN1 Encapsulation □VC-mux □LLC Dynamix UM-SB Series User Manual V0.06...
Page 24
For connection with DSLAM, the SHDSL.bis router’s working mode is CPE. For “LAN to LAN” connection, one side must be CO and the other side must be CPE. Set up (a) LAN IP address , Subnet Mask, Gateway and Host Name (b) WAN1 VPI,VCI and Encapsulation LAN: Dynamix UM-SB Series User Manual V0.06...
Page 25
The screen will prompt the new configured parameters. When using on bridge mode, the protocol mode must be automatic set to Ethernet over ATM (EoA).Checking the parameters and Click Restart .The router will reboot with the new setting or Continue to configure another parameters. Dynamix UM-SB Series User Manual V0.06...
DNS Server 2 DNS Server 3 Lease time MAC : DHCP Server MAC : MAC : MAC : MAC : Host Entries MAC : MAC : MAC : MAC : MAC : DHCP Relay IP address Dynamix UM-SB Series User Manual V0.06...
Page 27
Setup up system mode and SHDSL mode click ROUTE and CPE Side then press Next. Set up the LAN IP address , Subnet Mask, Gateway, Host Name and Trigger DHCP Service with fixed IP type. Dynamix UM-SB Series User Manual V0.06...
Page 28
If the DHCP server is “Enable,” you have to setup the following parameters for processing it as DHCP server. The embedded DHCP server assigns network configuration information at most 253 users accessing the Internet in the same time. Dynamix UM-SB Series User Manual V0.06...
Page 29
Press Next to setup WAN1 parameters. Some of the ISP provides DHCP server service by which the PC in LAN can access IP information automatically. To setup the DHCP client mode, follow the procedure Dynamix UM-SB Series User Manual V0.06...
Page 30
Press Next to setup Remote DHCP server parameter. If using DHCP relay service, there must set up the remote DHCP server IP address Enter DHCP server IP address in IP address field. Press Next Dynamix UM-SB Series User Manual V0.06...
Page 31
Click Next. Note: For safety, the password will be prompt as star symbol. Username : Enter the user name exactly as your ISP assigned. Password: Enter the password associated with the user name above. Dynamix UM-SB Series User Manual V0.06...
Page 32
This is the router subnet mask seen by external users on Internet. Your ISP will provide it to you. Gateway: 10.1.2.2 Your ISP will provide you the default gateway. DNS Server 1: 168.95.1.1 Your ISP will provide at least one DNS (Domain Name System) Server IP address. Dynamix UM-SB Series User Manual V0.06...
Page 33
The screen will prompt the parameters that will be written in NVRAM. Check the parameters before writing in NVRAM. Press Restart to restart the router working with new parameters or press Continue to setup another parameter. Dynamix UM-SB Series User Manual V0.06...
LAN. Bridged connections do not use the IP protocol. EoA can also be configured to provide a routed connection with the ISP, which uses the IP protocol to exchange data. Dynamix UM-SB Series User Manual V0.06...
Page 35
Ethernet protocol or ATM protocol, which supports multiple users in a local area network. The PPP protocol information is encapsulated within an Ethernet frame or ATM frame. Dynamix UM-SB Series User Manual V0.06...
Advanced setup contains SHDSL.bis, WAN, Bridge, VLAN, Ethernet, Route, NAT/DMZ, Virtual SERVER, FIREWALL and IP QoS parameters. You can setup the Annex type, data rate and SNR margin for SHDSL.bis parameters in UM-SB. Click UM-SB Enter Parameters in UM-SB Dynamix UM-SB Series User Manual V0.06...
M – Pair Mode In this mode, each wire pairs of Dynamix UM-SB router must be configured with the same line rate. If one pair fails then the entire line must be restarted. It also has the Conexant M-pair standard used with connection to other router with Conexant chip set solution.
You can setup the SHDSL.bis data rate in the multiple of 128kbps. The default data rate is 11392Kbps (n=89). For using Annex AF or BG TCPAM32 ; data rate is 1536Kbps ~ 11392Kbps (Nx128kbps, N=12~ 89) Dynamix UM-SB Series User Manual V0.06...
PVCs such as WAN 2 to 7, those parameters are setup on the pages of WAN under ADVANCED. On the other hand, you don’t need to setup WAN except you apply two or more Internet Services with ISPs. Dynamix UM-SB Series User Manual V0.06...
Page 40
VC for each carried protocol. VPI (Virtual Path Identifier) is for set up ATM Permanent Virtual Channels(PVC).The valid range for Dynamix UM-SB Series User Manual V0.06...
Page 41
ISP assigns you a differnet on each time you connect to the Internet. Press Finish to finish setting. The screen will prompt the parameters that will be written in NVRAM. Check the parameters before Dynamix UM-SB Series User Manual V0.06...
Press Restart to restart the router working with new parameters or press continue to setup another parameter. If you want to setup advanced filter function while router is working in bridge mode, you can use BRIDGE menu to setup the filter function, blocking function. Click Bridge to setup. Dynamix UM-SB Series User Manual V0.06...
Page 43
The screen will prompt the parameters that will be written in NVRAM. Check the parameters before writing in NVRAM. Press Restart to restart the router working with new parameters or press Continue to setup another parameter. Dynamix UM-SB Series User Manual V0.06...
The IEEE 802.1Q defines the operation of VLAN bridges that permit the definition, operation, and administration of VLAN topologies within a bridged LAN infrastructure. The router supports two types of VLAN: 802.1Q Tag-Based VLAN and Port-Based VLAN. User can configure one of them to the router. Dynamix UM-SB Series User Manual V0.06...
Port-Based VLANs are VLANs where the packet forwarding decision is based on the destination MAC address and its associated port. For setting Port-Based VLAN, Click Port-Based VLAN, The screem will prompt as following: Dynamix UM-SB Series User Manual V0.06...
Page 46
The default setting is all ports (LAN1 to LAN4 and WAN1 to WAN8) connected together which means all ports can communicate with each other. That is, there are no virtual LANs. The option is the most flexible but the least secure. Dynamix UM-SB Series User Manual V0.06...
Spanning-Tree Protocol operation is transparent to end stations, which are unaware whether they are connected to a single LAN segment or a switched LAN of multiple segments. Dynamix UM-SB Series User Manual V0.06...
The Router, using the RIP protocol, determines the network packets’ route based on the fewest number of hops between the source and the destination. The RIP protocol regularly broadcasts routing information to other routers on the network. Click Route to modify the routing information. Dynamix UM-SB Series User Manual V0.06...
Page 49
To modify the RIP (Routing information protocol) Parameters: RIP Mode: Enable Auto RIP Summary: Enable Press Modify RIP Mode: This parameter determines how the router handle RIP (Routing information protocol). RIP allows it to exchange routing information with other router. Dynamix UM-SB Series User Manual V0.06...
Page 50
Authentication required: None: for RIP, there is no need of authentication code. Password: the RIP is protected by password, authentication code. MD5: The RIP will be decoded by MD5 than protected by password, authentication code. Dynamix UM-SB Series User Manual V0.06...
Page 51
You can set up a authentication code on here. After modifying the RIP parameters, press finish. The screen will prompt the modified parameter. Check the parameters and perss Restart to restart the router or press Continue to setup another parameters. Dynamix UM-SB Series User Manual V0.06...
DMZ provides access to no other company data. In the event that an outside user penetrated the DMZ host’s security, the Web pages might be corrupted, but no other company information would be exposed. Press NAT/DMZ to setup the parameters. Dynamix UM-SB Series User Manual V0.06...
The screen will prompt the parameters that will be written in NVRAM. Check the parameters before writing in NVRAM. Press Restart to restart the router working with new parameters or Continue to configure another parameter. Dynamix UM-SB Series User Manual V0.06...
Click Virtual Server to configure the parameters. There have ten virtual server index form 1 to 10 can been set up. Dynamix UM-SB Series User Manual V0.06...
Page 55
192.168.0.2, private port 80, public port 80, schedule from Day Monday to Friday and time 8:0 to 16:0 and index 2, protocol UDP, interface WAN1, service name test2, private IP 192.168.0.3, private port 25, public port 25, schedule always. Dynamix UM-SB Series User Manual V0.06...
NAT function is enabled. The remote management security is default to block any WAN side connection to the device. Non-empty legal IP pool in ADMIN will block all remote management connection except those IPs specified in the pool. Dynamix UM-SB Series User Manual V0.06...
Press Restart to restart the router or press Continue to setup another function. Click Automatic Firewall Security. This level enables basic firewall security, all DoS protection, and the SPI filter function. Press Finsih to finish setting firewall. Dynamix UM-SB Series User Manual V0.06...
DoS protection and defining an extra packet filter. Please notice that an improper filter policy may degrade the capability of the firewall and even block the normal network traffic. It can set up the DoS protection parameters Dynamix UM-SB Series User Manual V0.06...
Page 59
UDP echo traffic to IP broadcast addresses, all of it having a fake source address. This is a simple rewrite of the smurf attack code. For SYN attack, ICMP flood and UDP flood, they can set up the threshold of packets number per Dynamix UM-SB Series User Manual V0.06...
Page 60
If you want to configure the Packet Filtering Parameters, choose Enable and press Add. It can setup the packet filter rule parameters: Select the Protocol and configure the parameter. Protocol: ANY, TCP, UDP, ICMP, GRE, RSVP, ESP and AH.(ANY means all protocol) Dynamix UM-SB Series User Manual V0.06...
Page 61
Click Enable on Trigger Packet Filtering Service item, to active the packet filtering service. Click Enable on Drop Fragmented Packets item, to active the drop fragmented packets operation. You can modify or delete the access policies by click Modify or Delete command. Dynamix UM-SB Series User Manual V0.06...
IP QoS is a function to decide the priorities of setting IPs to transfer packets under the situation of overloading bandwidth. Click Enable at item Trigger IP QoS Service in General IP QoS Parameter, which will turn on this IP QoS function. Dynamix UM-SB Series User Manual V0.06...
Page 63
Precedence: type the session’s prioritized level you classify, “0” is lowest priority, “5” is highest priority. Click OK when all parameters are finish. You can modify or delete the policies by click Modify or Delete command Dynamix UM-SB Series User Manual V0.06...
Page 64
Click Finish can make a review for all IP QoS parameter To let the IP QoS configuration you have changed and want those take effect immediately, please click Restart button to reboot the system. To continue the setup procedure, please click Continue button. Dynamix UM-SB Series User Manual V0.06...
ROUTE Portname. INTERFACE LAN and WAN statistics information. FIREWALL Current DoS protection status and dropped packets statistics. IP QoS Show IP QoS statistics on LAN interface STP information include Bridge parameter and Ports Parameter Dynamix UM-SB Series User Manual V0.06...
Page 66
It the router is 2-wire model, no any channel B information you can see. Click Clear CRC Error can clear the CRC error count. Dynamix UM-SB Series User Manual V0.06...
For each IP address, the routing table additionally stores a network mask and other data that specifies the destination IP address ranges that remote device will accept. This information shows the IP routing table. Dynamix UM-SB Series User Manual V0.06...
The field shows the number of transmitted packets on this port InDiscards The field shows the discarded number of received packets on this port OutDiscards The field shows the discarded number of transmitted packets on this port Dynamix UM-SB Series User Manual V0.06...
The field shows the number of transmitted packets on this port OutDiscardsOctets The field shows the discarded number of transmitted bytes on this port OutDiscardsPackets The field shows the discarded number of transmitted packets on this port Dynamix UM-SB Series User Manual V0.06...
Root Port: Identifies the Port through which the path to the Root is established, and is not significant when the Bridge is the Root and is set to zero. It is the Port Identifier of the Port that offers the lowest Cost Path to the Root Dynamix UM-SB Series User Manual V0.06...
Page 74
Forwarding: When a port receives or sends data. In other words, this is operating normally. Disabled: This is when the network administrator has disabled the port. Blocking: this means the port was blocked to stop a looping condition. Dynamix UM-SB Series User Manual V0.06...
Router. The menu is meaning menu driven interface mode and Command is meaning line command mode. We will not discuss command mode in this manual. The default user name on and Password are “admin”. Dynamix UM-SB Series User Manual V0.06...
Page 76
PC in LAN can access the router. If you type the excact IP address in the filed, only the host on this listing can access to the router. Click Finish to finish the setting. Dynamix UM-SB Series User Manual V0.06...
The router can generate SNMP traps to indicate alarm conditions, and it relies on SNMP community strings to implement SNMP security. This router support both MIB I and MIB II. Click SNMP to configure the parameters. Dynamix UM-SB Series User Manual V0.06...
IP Address: type the trap host IP address Community: type the community password. The community is setup in community pool. Press OK to finish the setup. The browser will prompt the configured parameters and check it before writing into NVRAM. Dynamix UM-SB Series User Manual V0.06...
3. Specify an server name to which all syslog messages will be sent. 4. Specify a UDP port number to which the syslog server is listening. The default value is 514. Make sure this is not blocked from your firewall. Dynamix UM-SB Series User Manual V0.06...
Simple Network Time Protocol with Version 4 For synchronization with PC, select Sync with PC. The router will synchronize the time with the connecting PC. The function can supported on both bridge and router mode. Dynamix UM-SB Series User Manual V0.06...
Page 81
Update Period: How many times the router can resynchronize to time server. The unit is second. Press Finish to finish the setup. The browser will prompt the configured parameters and check it before writing into NVRAM. Dynamix UM-SB Series User Manual V0.06...
Load the factory default configuration, restore configuration and backup CONFIG TOOL configuration UPGRADE Upgrade the firmware LOGOUT Logout the system RESTART Restart the router. Click System Info for review the information. The browser will prompt the system information. Dynamix UM-SB Series User Manual V0.06...
IP network to syslog servers that collect the event message. The router can generate a syslog message and send it to a syslog server. Press SYSLOG, it send the syslog messages shown as follows: Dynamix UM-SB Series User Manual V0.06...
This configuration tool has three functions: load Factory Default, Restore Configuration, and Backup Configuration. Press CONFIG TOOL. Dynamix UM-SB Series User Manual V0.06...
Backup Configuration and then press Finish. Browse the place of backup file name or put the name. Then press OK. The router will automatically backup the configuration. If you don’t put the file name, the system will use the default: config1.log Dynamix UM-SB Series User Manual V0.06...
Press Upgrade in UTILITY. Select the firmware file name by click Browse on your PC or NB and press OK button to upgrade. The system will reboot automatically after finish the firmware upgrade operation. Dynamix UM-SB Series User Manual V0.06...
To logout the router, press LOGOUT in UTILITY. For logout system and close window, click the LOGOUT in UTILITY When click the Yes button, the Router will logout and browser window will be closed. Dynamix UM-SB Series User Manual V0.06...
When the restart button been clicked, the router will restarting and the browser session will be disconnected. This may appear as if your browser session is hung up. After the router restarts, you may either click the browser’s reload button or close the browser and re-open it later. Dynamix UM-SB Series User Manual V0.06...
Click Bridge and CO Side to setup Bridging mode of the Router and then click Next. Enter LAN Parameters IP: 192.168.0.1 Subnet Mask: 255.255.255.0 Gateway: 192.168.0.1 Host Name: SOHO Dynamix UM-SB Series User Manual V0.06...
Host Name: SOHO Enter WAN1 Parameters VPI: 0 VCI: 32 Click LLC Click Next The screen will prompt the new configured parameters. Check the parameters and Click Restart The router will reboot with the new setting. Dynamix UM-SB Series User Manual V0.06...
Click ROUTE and CO Side to setup Routing mode of the Router and then click Next Type LAN parameters: IP Address: 192.168.20.1 Subnet Mask: 255.255.255.0 Host Name: SOHO DHCP Service: Disable or Enable For more DHCP service, review the chapter on DHCP Service Type the WAN1 Parameters; VPI: 0 Dynamix UM-SB Series User Manual V0.06...
The screen will prompt the parameters that we will write in NVRAM. Check the parameters before writing in NVRAM. Press Restart to restart the router working with new parameters or press continue to setup another parameter. Click ROUTE and CPE Side then press Next. Dynamix UM-SB Series User Manual V0.06...
Page 93
Note: The Protocol used in CO and CPE have to be the same. Click Next to setup the IP parameters. For more understanding about NAT, review the chapter of NAT/DMZ. IP Address: 192.168.30.2 Subnet mask: 255.255.255.0 Gateway: 192.169.30.1 Click Next Dynamix UM-SB Series User Manual V0.06...
Page 94
The screen will prompt the parameters that we will write in NVRAM. Check the parameters before writing in NVRAM. Press Restart to restart the router working with new parameters or press continue to setup another parameter. Dynamix UM-SB Series User Manual V0.06...
Press the SPACE key until the login screen appears. When you see the login screen, you can logon to Router. Note: Only SPACE key invoke the login prompt. Pressing other keys does not work. User: admin Password: ***** Note: The factory default User and Password are “admin” both. Dynamix UM-SB Series User Manual V0.06...
VT100 terminal emulation and connecting to the management IP of Router, wait for the login prompt appears. Input User and Password after login screen pop up, User: admin Password: ***** Note: The default IP address is 192.168.0.1. Dynamix UM-SB Series User Manual V0.06...
For example, to show the system information, just logon to the Router, move down the cursor by pressing key K twice and select “show” command by key L , you shall see a submenu and select “system” command in this submenu, then the system will show you the general information. Dynamix UM-SB Series User Manual V0.06...
<Route|Bridge>. [1~1999] An item enclosed in brackets is optional. [1~65534|-t] Two or more items enclosed in brackets and separated by vertical bars means that you can choose one or none of the items. Dynamix UM-SB Series User Manual V0.06...
Modify command privilege status Show running system status show View system configuration ping Packet internet groper command exit Quit system ------------------------------------------------------------------------ If you need setup and manage the router, you must set enable command before. Dynamix UM-SB Series User Manual V0.06...
NVRAM and reboot the system, otherwise, all of your changes will not take effect. ping Internet ping command. admin You can setup management features in this command. Dynamix UM-SB Series User Manual V0.06...
Clear all statistics data Move cursor “ >> “ to shdsl.bis and press enter. If the Router is four wires model, there will show two channel’s status as the following: ----------------------------------------------------------------------------- Monitoring Window... <SHDSL.bis Status> Dynamix UM-SB Series User Manual V0.06...
37 LLC Ethernet WAN7 192.168. 7. 1/255.255.255. 0 38 LLC Ethernet WAN8 192.168. 8. 1/255.255.255. 0 39 LLC Ethernet ------------------------------------------------------------------------ Show WAN status include IP address, Net Mask, VPI/VCI, encapsulation type, protocol on each Dynamix UM-SB Series User Manual V0.06...
You can view interface statistics data on one LAN port and maximum eight WAN ports. Move cursor “ >> “ to firewall and press enter. ----------------------------------------------------------------------------- Monitoring Window... <Current Firewall Status> Attack Type Current Status History Status ---------------------- -------------- -------------- All DoS protects are disabled! ---------------------- -------------- -------------- Dynamix UM-SB Series User Manual V0.06...
WAN8 ---------- ---- ---- ---- ---- ---- ---- ---- ---- ---- State Priority Path Cost <Hint> D-Disable, B-Blocking, LS-Listening, LN-Learning, F-Forwarding. ----------------------------------------------------------------------------- You can view all STP status on all LAN and WANs ports. Dynamix UM-SB Series User Manual V0.06...
Show all configuration in command script Command Description system The general information of the system will show in system command. config Config command can display detail configuration information. script Configuration information will prompt in command script. Dynamix UM-SB Series User Manual V0.06...
Move cursor to “ >> “ to write and press enter. ---------------------------------------------------------------------- Command: write <CR> Message: Please input the following information. Are you sure? (y/n): y ---------------------------------------------------------------------- Press “y” to confirm the write operation. Dynamix UM-SB Series User Manual V0.06...
You can modify the user profile, security, SNMP (Sample Network Management Protocol), supervisor information and SNTP (Simple Network Time Protocol) in admin. For configuration the parameters, move the cursor “ >> “ to admin and press enter. Dynamix UM-SB Series User Manual V0.06...
The screen will prompt as follow: ------------------------------------------------------------------------ Command: admin user modify 5 profile <name> <pass_conf> Message: Please input the following information. Legal user name (ENTER for default) <admin>: superman Input the old Access password: **** Dynamix UM-SB Series User Manual V0.06...
Security command can be configured sixteen legal IP address for telnet access and telnet port number. Move the cursor “ >> “ to security and press enter. >> port Configure telnet TCP port ip_pool Legal client IP address pool list Show security profile Dynamix UM-SB Series User Manual V0.06...
SNMP security. This router support MIB I & II. Move the cursor “ >> “ to snmp and press enter. >> community Configure community parameter trap Configure trap host parameter Dynamix UM-SB Series User Manual V0.06...
Trap host entry number <1~5> : 2 ---------------------------------------------------------------------- The screen will prompt as follow: >> edit Edit trap host parameter list Show trap configuration Move the cursor to edit and press enter, you can setup the following: Dynamix UM-SB Series User Manual V0.06...
Command: admin id <pass_conf> Message: Please input the following information. Legal user name (Enter for default) <root> : test ---------------------------------------------------------------------- The default admin ID is “root”. Supervisor ID and Password: Supervisor ID Supervisor Password Dynamix UM-SB Series User Manual V0.06...
Page 113
Can only ping test, view the status and configuration Exit Web Brower mode: Supervisor ID Supervisor Password All function can use Logout Administration: user Change User name and Password security snmp passwd Change supervisor password Change supervisor ID sntp Dynamix UM-SB Series User Manual V0.06...
Active SNTP v4.0 service (Tab Select) <Enable> : Enable ---------------------------------------------------------------------- Move the cursor to time_server1 and press enter. ---------------------------------------------------------------------- Command: admin sntp time_server1 <string> Message: Please input the following information. Time server address(Enter for default) <ntp-2.vt.edu> : ntp-2.vt.edu ---------------------------------------------------------------------- Dynamix UM-SB Series User Manual V0.06...
Page 115
: SNTP v4.0 Service : Enable Time Server 1 : ntp-2.vt.edu Time Server 2 : ntp.drydog.com Time Server 3 : ntp1.cs.wisc.edu Update Period : 3600 secs GMT Time Zone Offset : 8 hours ---------------------------------------------------------------------- Dynamix UM-SB Series User Manual V0.06...
Message: Please input the following information. TFTP server IP address (ENTER for default) <192.168.0.2>: 192.168.0.120 Upgrade filename (ENTER for default) <default.bin>: backup001.bin ------------------------------------------------------------------------ Type TFTP server IP address and backup filename of system configuration.. Dynamix UM-SB Series User Manual V0.06...
SNR margin; the better is line connection quality. If you set SNR margin in the field as 3, the SHDSL.bis connection will drop and reconnect when the SNR margin is lower than 3. On the other hand, the device will reduce the line rate and reconnect for better line connection. Dynamix UM-SB Series User Manual V0.06...
Configure account name, password and idle time ip_type Configure IP type in PPPoA and PPPoE list WAN interface configuration WAN parameter: WAN interface number(1~8) □Disable □Ethernet □PPPoA □IPoA □PPPoE Protocol Address Mask □VC-Mux □LLC Encap Dynamix UM-SB Series User Manual V0.06...
Based on the PCR of the CBR traffic, specific cell slots are assigned for the VC in the schedule table. The ATM always sends a signle cell during the CBR connection’s assigned cell slot. VBR-rt (Varible Bit Rate real-time) is intended for real-time applications, such as compressed Dynamix UM-SB Series User Manual V0.06...
Move the cursor “ >> “ to bridge and press enter. >> gateway Default gateway static Static bridging table You can setup default gateway IP via gateway command. Bridge Gateway: Dynamix UM-SB Series User Manual V0.06...
To modify the VLAN rule, move the cursor “ >> “ to modify and press enter. ---------------------------------------------------------------------- Command: setup vlan modify <1~8> <1~4094> <string> Message: Please input the following information. Rule entry index <1~8>: 1 VLAN ID (ENTER for default) <1>: 10 VLAN port status (ENTER for default)<111111111>:111111111 Dynamix UM-SB Series User Manual V0.06...
Page 125
WAN port is automatically configured. If the product operates in bridge mode, the WAN link type will be trunk, and in routing mode, access. ---------------------------------------------------------------------- Command: setup vlan link_mode <1~12> <Access|Trunk> Message: Please input the following information. Port index <1~12>: 1 Port link type (Tab select) <Trunk>: Access ---------------------------------------------------------------------- Dynamix UM-SB Series User Manual V0.06...
Once you enable the STP feature, you can see the STP status will follow IEEE 802.1d standard to work. The working steps are Blocking, Listening, Learning and forwarding. You can setup the routing parameters in route command. If the product is configured as a bridge, Dynamix UM-SB Series User Manual V0.06...
You can add 20 sets of static route entry by using add command. Type the IP information of the static route including IP address, subnet mask and gateway. Static Route Table: IP Address Subnet Mask Gateway Dynamix UM-SB Series User Manual V0.06...
The product supports 8 PVCs and you can configure the RIP parameters of each WAN via wan command. Move the cursor “>>” to wan and press enter. ---------------------------------------------------------------------- Command: setup route rip wan <1~8> <more...> Message: Please input the following information. Dynamix UM-SB Series User Manual V0.06...
Address can set up IP address and subnet mask. Attrib can set up NAT network type: Global or Virtual. Ethernet item can set up the PHY parameters on this LAN port: Auto, 100M-Full, 100M-Half, 10M-Full and 10M-Half. LAN Port parameter: Dynamix UM-SB Series User Manual V0.06...
The virtual menu contains range of virtual IP address, delete virtual IP address, and show virtual IP address. >> range Edit virtual IP address pool delete Delete virtual IP address pool List Show virtual IP address pool You can create five virtual IP address pool range in range command. Dynamix UM-SB Series User Manual V0.06...
Page 131
Number of address: 3 ---------------------------------------------------------------------- After configuration global IP address range, you can bind address pool to specific interface via interface command. NAT (Global IP Address and range): Base Address Number of Address Active Interface Numbe(1~8) Dynamix UM-SB Series User Manual V0.06...
Page 132
Command: setup ip_share nat fixed modify <1~10> <ip> <ip> Message: Please input the following information. Fixed NAT mapping entry number <1~10>: 1 Local address: 192.168.0.250 Global address: 122.22.22.2 ---------------------------------------------------------------------- Fixed Address Mapping: Local Address Global Address Dynamix UM-SB Series User Manual V0.06...
To configure Port Address Translation, move the cursor “>>” to pat and press enter. >> clear Clear virtual server mapping modify Modify virtual server mapping list Show virtual server mapping pool You can delete virtual server mapping entry- from 1 to 10- by using clear command. Dynamix UM-SB Series User Manual V0.06...
You can view the fixed NAT mapping entry via list command. DMZ (demilitarized zone) is a computer host or small network inserted as a “neutral zone” between a company private network and the outside public network. It prevents outside users from Dynamix UM-SB Series User Manual V0.06...
Configure packet filter dos_protect Configure DoS protect ---------------------------------------------------------------------- There are three level of firewall, which you can setup in this product. Level one, basic, only enables the NAT firewall and the remote management security. The NAT Dynamix UM-SB Series User Manual V0.06...
Configure protocol type >> direction Configure direction mode src_ip Configure source IP parameter dest_ip Configure destination IP parameter port Configure port parameter (TCP and UDP only) tcp_flag Configure TCP flag (TCP only) Dynamix UM-SB Series User Manual V0.06...
TCP flag □ANY □SYN □ACK (ICMP only) □Echo_Reply □Dest_Unreach □Src_Quench □Redirect □Echo_Request □R_Advertise □R_Solicit ICMP flag □T_Exceed □Param_Problem □T_Stamp □T_Stamp_Reply □Info_Request □Info_Reply □Addr_Mask_Request □Addr_Mask_Reply Description □ON □OFF Enable Begin Time End Time □DENY □PERMIT Action Dynamix UM-SB Series User Manual V0.06...
Page 138
This is a simple rewrite of the smurf attack code. DoS Protection □Disable □Enable SYN flood Packets per sec. 0~700 □Disable □Enable ICMP flood Packets per sec. 0~700 □Disable □Enable UDP flood Packets per sec. 0~700 □Disable □Enable PING of death Dynamix UM-SB Series User Manual V0.06...
Page 139
While in most cases the mapping is correct there are many cases when some service or client uses a port reserved for an another application. Dynamix UM-SB Series User Manual V0.06...
IP addresses from a central point and automatically sends a new IP address when a computer is plugged into a different place in the network. To configure DHCP server, move the cursor “ >> “ to dhcp and press enter. Dynamix UM-SB Series User Manual V0.06...
Name Server 1 IP Name Server 2 IP Name Server 3 IP Fixed Host IP Address list are setup via fixed command. >> add Add a fixed host entry delete Delete a fixed host entry Dynamix UM-SB Series User Manual V0.06...
IP addresses, all names must be translated into an IP address. This is the purpose of a Domain Name Server. Enter the IP address of DNS proxy use DNS proxy command. Move cursor “ >> “ to dns_proxy and press enter. ---------------------------------------------------------------------- Command: setup dns_proxy <IP> [IP] [IP] Dynamix UM-SB Series User Manual V0.06...
If you want to restore factory default, first move the cursor “ >> “ to default and then press enter. ---------------------------------------------------------------------- Command: setup default <name> Message: Please input the following information. Are you sure? (Y/N): y ---------------------------------------------------------------------- Press “y” to confirm the restore factory setting operation. Dynamix UM-SB Series User Manual V0.06...