Page 1
USER’S MANUAL Label Printer BTP- L580IIC Shandong New Beiyang Information Technology Co., Ltd...
Page 2
INFORMATION TECHNOLOGY CO., LTD. (hereinafter referred to as “SNBC”) reserves the right to improve products as new technology, components, software, and hardware become available. If users need further data about these products, please feel free to contact SNBC or your local dealer.
BTP-L580IIC User’s Manual Safety instructions Before installing and using the printer, please read the following items carefully: Safety warning 1. Warning Do not touch the cutter of the printer. Warning The print head is a thermal element and it is at a high temperature during printing or just after operation, therefore do not touch it or its peripherals for reasons of safety.
1 Overview 1.1 Introduction BTP-L580IIC is a high performance thermal printer, which can be widely used for real-time printing applications, such as retail, warehousing, logistics, medicine, etc. BTP-L580IIC can be connected with other devices via parallel, serial, USB, Ethernet or WLAN interface, it can provide drivers and label software for operating systems such as WINDOWS 2000/XP/Server2003/VISTA/ Server2008/WIN7, Linux, and MAC.
BTP-L580IIC User’s Manual 2.2 Cutter specifications Item Parameter Remarks Cutting mode Sliding blade Cutting time 600ms The time that one cut takes Cutting interval 30 cuts/min (Max.) Applicable 0.06~0.1mm Thermal paper or paper with the same thickness paper type Operating...
FUJI PHOTO FILM CO., LTD 2.3.3 Parameters of marked paper BTP-L580IIC can support marked paper printing and set the cutting and initial printing position accurately. Marked paper not only should meet the parameters of thermal paper roll, but also should meet the following requirements: L1 mark height: 3mm≤L1≤13mm...
BTP-L580IIC User’s Manual To ensure print effect, do not let hard objects scratch the thermal layer; When the temperature exceeds 70°C, the thermal layer will fade. Thus, do not use or store the paper in a place exposed to high temperature, high humidity, strong light, etc.;...
BTP-L580IIC User’s Manual 3 Appearance and modules 3.1 Appearance and modules 1—paper guide 2—paper near end sensor lever 3—mark sensor 4—platen roller 5—cutter 6—cutter cover board 7—tear-off bar 8—fixed blade 9—print head 10—guard board for print head 11—roller 12—cover open lever 13—top cover...
BTP-L580IIC User’s Manual Refer to Appendix Button Configuration Menu for the detailed function and operation method of button configuration mode; 2) If selecting “Calibration”, the printer will do paper calibration; 3) Select “Select Print Mode” to change print mode (label paper printing, or continuous paper printing).
4.1 Unpacking Check if all the articles listed in the packing list are here and in good condition. If any problem, please contact SNBC or the dealer. 4.2 Printer installation 1) Printer should be installed on a flat and stable place; horizontal installation is recommended and the inclination angle should not exceed ±10°...
BTP-L580IIC User’s Manual Caution: When the printer is bound to idle for a long period of time, disconnect the power cord. When the power is burned out or cannot be used for other reasons, replace it according to the following steps: 1) Press the power cover board and take it off in the direction indicated by the arrow;...
BTP-L580IIC User’s Manual 4.7 Install paper roll 4.7.1 Confirm paper type Paper can be installed after the connection of power cable and interface cable. But before starting printing, the paper type must be confirmed first. 4.7.2 Install/replace paper roll 1) Turn off the printer;...
BTP-L580IIC User’s Manual 4.8 Paper near end position adjustment Paper roll with different core can be used by adjusting paper near end sensor lever to the corresponding level with the minimal remaining amount of paper at level 1. Level Level...
BTP-L580IIC User’s Manual 4.10 Guide for hexadecimal dumping mode 4.10.1 Hexadecimal dumping function This function prints the data transmitted from the host computer in hexadecimal numbers and in their corresponding characters. Print sample in Hexadecimal Dump mode: 4.10.2 Running hexadecimal dumping 1) Start hexadecimal dumping by executing either of the following: a.
BTP-L580IIC User’s Manual 5 Routine maintenance Caution: Before starting routine maintenance, ensure that the printer power is turned off; Do not use solvents like gasoline or acetone; When cleaning sensors, the printer should not be powered on until the pure alcohol has completely evaporated.
Page 19
BTP-L580IIC User’s Manual Insert the U-Disk into the USB interface of printer; After opening the top cover, press the FEED button while powering on the printer; Release the button immediately when the error LED is on. The time of pressing the button after powering on the printer should be controlled within two seconds;...
BTP-L580IIC User’s Manual 6 Interface signal 6.1 Parallel interface Parallel interface can work in IEEE 1284 compatible mode or nibble mode. The interface is 36-pin socket. The Interface is defined as below: Signal Pin # Signal definition source nStrobe Data 0 (Least Significant Bit)
BTP-L580IIC User’s Manual 6.2 Serial interface The serial interface of the printer is compatible with RS-232, and the interface socket is DB25 female. PIN No. Signal definition PIN1 Frame ground PIN2 PIN 3 PIN 4 PIN 5 Not connected PIN6...
Support status back Support parameter configuration Support firmware online update Support HTTP function Supported protocols ICMP DHCP TFTP HTTP Wireless interface module uses wireless USB network card. For the main technical specifications, please contact your local dealer or SNBC. - 17 -...
BTP-L580IIC User’s Manual 6.6 Power interface definition Power interface signal definition Signal name Figure 6.6-1 Power socket 6.7 Signal definition of cash drawer interface Electrical features Driving voltage: DC 24V Driving current: Max. 1A Cash drawer status detection signal: “L” = 0~0.5 V “H”...
BTP-L580IIC User’s Manual 7 Troubleshooting Refer to this chapter for solution when a problem occurs. If the problem still cannot be solved, please contact your local dealer or SNBC for assistance. 7.1 Printer doesn’t work Problem Possible causes Solution Printer is not connected with...
Related parameters of power management are as below: Maximum default delay time of entering sleep mode is less than 5 minutes; Since the maximum default delay time is less than 5 minutes, BTP-L580IIC does not open the interface of changing this time to user.