Note
•
Communication cannot be established with
a party whose connection mode setting
differs from yours.
•
"NAT Traversal Mode" can be used only
after activating KX-VC Series NAT
Traversal Service with an activation key.
For details about KX-VC Series NAT
Traversal Service, refer to the following web
site:
http://panasonic.net/psn/products/hdvc/
nat_traversal/index.html
3.
Press [G].
•
A dialogue box to confirm the saving of settings
and system restart after saving is displayed.
4.
Use [
][
] to select "Yes" and press [ENTER].
•
The system will automatically restart to reflect
changes to system settings.
Note
•
When changing the connection mode, the time
required for a restart may depend on network
conditions.
Making NAT Settings
Note
•
To change the static NAT settings, it is
necessary to configure system settings,
including the port number settings. For details,
contact your dealer.
•
When using IP mode (Page 116), "NAT" is not
displayed in step 2.
•
When using NAT traversal mode (Page 116),
"Static NAT", "WAN IP Address", and "Local
address judgement" are not displayed in step
2.
•
This setting is available only when "IP
Address" is set to "Manual" in "Network
Settings" (Page 99).
1.
Select "NAT Settings" and press [ENTER].
•
The NAT settings screen is displayed.
2.
Use [
][
] to select the following items for input:
•
The following items are displayed over 2 pages.
To view all the items, press [R] to move to the
next page, and press [B] to move to the
previous page.
Document Version 2015-03
•
If the settings have been changed, press [G]
before changing to a different screen to save
the settings.
"NAT": Press [ENTER] and use [
"Dynamic" (default) or "Static".
"Static NAT": Use [
"OFF" (default).
Note
•
To select "ON", "H.460" must be set to
"OFF" on the H.323 settings screen
(Page 120).
•
When "ON" is selected, the IP address of
the WAN side will be displayed for the unit
information on the Home screen (Page 37).
"WAN IP Address": Enter the WAN IP address of
the router.
Note
•
If the IP address contains 1 or 2 digit
numbers, enter these numbers as they are.
Do not enter like [.001].
Example: The IP address is [192.168.0.1].
–
Correct entry: [192.168.0.1]
–
Wrong entry: [192.168.000.001]
•
If "Obtain automatically" is displayed, the
WAN IP address cannot be set. For details,
contact your dealer.
"Local address judgement": Press [ENTER] and
use [
][
] to select "OFF" (default) or "Auto".
–
"OFF" (default): Static NAT is applied to all
addresses.
–
"Auto": Static NAT is not applied to private
addresses.
"RTP and RTCP for Audio": Enter the initial port
number (5100–5164) for RTP and RTCP for Audio
(default: 5100).
"RTP and RTCP for Video": Enter the initial port
number (5200–5264) for RTP and RTCP for Video
(default: 5200).
"Camera Control": Enter the initial port number
(5300–5364) for controlling a video camera (default:
5300).
"RTP and RTCP for Video (Sub)": Input the sub
image RTP/RTCP port number (5400–5464).
(default: 5400)
"BFCP": Input the BFCP initial port number (5800–
5890). (default: 5800)
"SIP": Enter the port number for 2-party video
conference calls (5000–5099) for communication
using a SIP server (default: 5060).
Contacts and Settings
][
] to select
][
] to select "ON" or
User Manual
117