Making H.323 Settings - Panasonic KX-VC1600SX User Manual

Note
•
To communicate using a SIP server, "ON"
must be selected and "SIP Server
Address", "SIP Username", and "SIP
Domain Name" must be set.
•
To select "ON", "Gatekeeper" (Page 120)
must be set to "OFF".
"SIP Server Address": Enter the SIP server's IP
address (or host name).
Note
•
If the IP address contains 1 or 2 digit
numbers, enter these numbers as they are.
Do not enter like [.001].
Example: The IP address is [192.168.0.1].
–
Correct entry: [192.168.0.1]
–
Wrong entry: [192.168.000.001]
•
The DNS server setting is necessary to
enter host names (Page 99).
•
See Page 42 for details about the
characters that can be input for host names.
"SIP Username": Enter the SIP user name.
"SIP Domain Name": Enter the SIP domain name.
Note
•
See Page 42 for details about the
characters that can be input.
•
Enter a standards-compliant value. For
details, contact your network administrator.
"Digest Authentication": Use [
whether to enable digest authentication.
–
"ON": Enables digest authentication.
–
"OFF" (default): Disables digest authentication.
"Authentication ID": Enter an authentication ID
(1–60 characters [alphanumeric, space, symbols])
(Page 141). &, <, >, comma (,), double quotation
mark (") cannot be entered.
"Authentication Password": Enter an
authentication password (0–60 characters
[alphanumeric, space, symbols]) (Page 141). &, <,
>, comma (,), double quotation mark (") cannot be
entered.
Note
•
To communicate using a SIP server, it may
be necessary to set "Digest
Authentication", "Authentication ID",
and "Authentication Password". For
details, contact your network administrator.
•
"Authentication ID" and "Authentication
Password" can only be set when "Digest
Authentication" is set to "ON".
Document Version 2015-03
3.
4.
][ ] to select

Making H.323 Settings

Note
•
While being entered, the characters of the
authentication password are displayed, but
once the settings are saved, all the
characters will be displayed as asterisks (*),
and you will no longer be able to check the
authentication password on the screen.
Record the authentication password
beforehand, and store it in a safe location.
•
When the authentication password is
displayed as asterisks (*), pressing [Y]
deletes the entire authentication password.
"SIP Transport Protocol": Press [ENTER] and
then use [ ][ ] to select between protocols
(UDP, TCP, Auto (Switch by Site), or Auto (TCP /
UDP) [default]) used when communicating via SIP.
Note
•
When Auto (Switch by Site) is selected,
TCP will be used if using a SIP server, and
UDP will be used if not using a SIP server.
When Auto (TCP / UDP) is selected,
communication will be attempted in order of
TCP and then UDP. Normally, select Auto
(TCP / UDP).
Press [G].
•
A dialogue box to confirm the saving of settings
is displayed.
Use [ ][ ] to select "Yes" and press [ENTER].
•
The administrator menu screen is displayed.
•
These settings can only be made when "H.
323" is set to "ON" on the call type settings
screen.
•
When connecting to an MCU by entering the
MCU's conference room number@IP address,
"SIP Server" (Page 118) and "Gatekeeper"
must be set to "OFF".
•
If video conference calls cannot be made
because there is a problem with the gatekeeper
and H.460 server, the H.323 settings are
incorrect (on the gatekeeper and the H.460
server, or on the unit), etc., "Not registered"
will be displayed on the Home screen instead of
the H.323 extension/H.323 name. In this case,
you cannot make calls using either IP
Contacts and Settings
User Manual 119