JB Systems LED Crossfire Operation Manual page 5

ENGLISH
Working Mode
Used to set the unit in master or slave mode.
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the current working mode starts blinking in the display
 Use the DOWN and UP buttons to select
slave in anti-sync with the master).
 Once the right mode is selected, press the ENTER button to confirm.
 Press the MENU button for about 2 seconds to return to running mode.
Show Mode
Used to choose to select one of the preprogrammed shows when used in standalone or master/slave
mode.
 Press the MENU button until
is showing on the display.
 Press the ENTER button, the current show starts blinking in the display.
Use DOWN and UP buttons to select one of the preprogrammed shows
(show 1) to (show 12)
 Once the right show blinks on the display, press the ENTER button to save it.
 Press the MENU button for about 2 seconds to return to running mode.
Color mode
If you like you can set the effect to just one of the 15 fixed colors. If you want to return to the built-in
shows, just select Show mode and choose a show. With CA-8/RF-8SET you can select the different
colors and shows.
Colo
 Press the MENU button until
is showing on the display.
 Press the ENTER button, the current color starts blinking in the display.
 Use DOWN and UP buttons to select one of the preprogrammed colors
 Once the right color blinks on the display, press the ENTER button to save it.
 Press the MENU button for about 2 seconds to return to running mode.
Sound Mode
Used to choose the desired sound/manual mode to trigger the shows.
 Press the MENU button until
is shown on the display.
 Press the ENTER button to select.
 Use DOWN and UP button to select one of the available modes:

(sound mode ON)  the shows are triggered by the internal microphone.

(sound mode OFF)  the shows are triggered by the speed selected with the shows.
o The current speed blinks in the display
o Use DOWN and UP button to select one of the 3 available speeds.
 Once the right mode is selected, press the ENTER button to confirm.
 Press the MENU button for about 2 seconds to return to running mode.
Audio sensitivity
Depending on the situation you can adapt the audio input sensitivity, as a result the effect will always
respond perfectly to the beat!
SEnS
 Press the MENU button until
is showing on the display.
 Press the ENTER button, the current value starts blinking in the display.
 Use DOWN and UP buttons to select the desired sensitivity value:
(maximum sensitivity)
 Once the right value blinks on the display, press the ENTER button to save it.
 Press the MENU button for about 2 seconds to return to running mode.
JB SYSTEMS
®
OPERATION MANUAL
(slave in sync with the master) or (2 light show –
(random show), or
Col1 Co15
(color 1) to
0
(minimum sensitivity) to
5/63 LED CROSSFIRE
ENGLISH
Blackout mode: when no DMX-signal is detected, the unit goes in blackout.
No blackout mode: when no DMX-signal is detected, the unit automatically switches to master mode.
 Press the MENU button until
 Press the ENTER button, the current selection starts blinking in the display.
 Use DOWN and UP button to select Y E S (blackout) or n o (no blackout) mode.
 Once the mode is selected, press the ENTER button to save it.
 Press the MENU button for about 2 seconds to return to running mode.
Display on: display is always on.
Display off: display is off when not used.
 Press the MENU button until the display shows
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select
 Once the mode is selected, press the ENTER button to save it.
 Press the MENU button for about 2 seconds to return to running mode.
Display normal: display is readable when the unit is mounted upright.
Display inversion: display is readable when the unit is mounted upside down.
 Press the MENU button until
 Use the ENTER button to change to the mode
 Press the MENU button for about 2 seconds to return to running mode.
(color 15)
 Press the MENU button until
 Press the ENTER button: the unit will run the built-in programmer for self-test.
 To go back to the functions press the MENU button.
 Press the MENU button for about 2 seconds to return to running mode.
Used to show the number of working hours of the unit.
 Press the MENU button until
 Press the ENTER button to show the number of working hours in the display.
 To go back to the functions press the MENU button or press the MENU button for about 2 seconds to
return to running mode.
Used to show the software version of the unit.
 Press the MENU button until
 Press the ENTER button to show the software version of the unit.
 To go back to the functions press the MENU button or press the MENU button for about 2 seconds to
return to running mode.
100
JB SYSTEMS
Blackout Mode
is shown on the display.
Led Display
.
(display always on) or
Display Inversion
is blinking on the display. (normal display)
(display inversion).
Self-Test
is blinking on the display.
Fixture Hours
is blinking on the display.
Software version:
blinks on the display.
6/63
®
OPERATION MANUAL
(display off when not used).
LED CROSSFIRE