Installation Process Overview - Barco DP2K-12C Installation Manual

• One short power link cable (mono phase) (in case no UPS is used) - Installed on projector.
• This manual (installation manual).
• Safety manual
One xenon lamp is mounted inside the lamp house at delivery. The projector lenses are not included in the
package of the projector.
Mechanical check
This check should confirm that there are no broken knobs or connectors, that the cabinet and panel surfaces are free of dents and
scratches, and that the operating panel is not scratched or cracked. The Barco Sales and Service office should be notified as soon
as possible if this is not the case.
Tamper labels
During installation please inspect the tamper labels, if they are damaged please contact Barco tech support.
The tamper labels are required by DCI to provide easy visual indication if the equipment was tampered with. The projectors are
tested and labeled for shipping to ensure that the system was not compromised before reaching the customers final destination.
These tamper labels can be found behind the input cover.
2.4

Installation process overview

Let the projector acclimate to the ambient temperature after unpacking. Neglecting this may result in a startup
failure of the light processor unit.
Set up from A to Z
After you have unpacked and checked the projector you can start with the installation process of your DP2K C-series projector. This
chapter gives you an overview of all the different stages in the installation process which you have to follow to set your DP2K C-series
projector up and running. Each stage is briefly described and refers to more detailed step by step procedures in this manual. Use
this overview as a checklist to ensure that you have followed all stages in the setup process of your DP2K C-series projector.
Set up from A to Z
1. Check if all installation requirements are fulfilled such as the environment conditions of the installation area, capacity of the
exhaust system, electrical facilities, etc. Note that a solid pedestal is required to support the projector head. For more info see
chapter "Installation requirements", page 7.
2. Physical installation of the projector upon its pedestal and connecting the air outlet of the projector with the exhaust system.
Note that the exhaust system is MANDATORY. See chapters "Physical installation", page 13, and "Installation of the exhaust
system", page 15.
3. Electrical connection with the power net. See chapter "Connecting the projector with the power net", page 16.
4. Installation of a suitable UPS unit or bypass the power in and outlet for the projector electronics. See chapters "Connecting
a UPS with the projector electronics", page 19 or "Power loop through to the projector electronics", page 18.
5. Installation of the xenon lamp in case the xenon lamp is not installed in the lamp house yet. To install the xenon lamp the lamp
house has to be removed from the projector. To install the xenon lamp correctly and in a safe manner, see the detailed step by
step procedures in the chapter "Installation of the Xenon lamp", page 28.
6. Installation of the lens. First select an appropriate lens which throw ratio covers the screen size and the projector - screen
distance. Then install the lens in the lens holder of the projector. For more information about available lenses, lens selection and
lens installation see chapter "Lenses & lens holder", page 37.
7. Installation of the Communicator Touch Panel. See chapter "Installing the touch panel interface", page 54.
8. Alignment of the projected image on the screen. The projector can now be switched on to project its first image (test pattern)
on the screen. Then the image can be aligned with the screen size of the application. Follow the next steps to achieve that:
a) Place the ON/OFF switch of the projector in the "I" position. As a result the projector starts to initialize. The status lights of
the projector lights up GREEN once the projector is initialized.
b) Press the STANDBY button on the local keypad to activate the lamp.
c) Press the DOWSER button on the local keypad to open the dowser of the projector. The dowser is open if the color of the
DOWSER button is GREEN.
d) Press the TEST PATTERN button on the local keypad to project one of the internal test patterns of the projector on the screen.
e) Use the lens ZOOM, SHIFT and FOCUS buttons on the local keypad the match the projected image with the screen. Tilt the
projector in case you can not SHIFT the image completely upon the screen. See "Lens shift, zoom & focus", page 42.
R5905050 DP2K C-SERIES 10/07/2012
2. General
11