Table of Contents
Advertisement
4. Installation process
4.1
Installation process overview
Normally the projector is delivered with the xenon lamp installed. So, this installation process assumes that
the xenon lamp and Lamp House are already installed. If not, install the xenon lamp first prior to continue with
this process. See chapter "Lamp replacement process", page 81.
Installation process from A to Z
1. Check if all installation requirements are fulfilled such as the environment conditions of the installation area, capacity of the
exhaust system, electrical facilities, etc. Note that a solid pedestal is required to support the projector. For more info see topic
"Installation requirements", page 12.
2. Physical installation of the projector upon its pedestal and connecting the air outlet of the projector with the exhaust system.
Note that an external exhaust system is MANDATORY in case the exhaust output is on top of the projector. See chapters "Posi-
tioning the DP2K-S series projector at port window", page 20, and "Installation of the exhaust system", page 23.
3. Electrical connection with the power net. See chapter "Connecting the projector with the power net", page 25.
4. Installation of the lens. First select a lens with appropriate throw ratio covering the screen size and the projector - screen
distance. Then install the lens in the lens holder of the projector. For more information about available lenses, lens selection and
lens installation see chapter "Lens installation", page 30.
Caution:
The projector is delivered with a protective foam inside the Lens Holder. Remove the foam prior to installing the lens.
5. Installation of the IMB, IMS or HDSDI input module. See chapter "Input & Communication", page 35.
6. Installation of the Communicator Touch Panel. See chapter "Communicator Touch Panel", page 47.
7. Switch on the projector. The projector can now be switched on. Place the ON/OFF switch of the projector in the "I" position.
As a result the projector starts to initialize. The status lights of the projector lights up GREEN once the projector is initialized. In
case the status lights up RED may indicate a tamper event during transport. If so, contact Barco customer service.
8. Select the corresponding lens parameters for the installed lens. See user guide of the Communicator chapter Installation >
Advanced > Lens parameters.
9. Alignment of the projected image on the screen. The image can be aligned with the screen size of the application. Follow
the next steps to achieve that:
a) Press the STANDBY button on the Local Keypad to activate the lamp.
b) Press the DOWSER button on the Local Keypad to open the electronic dowser of the projector. The electronic dowser is open
if the color of the DOWSER button is GREEN.
c) Press the TEST PATTERN button on the Local Keypad to project one of the internal test patterns of the projector on the
screen.
d) Perform a "Lens Homing". See user guide of the Communicator.
e) Use the lens ZOOM, SHIFT and FOCUS buttons on the Local Keypad to match the projected image with the screen. Tilt the
projector in case you can not SHIFT the image completely upon the screen. See "Positioning the DP2K-S series projector at
port window", page 20.
See chapter "Local Keypad", page 37, for detailed description of the Local Keypad buttons.
10.Realignment of the xenon lamp in its reflector. For optimal performance of the xenon lamp realign the lamp. See "Realignment
of the lamp in its reflector", page 98, for more information.
11. Adjusting the light path. Normally the lens holder and the convergence of the projector are perfectly adjusted at the factory.
Nevertheless, some applications require a readjustment of the lens holder, convergence or both. See procedure "Scheimpflug
adjustment", page 60, and "Convergence", page 67.
12.Creating screen files, lens files, light sensor calibration (LSC) files, and macro files for FLAT and for SCOPE. See user
guide of the Communicator.
13.Backup of all projector configuration files. See user guide of the Communicator.
14.Registration of the projector. The DP2K-S series projector is DCI compliant and should be registered.
15.Projection of a digital cinema movie.
In case the projector is equipped with a HD-SDI input module apply a single or dual channel SMPTE (HD-SDI) source to the input
ports of the HD-SDI input module and start up the projector. See "Input & Communication", page 35, and chapter "Starting up",
page 53. Use the Communicator Touch Panel to configure the applied source. See the user guide of the Communicator Touch
Panel for more detailed information.
In case the projector is equipped with an Integrated Media Block (IMB) or Integrated Media Server (IMS) see user guide of the
IMB or IMS for detailed instructions.
18
R5977692 DP2K-S SERIES 10/12/2012
Advertisement
Table of Contents
