Husqvarna CR 125 2011 Workshop Manual page 242

Application
Upper chain guide ret. screw (WR)
Rear chain guide ret. screw (CR)
Front chain guide ret. screw (CR)
Slider ret. screw
Horn ret. screw (WR)
Headlight unit ret. screw (WR)
Front mudguard ret. screw
Front headlamp fairing ret. screw (WR)
Rear chain guide ret. screw (WR)
Rear mudguard ret. screw
Shock absorber protection ret. screw
Front number holder ret. screw (CR)
(*): "LOCTITE 242"
Application
Air scoop ret. screw
Front side panel ret. screw
Side number holder (rear) ret. screw
Front chain guide ret. screw (WR)
Tank front bumper ret. screw
Rear tank ret. screw
Front brake disc ret. screw
Front wheel axle ret. screw
Brake calliper ret. screw
Fuel cock ret. screw
Saddle front ret. screw
Air box ret. screw
Brake line to brake callipers ret. screw (WR)
Brake line to brake callipers ret. screw (CR)
(•): "LOCTITE 242"
Application
Wheel spoke ret. nipple
Rear brake disc ret. screw
Rear sprocket lock. nut
Exhaust pipe to chassis damping pad ret. screw
Exhaust silencer retaining screw
Damping pad to exhaust pipe retaining screw
Odometer locking nut (WR)
Turning indicator ret. screw (WR)
Rear wheel axle
NOTE - If not otherwise specified, standard torque values for the different thread sizes are as fol-
lows:
Workshop Manual Ed. 06-2011
TIGHTENING TORQUE FIGURES
CR 125 2011 - WR 125 2011
lower
upper
X.4
Thread Nm
M8x1.25 23.3÷26.5
M6x1 14÷15.4
M8x1.25 12.2÷13.3
M5x0.8 5.6÷6.2
M6x1 10.3÷11.3
M6x1 (•) 5.6÷6.2
M6x1 10.3÷11.3
M6x1 10.3÷11.3
M5x0.8 5.6÷6.2
M6x1 10.3÷11.3
M6x1 5.6÷6.2
M6x1 10.3÷11.3
M5x0.8 5.6÷6.2
Thread Nm
M6x1 5.6÷6.2
M6x1 3.2÷3.6
M6x1 5.6÷6.2
M5x0.8 5.6÷6.2
M8x1.25 21.6÷23.3
M6x1 10.3÷11.3
M6x1 (•) 17.6÷19.6
M10x1.5 49÷54
M8x1.25 23.3÷26.5
ø 5.5 2.35÷2.55
M6x1 5.6÷6.2
M6x1 10.3÷11.3
M10x1 18.1÷20.1
M10x1 23.5÷25.5
Thread Nm
M4x0.75 4.2÷4.6
M6x1 (*) 17.6÷19.6
M8x1.25 32÷36
M6x1 10.3÷11.3
M6x1 10.3÷11.3
M6x1 10.3÷11.3
M6x1 5.6÷6.2
M6x1 5.6÷6.2
M20x1.5 135.3÷149
M5x0.8 4.9÷6.9
M6x1 8.8÷9.8
M8x1.25 21.6÷23.3
Kgm ft/lb
2.4÷2.7 17.3÷19.5
1.43÷1.57 10.3÷11.3
1.24÷1.36 9÷9.8
0.57÷0.63 4.1÷4.5
1.05÷1.15 7.6÷8.3
0.57÷0.63 4.1÷4.5
1.05÷1.15 7.6÷8.3
1.05÷1.15 7.6÷8.3
0.57÷0.63 4.1÷4.5
1.05÷1.15 7.6÷8.3
0.57÷0.63 4.1÷4.5
1.05÷1.15 7.6÷8.3
0.57÷0.63 4.1÷4.5
Kgm ft/lb
0.57÷0.63 4.1÷4.5
0.33÷0.37 2.4÷2.7
0.57÷0.63 4.1÷4.5
0.57÷0.63 4.1÷4.5
2.2÷2.4 16÷17.3
1.05÷1.15 7.6÷8.3
1.8÷2.0 13÷14.5
5.0÷5.5 36.2÷39.8
2.4÷2.7 17.3÷19.5
0.24÷0.26 1.73÷1.88
0.57÷0.63 4.1÷4.5
1.05÷1.15 7.6÷8.3
1.85÷2.05 13.4÷14.8
2.4÷2.6 17.3÷18.8
Kgm ft/lb
0.43÷0.47 3.1÷3.4
1.8÷2.0 13÷14.5
3.3÷3.7 2.4÷2.7
1.05÷1.15 7.6÷8.3
1.05÷1.15 7.6÷8.3
1.05÷1.15 7.6÷8.3
0.57÷0.63 4.1÷4.5
0.57÷0.63 4.1÷4.5
13.8÷15.2 100÷110
0.5÷0.7 3.6÷5
0.9÷1 6.5÷7.2
2.2÷2.4 16,17,3