Husqvarna CR 125 2011 Workshop Manual page 240

ENGINE
APPLICATION
Cylinder ret. stud bolt (+LOCTITE 243)
Cylinder lock. nut
Head lock. nut
Pulley ret. screw
Cylinder ret. stud bolt (+LOCTITE 243)
Primary shaft plate ret. screw
Starter shaft ret. screw (+LOCTITE 270)
Oil drain plug
Intake valve ret. screw
Stator ret. screw (WR)
Stator ret. screw (CR)
Rotor lock. nut
Spark plug
Clutch hub lock. nut
Clutch spring ret. screw
Gear shift control sector gear ret. screw (+LOCTITE
270)
Ratchet bushing ret. screw (+LOCTITE 243)
Water pump sprocket lock. nut
Kick start lever ret. screw
Gear shift pedal ret. screw
Crankcase bearing plate ret. screw (+LOCTITE 243)
Rear cylinder ret. stud bolt (+LOCTITE 243)
Crankshaft insert ret. screw
Timing system lever ret. screw
Workshop Manual Ed. 06-2011
TIGHTENING TORQUE FIGURES
CR 125 2011 - WR 125 2011
THREAD
M8x1.25
M8x1.25
M8x1.25
M5x0.8
M8x1.25
M5x0.8
M6x1
M14x1.25
M6x1
M4x0.7
M6x1
M12x1.25
M14x1.25
M16x1
M6x1
M5x0.8
M6x1
M12x1
M6x1
M6x1
M6x1
M8x1.25
M5x0.8
M5x0.8
X.2
N.m. Kgm
19.6÷21.6 2.0÷2.2
17.6÷19.6 1.8÷2.0
17.6÷19.6 1.8÷2.0
5.1÷5.7 0.52÷0.58
19.6÷21.6 2.0÷2.2
5.1÷5.7 0.52÷0.58
9.3÷10.3 0.95÷1.05
23.5÷25.5 2.4÷2.6
7.8÷8.8 0.8÷0.9
3.0÷3.2 0.29÷0.33
8.8÷9.8 0.9÷1.0
73.5÷83.3 7.5÷8.5
23.5÷25.5 2.4÷2.6
27.4÷30.4 2.8÷3.1
6.9÷7.8 0.7÷0.8
5.1÷5.7 0.52÷0.58
8.8÷9.8 0.9÷1.0
46.1÷52.0 4.7÷5.3
8.8÷9.8 0.9÷1.0
8.8÷9.8 0.9÷1.0
7.9÷8.7 0.81÷0.89
19.6÷21.6 2.0÷2.2
9.8 1
5.9 0.6
ft/lb
14.5÷15.9
13.0÷14.5
13.0÷14.5
3.8÷4.2
14.5÷15.9
3.8÷4.2
6.9÷7.6
17.3÷18.8
5.8÷6.5
2.1÷2.4
6.5÷7.2
54.2÷61.5
17.3÷18.8
20.2÷22.4
5.1÷5.8
3.8÷4.2
6.5÷7.2
34÷38.3
6.5÷7.2
6.5÷7.2
5.8÷6.4
14.5÷15.9
7.2
4.3