Yamaha Grizzly550 User Manual page 67

1. Wire harness
2. Fuel hose
3. Intake air temperature sensor lead
4. Final drive case breather hose
5. Ground lead
6. Starter motor lead
7. Air filter case breather hose
8. Coolant temperature sensor lead
9. Throttle body breather hose
10. Main switch lead
11. Auxiliary DC jack lead
12. EPS motor lead (YFM5FGP/YFM7FGP only)
13. Differential motor lead
14. EPS torque sensor lead (YFM5FGP/YFM7FGP
only)
15. Radiator fan motor lead
16. Radiator inlet hose
17. EPS motor breather hose (YFM5FGP/YFM7FGP
only)
18. Spark plug lead
19. Rear brake cable
20. Shift control cable
21. Fuel tank drain hose
22. Gear position switch lead
23. Speed sensor lead
24. AC magneto/crankshaft position sensor lead
25. Fuel injector lead
26. Radiator fan motor breather hose
27. EPS torque sensor coupler (YFM5FGP/YFM7FGP
only)
A. Route the fuel hose between the wire harness and
the fuel tank drain hose.
B. Route the air filter case breather hose to the
outside of the leads, and then fasten the hose with
the holder on V-belt cooling intake duct joint.
C. Route the throttle body breather hose under the
coolant temperature sensor lead.
D. Route the EPS motor breather hose
(YFM5FGP/YFM7FGP only) and radiator fan motor
breather hose above the V-belt cooling intake duct.
E. Route the final drive case breather hose above the
V-belt cooling intake duct.
F. Route the radiator fan motor lead between the
electrical components tray and the radiator inlet
hose.
G. Fasten the radiator fan motor lead and radiator fan
motor breather hose to the frame with the plastic
band, making sure to face the end of the band
inward.
H. Route the spark plug lead to the outside of the rear
brake cable and shift control cable.
I. Route the fuel tank drain hose to the inside of the
leads and fuel hose, making sure to position the
end of the drain hose as shown in the illustration.
J. Fasten the final drive case breather hose, ground
lead, starter motor lead, fuel injector lead, coolant
temperature sensor lead, AC magneto/crankshaft
position sensor lead, and wire harness with the
plastic band, making sure to position the band near
the split in the wire harness.
K. Route the fuel injector lead and coolant
temperature sensor lead to the inside of the ground
lead, starter motor lead, final drive case breather
hose, and wire harness.
L. Face the end of the plastic band inward.
M. Pass the plastic band through the hole in the
plastic cover, and then fasten the wire harness,
final drive case breather hose, ground lead, and
starter motor lead with the band, making sure to
face the end of the band downward.
N. The ends of the EPS motor breather hose
(YFM5FGP/YFM7FGP only) and radiator fan motor
breather hose should extend rearward past the
inlet of air filter case as shown in the illustration.
O. Route the EPS motor breather hose
(YFM5FGP/YFM7FGP only) and radiator fan motor
breather hose under the air chamber.
P. Route the EPS motor breather hose
(YFM5FGP/YFM7FGP only) and radiator fan motor
breather hose rearward and pass them through the
guide.
Q. Insert the projection on each coupler into the hole
in the frame from the inside of the frame.
(YFM5FGP/YFM7FGP only)
R. Face the end of the plastic band inward.
S. Fasten the spark plug lead with the larger diameter
section of each holder.
T. YFM5FGP/YFM7FGP
U. YFM5FG/YFM7FG
2-38
CABLE ROUTING
techsparkstudio.com