Panasonic UF-585 Service Manual page 145

No. Parameter (see Note 3)
017 TX START
018 RX START
019 ITU-T V.34
(UF-595 only)
020 ITU-T ECM
021 EP TONE
022 SIGNAL. INTERVAL
023 TCF CHECK
024 CED FREQUENCY.
025 COMM. START-UP
026 NON-STANDARD
027 SHORT PROTOCOL B
028 SHORT PROTOCOL D
(UF-595 only)
029 REMOTE DIAGNOSTICS.
030 CED & 300 bps
031 RTC = EOLx12
032 V.34 TX START
(UF-595 only)
033 V.34 RX START
(UF-595 only)
034 V.34 TX Symbol Rate
(UF-595 only)
035 V.34 RX Symbol Rate
(UF-595 only)
036 Not Used
037 PROTOCOL DISPLAY
038 Not used
039 FLASH TIME
040 E/F TIME (For Germany,
Austria and Switzerland only)
Function Parameter Table
Selections
• 2400 bps
• 4800 bps
• 7200 bps
• 9600 bps
• TC7200 bps
• TC9600 bps
• 12000 bps
• 14400 bps
• 2400 bps
• 4800 bps
• 7200 bps
• 9600 bps
• TC7200 bps
• TC9600 bps
• 12000 bps
• 14400 bps
1 = Off
2 = On
3 = Select
1 = Off (Invalid)
2 = On (Valid)
1 = Off (without EP Tone)
2 = On (with EP Tone)
1 = 100 ms
2 = 200 ms
3 = 500 ms
1 = Normal (Short)
2 = Long
1 = 1080 Hz (non CCITT)
2 = 2100 Hz
1 = 1'st response
2 = 2'nd response
1 = Off (Invalid)
2 = On (Valid)
1 = Off (Invalid)
2 = On (Valid)
1 = Off (Invalid)
2 = On (Valid)
1 = Off (will not accept)
2 = On (accepts)
1 = 75 ms
2 = 1 sec
1 = Off (EOLx6)
2 = On (EOLx12)
2400-33600bps
2400-33600bps
2400-3429sr
2400-3429sr
1 = Off (not displayed)
2 = On (displayed)
5 = 50 ms
~
100 = 1000 ms
5 = 50 ms
~
100 = 1000 ms
145
Function
Selects the transmission modem start speed,
14400/12000/TC9600/TC7200/9600/7200/4800/
2400 bps.
Note:
This parameter is applicable only when communi-
cating with regular G3 machines.
nicating with Super G3 (V.34) machines, use
Parameter #32.
Selects the reception modem start speed, 14400/
12000/TC9600/TC7200/9600/7200/4800/2400 bps.
Note:
This parameter is applicable only when communi-
cating with regular G3 machines.
nicating with Super G3 (V.34) machines, use
Parameter #33.
Selects whether the ITU-T V.34 is Off, On or Select.
(Select: Select whether the ITU-T V.34 is Off or On,
when entering One-Touch/Abbreviated Dialing
Numbers or Manual Number Dialing.)
Select the ECM mode.
Selects the echo protect tone on V.29 mode, On
(Add) or Off (Not add).
(Used when Echo Suppression is disabled.)
Selects the time interval between the receiving
signal and the transmitting signal.
Selects the TCF check interval Long/Short
Selects the CED frequency 2100/1080 Hz
Selects the communication start-up condition (XMT
and Polling).
(Used when Echo Suppression is disabled.)
Selects own mode (Panafax mode).
Selects the short protocol (TYPE B) mode.
Selects the short protocol (TYPE D) mode.
Selects whether the machine accepts the Remote
Diagnostics from the service station.
Selects the pause interval between the CED and
the 300 bps signal.(Used when Echo Suppression
is disabled.)
Selects the RTC signal, EOLx6 or EOLx12.
Selects the transmission modem start speed in
V.34 communication, 33600-2400bps.
Selects the receiving modem start speed in V.34
communication, 33600-2400bps.
Selects the transmission symbol rate for V.34,
3429/3200/3000/2800/2400 sr.
Press "V" or "/\" to select the symbol rate.
Selects the receiving symbol rate for V.34,
3429/3200/3000/2800/2400 sr.
Press "V" or "/\" to select the symbol rate.
Selects whether to display the modem speed
during communication. (Press "\/" or "/\" to display)
Selects the pause interval before activating the
Flash key.
Selects the pause interval before activating the
Flash key.
When commu-
When commu-