Panasonic UF-585 Service Manual page 134

Code Mode Phase
402 XMT
403 RCV(Polling)
404 XMT
405 XMT
406 RCV(Pass-
word Comm.)
407 XMT
408 XMT
409 XMT
410 RCV
411 RCV(Polling)
412 G3 RX B,D
414 RCV(Polling)
415 XMT(Polling)
416 RCV
417 RCV
418 RCV
420 RCV
421 RCV
422 XMT
427 G3 RCV
433 XMT B,D
RCV
Information Codes
Description of Problem
B DCN was returned from receiver while
transmitter is waiting for NSF/DIS.
B Transmitter had no polling function.
B Transmitter sent NSS (or DCS) followed by TCF
three times, but the receiver did not respond.
(CFR or FTT is usually returned)
B Transmitter received FTT after it transmitted
TCF at 2400bps.
Received RTN after communicating at 2400
bps.
B XMT-Password mismatched.
RCV-Password mismatched.
Selective RCV incomplete.
D Transmitter received no response after it
transmitted post message, such as EOP, MPS,
EOM, etc...or received DCN.
D Transmitter received RTN after it transmitted
EOP, MPS, or EOM.
D Transmitter receives PIN after it transmitted a
post message, such as EOP, MPS, EOM, etc.
D Received DCN while waiting for post command.
(EOP, MPS, EOM, etc.)
B Received DCN after transmitting NSC.
No response within 12 seconds in NSS/DCS/
MPS wait state. (After transmitting FTT)
B No response received after transmitting 3rd
NSC.
B Remote side attempted to receive message
from your machine in polling
communication.
Inform the remote side that your machine does
not have the polling transmission feature.
D Receiver did not detect post command, such as
EOP, MPS, EOM, etc.
C Receiver returned RTN in response to post
message.
C Receiver transmitted PIN in response to PRI-Q
from transmitter. (Transmitting operator
requests voice contact)
B T1 timer (35 sec.) elapsed without detecting 300
bps signal.
B Busy Tone is detected after sending NSF Signal. Remote station disconnectes the line.
B Content of NSF (or DIS) or NSC (or DTC) was
invalid.
B DCN received to NSF/CSI/DIS transmitted.
T.30 Protocol abnormal.
Receiver working in non-CCITT mode only.
(Possible incompatibility)
"POLLED=ON" (polling XMT ready) is not set
at the transmitter.
Document to be transmitted is not placed at the
transmitter.
Receiver is defective. (Modem, LCU PCB, etc.)
SCA/SCB PCB or LCU PCB is defective.
Receiver disconnects line during first NSS (or
DCS) is transmitted.
Line quality is poor. (TCF is damaged due to
line noise)
Receiver is defective. (Modem, LCU PCB, etc.)
SCA/SCB PCB or LCU PCB is defective.
XMT, RCV password does not match.
Last 4 digits of TSI does not match with the last
4 digits of ONE-TOUCH, ABBR telephone
number.
Receiver is defective. (No paper, paper
jamming, etc.)
Receiver ceased receiving because of
excessive error. (Line quality is poor)
SCA/SCB PCB (Modem) or LCU PCB is defec-
tive.
Receiver receives data with error. (Line quality
is poor)
Receiver is defective. (Modem, LCU, etc.)
SCA/SCB PCB or LCU PCB are defective.
Receiver receives data with error due to poor
line quality, and receiving operator requests
voice contact.
Receiver is defective. (Modem, LCU, etc.)
SCA/SCB PCB or LCU PCB are defective.
Interface or line is faulty.Transmitter is
defective.
Transmitter is not ready for polling
communication.
Password does not match between transmitter
and receiver.
Transmitter is defective.
SCA/SCB PCB is defective.
Password does not match between transmitter
and receiver.
Transmitter is defective. (No document,
document jam, etc.)
Transmitter is defective.Line quality is poor.
(RTC signal is distorted due to line noise)
SCA/SCB PCB or LCU PCB are defective.
Line quality is poor. (There are excessive errors
in received data)
SCA/SCB PCB or LCU PCB are defective.
Line quality is poor. (There are excessive errors
in received data)
SCA/SCB PCB or LCU PCB are defective.
There is wrong incoming call.(non-facsimile
communication)
Transmitter is defective.
SCA/SCB PCB or LCU PCB is defective.
Wrong number is dialed.
There is an incompatibility.
The interface is incompatible.
Defective remote station.
134
Cause