Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual
  1. Manuals
  2. Brands
  3. Fujitsu Manuals
  4. Server
  5. Server PRIMERGY TX1330 M1
  6. Upgrade and maintenance manual

Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual

Hide thumbs Also See for Server PRIMERGY TX1330 M1:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operating Manual
Upgrade and Maintenance Manual - English
FUJITSU Server PRIMERGY TX1330 M1
Upgrade and Maintenance Manual
October 2014

Advertisement

Table of Contents
loading

Related Manuals for Fujitsu Server PRIMERGY TX1330 M1

Summary of Contents for Fujitsu Server PRIMERGY TX1330 M1

  • Page 1 Upgrade and Maintenance Manual - English FUJITSU Server PRIMERGY TX1330 M1 Upgrade and Maintenance Manual October 2014...

  • Page 2: Copyright And Trademarks

    – The contents of this manual may be revised without prior notice. – Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual. – No part of this manual may be reproduced in any form without the prior written permission of Fujitsu.
  • Page 3 Before reading this manual For your safety This manual contains important information for safely and correctly using this product. Carefully read the manual before using this product. Pay particular attention to the accompanying manual "Safety Notes and Regulations" and ensure these safety notes are understood before using the product.
  • Page 4 Please consult the sales staff of Fujitsu if intending to use this product for high safety use. Measures against momentary voltage drop This product may be affected by a momentary voltage drop in the power supply caused by lightning.
  • Page 5 Only for the Japanese market: Although described in this manual, some sections do not apply to the Japanese market. These options and routines include: – CSS (Customer Self Service) – USB Flash Module (UFM) Upgrade and Maintenance Manual TX1330 M1...
  • Page 6 Version history Issue number Reason for update 1.0 / August 2014 Initial release 1.1 / October 2014 Corrected cabling table Upgrade and Maintenance Manual TX1330 M1...

  • Page 7: Table Of Contents

    Content Introduction ......19 Notational conventions ....20 Before you start .
  • Page 8 Content Shutting down the server ....46 Disconnecting the server from the mains ... 46 Getting access to the component .
  • Page 9 Content Completing the maintenance task ....76 5.2.1 Updating or recovering the system board BIOS and iRMC . . . 76 5.2.1.1 Updating or recovering the system board BIOS ..77 5.2.1.2 Updating or recovering the iRMC .
  • Page 10 Content Redundant power supply ....106 6.3.1 Installing a hot-plug power supply unit ... . . 106 6.3.1.1 Preliminary steps .
  • Page 11 Content 7.2.4.1 Preliminary steps ..... . . 126 7.2.4.2 Removing a 2.5-inch HDD / SSD module ..127 7.2.4.3 Installing a 2.5-inch HDD / SSD dummy module .
  • Page 12 Content System fan and air duct ....149 Basic information ..... . . 150 Handling the fan module .
  • Page 13 Content 9.4.4 Replacing the riser card ..... 184 9.4.4.1 Preliminary steps ..... . . 184 9.4.4.2 Removing the defective riser card .
  • Page 14 Content 9.5.7 Replacing a BBU ......206 9.5.7.1 Preliminary steps ..... . 206 9.5.7.2 Removing the defective BBU .
  • Page 15 Content 11.3.2 Replacing the processor heat sink ....227 11.3.3 Concluding steps ......228 Accessible drives .
  • Page 16 Content 14.2 Replacing the CMOS battery ....254 14.2.1 Preliminary steps ......254 14.2.2 Replacing the defective CMOS battery .
  • Page 17 Content Converting a tower model to a rack model ..287 15.1 Preliminary steps ......287 15.2 Converting a tower model to a rack model .
  • Page 18 Content Upgrade and Maintenance Manual TX1330 M1...

  • Page 19: Introduction

    Introduction This Upgrade and Maintenance Manual provides instructions for the following procedures: Upgrading the server configuration by adding optional hardware ● components Upgrading the server configuration by replacing existing hardware ● components with superior ones. Replacing defective hardware components ● This manual focuses on on-site maintenance tasks.

  • Page 20: Notational Conventions

    Introduction Notational conventions The following notational conventions are used in this manual: indicates commands or menu items Text in italics indicates system output fixed font indicates text to be entered by the user semi-bold fixed font "Quotation marks" indicate names of chapters and terms that are being emphasized describes activities that must be performed in the order Ê...

  • Page 21: Before You Start

    Japanese market: http://jp.fujitsu.com/platform/server/primergy/system/ Please contact your local Fujitsu customer service partner for details on how to order expansion kits or spare parts. Use the Fujitsu Illustrated Spares Catalog to identify the required spare part and obtain technical data and order information.

  • Page 22: Classification Of Procedures

    At the beginning of each procedure, the involved unit type is indicated by one of the symbols introduced in this section. Please ask your local Fujitsu service center for more detailed information. Upgrade and Maintenance Manual...

  • Page 23: Customer Replaceable Units (Cru)

    Before you start 2.1.1 Customer Replaceable Units (CRU) Customer Replaceable Units (CRU) Customer Replaceable Units are intended for customer self service and may be installed or replaced as hot-plug components during operation. Components that the customer is entitled to replace may differ according to the service form in his country.

  • Page 24: Field Replaceable Units (Fru)

    Maintenance procedures involving Field Replaceable Units must be performed exclusively by Fujitsu service personnel or technicians trained by Fujitsu. Please note that unauthorized interference with the system will void the warranty and exempt the manufacturer from all liability. Components that are handled as Field Replaceable Units –...

  • Page 25: Average Task Duration

    Before you start – Front panel module – Management and diagnostics modules – System board – Standard power supply unit – Trusted Platform Module (TPM) – USB Flash Module (UFM) Average task duration Hardware: 10 minutes The average task duration including preliminary and concluding steps is indicated at the beginning of each procedure next to the procedure class.

  • Page 26: Tools You Need At Hand

    Before you start Step included Explanation Assembly, Reassembling the server, installing the rack installation server in the rack (if applicable) Booting time depends on hardware and Starting up software configuration and may vary significantly. Table 1: Calculation of the average task duration Tools you need at hand When preparing the maintenance task, ensure that all required tools are available according to the overview below.
  • Page 27 Before you start Screw driver / Screw Usage Type Bit insert Phillips Slimline ODD M2 x 2.5 mm PH0 / (+) No. 0 (silver) C26192-Y10-C62 TPM bit insert Dedicated TPM TPM screw REM 3 x 15 mm One way head (black) screw driver / TPM module...

  • Page 28: Documents You Need At Hand

    Important safety information, available online, or as a printed copy " 安全上のご注意 " for the Japanese market "FUJITSU Server PRIMERGY available online TX1330 M1 Operating Manual" "D3239 BIOS Setup Utility for Information on configurable BIOS options FUJITSU Server PRIMERGY and parameters, available online TX1330 M1 Reference Manual"...
  • Page 29 Management Controller" user guide Spare parts identification and information system (EMEA market only), available for online use or download (Windows OS) at Illustrated Spares catalog http://manuals.ts.fujitsu.com/illustrated_spares or from the CSS component view of the ServerView Operations Manager Glossary available online "Warranty"...
  • Page 30 Before you start Upgrade and Maintenance Manual TX1330 M1...

  • Page 31: Important Information

    Important information CAUTION! Before installing and starting up a device, please observe the safety instructions listed in the following section. This will help you to avoid making serious errors that could impair your health, damage the device and endanger the data base. Safety instructions The following safety instructions are also provided in the manual "Safety Notes and Regulations"...
  • Page 32 Important information Wait until the device has acclimatized to room temperature and is absolutely dry before starting it up. Material damage may be caused to the device if this requirement is not observed. Transport the device only in the original packaging or in packaging that ●...
  • Page 33 Important information Route the cables in such a way that they do not create a potential hazard ● (make sure no-one can trip over them) and that they cannot be damaged. When connecting the server, refer to the relevant instructions in this manual. Never connect or disconnect data transmission lines during a storm (risk of ●...
  • Page 34 Important information Devices inside the server remain hot after shutdown. Wait for a while after ● shutdown before installing or removing internal options. The circuit boards and soldered parts of internal options are exposed and ● can be damaged by static electricity. To ensure reliable protection, if you are wearing an earthing band on your wrist when working with this type of module, connect it to an unpainted, conducting metal part of the system.
  • Page 35 Important information Working with optical disk drives and media When working with optical disk drives, these instructions must be followed. CAUTION! Only use CDs/DVDs/BDs that are in perfect condition, in order to ● prevent data loss, equipment damage and injury. Check each CD/DVD/BD for damage, cracks, breakages etc.
  • Page 36 Important information Do not contaminate the CD/DVD/BD surface with fingerprints, oil, ● dust, etc. If dirty, clean with a soft, dry cloth, wiping from the center to the edge. Do not use benzene, thinners, water, record sprays, antistatic agents, or silicone-impregnated cloth. Be careful not to damage the CD/DVD/BD surface.
  • Page 37 Important information Modules with Electrostatic-Sensitive Devices Modules with electrostatic-sensitive devices are identified by the following sticker: Figure 1: ESD label When you handle components fitted with ESDs, you must always observe the following points: Switch off the system and remove the power plugs from the power outlets ●...
  • Page 38 Important information Transporting the server Only transport the server in its original packaging or in packaging that ● protects it from impacts and jolts. For the Japanese market, transporting the device in its original packaging does not apply. Do not unpack the server until it is at its installation location. ●...

  • Page 39: Energy Star

    Important information ENERGY STAR Products that have been certified compliant with ENERGY STAR and identified as such are in full compliance with the specification at shipping. Note that energy consumption can be affected by software that is installed or any changes that are made to the hardware configuration or BIOS or energy options subsequently.

  • Page 40: Fcc Class A Compliance Statement

    Consult the dealer or an experienced radio/TV technician for help. ● Fujitsu is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Fujitsu. The correction of interferences caused by such unauthorized modification, substitution or attachment will be the responsibility of the user.

  • Page 41: Environmental Protection

    Important information Environmental protection Environmentally-friendly product design and development This product has been designed in accordance with the Fujitsu standard for "environmentally friendly product design and development". This means that key factors such as durability, selection and labeling of materials, emissions, packaging, ease of dismantling and recycling have been taken into account.
  • Page 42 Details regarding the return and recycling of devices and consumables within Europe can also be found in the "Returning used devices" manual, via your local Fujitsu branch or from our recycling center in Paderborn: Fujitsu Technology Solutions Recycling Center D-33106 Paderborn Tel.

  • Page 43: Basic Hardware Procedures

    Basic hardware procedures Using diagnostics information Use the Fujitsu ServerView Suite management software to plan the upgrade or replacement of hardware components. Please refer to the following ServerView Suite topics: – Operation – Maintenance It is recommended to prepare local maintenance tasks using remote diagnostics procedures, as described in the "ServerView Suite Local Service Concept...

  • Page 44: Determining The Error Class

    Basic hardware procedures 4.1.2 Determining the error class The Local Service Concept (LSC) allows you to identify defective server components. Failure events are assigned to one of two error classes: – Global Error events that need to be resolved by maintenance personnel –...

  • Page 45: Locating The Defective Component

    Basic hardware procedures 4.1.3 Locating the defective component After determining the error class by the CSS or Global Error indicators (see section "Determining the error class" on page 44) local diagnostic indicators on the front panel, system board, HDD modules and power supply units allow you to identify the defective component (see section "Connectors and indicators"...

  • Page 46: Shutting Down The Server

    Basic hardware procedures Shutting down the server CAUTION! For further safety information, please refer to chapter "Important information" on page This step is only required when upgrading or replacing non-hot plug components. Ê Inform the system administrator that the server will be shut down and put offline.

  • Page 47: Getting Access To The Component

    Basic hardware procedures Ê Disconnect the power cord from the power supply unit and remove it from the cable tie. If you are using a redundant power supply with two power supply units, proceed with the second power supply unit in the same way. Getting access to the component CAUTION! Only valid for the tower model:...
  • Page 48 Basic hardware procedures Figure 3: Extending the server out of the rack Ê Remove all remaining external cables from the rear connector panel and expansion cards (see section "Connectors and indicators" on page 322). Ê If you are not using a cable mounting arm (CMA kit), ensure that the rear cables are long enough not to be strained or damaged when extending the server out of the rack.

  • Page 49: Removing The Server From The Rack

    Basic hardware procedures 4.4.1.2 Removing the server from the rack In most cases maintenance tasks can be performed while the server is extended from the rack. However, depending on accessibility or security guidelines, it may make sense to completely remove the server from the rack cabinet for maintenance purposes.
  • Page 50 Basic hardware procedures Figure 4: Removing the server from the rack Ê Release the locking bars on both rails (1). Ê Lift up the front of the server as shown so that the front and middle rack mounting bolts are disengaged from the mounting points on the telescopic rails (2).

  • Page 51: Removing The Top Cover

    Basic hardware procedures 4.4.1.3 Removing the top cover Figure 5: Removing the top cover (rack server) Ê Open the locking lever (1). This will slide the top cover back disengaging the locking mechanism (2). Ê Remove the top cover (3). Upgrade and Maintenance Manual TX1330 M1...

  • Page 52: Removing The Rack Front Cover

    Basic hardware procedures 4.4.1.4 Removing the rack front cover You remove the rack front cover when installing/removing accessible drives. Figure 6: Removing the ID card (rack server) Ê Remove the ID card from the server. Figure 7: Removing the rack front cover (A) Ê...

  • Page 53: Tower Model

    Basic hardware procedures Figure 8: Removing the rack front cover (B) Ê Carefully fold down and unhook the rack front cover (1). Ê Detach and remove the rack front cover from the chassis (2). 4.4.2 Tower model 4.4.2.1 Removing the side cover Figure 9: Unlocking the server Upgrade and Maintenance Manual TX1330 M1...
  • Page 54 Basic hardware procedures Ê Insert the key into the lock on the server front. Ê Turn the key clockwise to unlock the front and side covers (1). Ê Remove the key from the server front (2) and set aside for later use. Figure 10: Removing the side cover (tower server) Ê...

  • Page 55: Removing The Hdd Bay Cover

    Basic hardware procedures 4.4.2.2 Removing the HDD bay cover Figure 11: Removing the HDD cover Ê Unlock the server (1). Ê Pull out on the handle on the upper edge of the HDD bay cover. Ê Fold out and remove the HDD bay cover from the front cover. Upgrade and Maintenance Manual TX1330 M1...

  • Page 56: Removing The Front Cover

    Basic hardware procedures 4.4.2.3 Removing the front cover You remove the front cover when: – installing/removing accessible drives – converting a tower model to a rack model Figure 12: Removing the ID card (tower server) Ê Remove the ID card from the server front. It may be necessary to pull out on the ID card rather firmly.
  • Page 57 Basic hardware procedures Figure 13: Removing the front cover (tower server) Ê Pinch the locking clips to disengage the front cover (1) while slightly pulling out. Ê Carefully fold out the bottom end of the front cover (2). Ê Unhook and remove the front cover (3). Upgrade and Maintenance Manual TX1330 M1...

  • Page 58: Reassembling

    Basic hardware procedures Reassembling CAUTION! Before attaching the covers, make sure no unnecessary parts or tools ● are left inside the server. In order to comply with applicable EMC regulations (regulations on ● electromagnetic compatibility) and satisfy cooling requirements, the server must not run while the top / side cover is removed.

  • Page 59: Installing The Top Cover

    Basic hardware procedures Ê Secure the rack front cover to the chassis with two screws on either side (see figure 7 on page 52). Ê Insert and slide the ID card into its slot until it locks in place (see close-up in figure 6 on page 52).

  • Page 60: Mounting The Server In The Rack

    Basic hardware procedures 4.5.1.3 Mounting the server in the rack CAUTION! At least two people are needed to position the server on the rack rails. (For the Japanese market, please refer to " 安全上のご注意 ".) For configurations below 32 kg: At least two people are needed to lift the server into the rack cabinet.
  • Page 61 Basic hardware procedures Figure 16: Mounting the server onto the rack rails CAUTION! Ensure that the safety lock has been properly inserted into the snap fit lock. For further information, refer to the "Rack Mounting Kit - RMK-F2 Drop-In" Mounting Instructions. Ê...

  • Page 62: Sliding The Server Into The Rack

    Basic hardware procedures 4.5.1.4 Sliding the server into the rack Figure 17: Sliding the server into the rack Ê Pull up on the locking latch on both telescopic rails (1). Ê Slide the server inside the rack as far as it will go (2) until the quick release levers lock into place.

  • Page 63: Tower Model

    Basic hardware procedures 4.5.2 Tower model 4.5.2.1 Installing the front cover Figure 18: Installing the front cover (tower server) (A) Ê Hook the two tabs of the front cover into the notches in the chassis. Figure 19: Installing the front cover (tower server) (B) Ê...

  • Page 64: Installing The Hdd Bay Cover

    Basic hardware procedures Ê Insert and slide the ID card into its slot until it locks in place (see figure 12 on page 56.) 4.5.2.2 Installing the HDD bay cover Figure 20: Installing the HDD bay cover Ê Insert the HDD bay cover into the front cover as shown (1). Ê...

  • Page 65: Installing The Side Cover

    Basic hardware procedures 4.5.2.3 Installing the side cover Figure 21: Installing the side cover (tower server) Ê Open the locking lever on the side cover. Ê Fit the side cover on the chassis, recessed by 2 cm (1). Ê Close the locking lever on the side cover (2). This will slide the top cover shut engaging the locking mechanism (3).

  • Page 66: Locking The Server

    Basic hardware procedures 4.5.2.4 Locking the server Figure 22: Locking the server Ê If required by security regulations, insert the key into the lock on the front panel and lock the server. Upgrade and Maintenance Manual TX1330 M1...

  • Page 67: Connecting The Server To The Mains

    Basic hardware procedures Connecting the server to the mains CAUTION! The power supply automatically adjusts to any mains voltage in the range of 100 V - 240 V. You may only operate the server if its rated voltage range corresponds to the local mains voltage. Ê...

  • Page 68: Switching On The Server

    Basic hardware procedures Switching on the server CAUTION! Before switching on the server, make sure the top / side cover is ● closed. In order to comply with applicable EMC regulations (regulations on electromagnetic compatibility) and satisfy cooling requirements, the server must not run while the top / side cover is removed.

  • Page 69: Basic Software Procedures

    Basic software procedures Starting the maintenance task 5.1.1 Disabling BitLocker functionality BitLocker Drive Encryption provides protection for operating system and data drives by encrypting the contents and requiring users to authenticate their credentials to access the information. On the operating system drive, BitLocker uses the compatible Trusted Platform Module (TPM) to detect if the computer's startup process has been modified from its original state.

  • Page 70: Disabling Svom Boot Watchdog Functionality

    BitLocker setup wizard, modify the BitLocker Group Policy settings. For further information on how to disable BitLocker drive encryption, please refer to the Microsoft Knowledge Base. Fujitsu service partners will find additional information (also available in Japanese) on the Fujitsu Extranet web pages. 5.1.2...

  • Page 71: Configuring Boot Watchdog Settings

    Basic software procedures Ê Under Watchdog Settings, you can obtain detailed information about the current watchdog status, time out intervals and actions that are triggered if watchdog time outs are exceeded. For detailed information on iRMC settings, refer to the "Integrated Remote Management Controller"...

  • Page 72: Removing Backup And Optical Disk Media

    For further information on "forcible" tape ejection, please refer to the "Tape Facts" guide available to Fujitsu service partners from the following https address: https://partners.ts.fujitsu.com/com/service/ps/Servers/PRIMERGY/Pages/ TapeFacts.aspx...

  • Page 73: Verifying And Configuring The Backup Software Solution

    Procedures may differ depending on the backup software. For details, refer to the dedicated documentation provided separately. Further information on suitable backup software solutions and related documentation is available to Fujitsu service partners from the Fujitsu Extranet pages. 5.1.5 Note on server maintenance in a Multipath I/O...
  • Page 74 Basic software procedures Ê Burn the image to a DVD. Ê In order to create a bootable USB stick, please proceed as described in the "Local System Update for PRIMERGY Servers" user guide. Ê Before using the ServerView Update DVD or USB stick in an offline environment, properly shut down the server and disconnect all external I/O connections (like LAN or FC cables) from the system.
  • Page 75 Basic software procedures Using PrimeCollect To start PrimeCollect, proceed as follows: Ê Before using PrimeCollect in an offline environment, properly shut down the server and disconnect all external I/O connections (like LAN or FC cables) from the system. Only keep mouse, keyboard, video cable and AC power cord connected.

  • Page 76: Switching On The Id Indicator

    After replacing the system board, memory or a CPU, it is essential to upgrade the BIOS and iRMC to the latest version. The latest BIOS and iRMC versions are available from the Fujitsu support internet pages at: http://ts.fujitsu.com/support/ (EMEA market) (Japanese market) http://jp.fujitsu.com/platform/server/primergy/downloads/...

  • Page 77: Updating Or Recovering The System Board Bios

    Basic software procedures Fujitsu does not assume responsibility for any damage done to the server or for the loss of any data resulting from BIOS updates. 5.2.1.1 Updating or recovering the system board BIOS BIOS flash procedure Ê Perform the BIOS flash procedure as described in your server’s "BIOS Setup Utility"...
  • Page 78 Ê Press the Power On / Off button. The system starts the POST process. In iRMC recovery mode, the “FUJITSU” logo does not show up. Ê The system will detect the USB stick.

  • Page 79: Verifying System Information Backup / Restore

    Basic software procedures If the iRMC does not work after flashing, disconnect the system from the mains and reconnect it again. Ê Shut down the server by pressing the power On / Off button. Ê Disconnect the server from the mains to exit the iRMC recovery state. 5.2.2 Verifying system information backup / restore To avoid the loss of non-default settings when replacing the system board, a...

  • Page 80: Updating Raid Controller Firmware

    "Local System Update for PRIMERGY Servers" user guide Using the flash tool The latest firmware files are available as ASPs (Autonomous Support Packages) for Windows or as DOS tools from the Fujitsu support web pages at: (EMEA market) http://ts.fujitsu.com/support/ http://jp.fujitsu.com/platform/server/primergy/downloads/ (Japanese market) Ê...

  • Page 81: Enabling Option Rom Scan

    Basic software procedures 5.2.4 Enabling Option ROM scan In order to configure an expansion card that has been installed or replaced, the card’s Option ROM has to be enabled in the system board BIOS. The card’s firmware is called by the system BIOS upon reboot and can be entered and configured.

  • Page 82: Resetting The Boot Retry Counter

    Procedures may differ depending on the backup software. For details, refer to the dedicated documentation provided separately. Further information on suitable backup software solutions and related documentation is available to Fujitsu service partners from the Fujitsu Extranet pages. Re-enabling backup drives...

  • Page 83: Resetting The Boot Retry Counter

    Basic software procedures Ê Select the Server Mgmt menu. Ê Under Boot Retry Counter the current number of remaining boot attempts is displayed. The value is further decremented with every failed boot attempt or system reboot resulting from critical system errors. Ê...

  • Page 84: Enabling Svom Boot Watchdog Functionality

    Basic software procedures Resetting the boot retry counter using iRMC web frontend Ê Enter the ServerView iRMC web frontend. Ê Select the Server Management menu. Ê The following boot retry counter settings are available under ASR&R Options: Ê Under Retry counter max specify the maximum number of attempts to boot the operating system (0 to 7).

  • Page 85: Enabling Replaced Components In The System Bios

    Basic software procedures Ê Under Watchdog Settings ensure that the check box next to Boot Watchdog is selected. From the drop down list choose Reset and specify the desired timeout delay. Ê Click Apply for the changes to take effect. For detailed information on iRMC settings, refer to the "Integrated Remote Management Controller"...

  • Page 86: Verifying The System Time Settings

    Basic software procedures For detailed information on memory operation modes available for your server, refer to section "Memory sequence" on page 210. After replacing the defective module(s) the memory operation mode is automatically reset to its original state. It is recommended to verify that the operation mode has been correctly.

  • Page 87: Viewing And Clearing The System Event Log (Sel)

    Basic software procedures Ê Save your changes and exit the BIOS. For detailed information on how to access the BIOS and modify settings, refer to the corresponding BIOS Setup Utility reference manual 5.2.11 Viewing and clearing the System Event Log (SEL) 5.2.11.1 Viewing the SEL You can view the System Event Log (SEL) using the ServerView Operations Manager or the ServerView iRMC web frontend:...

  • Page 88: Clearing The Sel

    Basic software procedures Viewing the SEL using the iRMC web frontend Ê Enter the ServerView iRMC web frontend. Ê Select the Event Log and choose the Internal Event Log submenu. Ê Under Internal Event Log Content the SEL is being displayed. In order to filter the list, select the check boxes next to the desired event types and press Apply for the changes to take effect.
  • Page 89 Basic software procedures Procedures may differ depending on your Linux OS or the definition file on the client system. Use the following information as reference. Ask the system administrator to change the definition file. Ê After replacing a network controller or the system board, switch on and boot the server as described in section "Switching on the server"...

  • Page 90: Enabling Bitlocker Functionality

    For further information on how to enable BitLocker drive encryption, please refer to the Microsoft Knowledge Base. Fujitsu service partners will find additional information (also available in Japanese) on the Fujitsu Extranet web pages. 5.2.14 Performing a RAID array rebuild...

  • Page 91: Looking Up Changed Mac / Wwn Addresses

    Basic software procedures Ê Inform the customer about the remaining rebuild time, based on the displayed duration estimate. Figure 24: Progress bar (RAID array rebuild) CAUTION! The system is now operational, however, data redundancy will not be available until the RAID array rebuild is complete. Depending on the hard disk drive capacity the overall process can take up to several hours, in some cases even days.

  • Page 92: Looking Up Wwn Addresses

    Basic software procedures 5.2.15.2 Looking up WWN addresses Emulex FC / FCoE adapters Ê Enable the network controller’s Option ROM in the system board BIOS as described in section "Enabling Option ROM scan" on page Ê Restart the server. Ê During boot, as soon as the Emulex BIOS utility option appears, press [ALT]+[E] or [CTRL]+[E].

  • Page 93: Using The Chassis Id Prom Tool

    After replacing the Chassis ID EPROM, system information has to be entered using the Chassis ID Prom tool. The tool and further instructions are available to maintenance personnel from the Fujitsu Technology Solutions Extranet: https://partners.ts.fujitsu.com/com/service/ps/Servers/PRIMERGY/ Ê Select your PRIMERGY system from the main area of the page.

  • Page 94: After Replacing / Upgrading Lan Controllers

    Basic software procedures 5.2.17.1 After replacing / upgrading LAN controllers Please note when re-using a replaced LAN controller: Ê Confirm with the customer whether the LAN controller you have replaced has been used as part of a LAN teaming configuration. Ê...

  • Page 95: Specifying The Chassis Model

    On Windows-based servers with ServerView agents installed, proceed as follows: Ê Click Start, point to All Programs, and then point to Fujitsu - ServerView Suite - Agents - Maintenance Tools. Ê In the Maintenance Tools menu pane, click the Chassis Model Configuration tab.

  • Page 96: Performing A Fan Test After Replacing A Defective Fan

    Basic software procedures For more detailed information on installing ServerView agents, refer to the "ServerView Operations Manager - Installation ServerView Agents for Windows" user guide. 5.2.20 Performing a fan test after replacing a defective fan After replacing a defective system fan or power supply unit containing a defective fan, the fan error indicators will stay lit until the next fan test.
  • Page 97 Basic software procedures Ê After the fan test is complete, restore the time setting to its initial value and click Save Page. For more detailed information, refer to the "ServerView Operations Manager" user guide. For the Japanese market: Executing the fan test via Chassis ID Prom Tool Please follow the instructions provided separately.
  • Page 98 Basic software procedures Upgrade and Maintenance Manual TX1330 M1...

  • Page 99: Power Supply

    Power supply Safety notes CAUTION! Do not disassemble the power supply unit. Doing so may cause ● electric shock. Areas around the power supply unit may remain extremely hot after ● shutdown. After shutting down the server, wait for hot components to cool down before removing the power supply unit.

  • Page 100: Standard Power Supply

    Power supply Standard power supply 6.2.1 Replacing the standard power supply unit Field Replaceable Unit Hardware: 10 minutes (FRU) Tools: Phillips PH2 / (+) No. 2 screw driver 6.2.1.1 Preliminary steps "Disabling BitLocker functionality" on page 69 Ê "Locating the defective server" on page 43 Ê...

  • Page 101: Removing The Defective Standard Power Supply Unit

    Power supply 6.2.1.2 Removing the defective standard power supply unit Figure 25: Disconnecting power cables (A) Ê Open the power cable clamp (1). Ê While pressing the release latch on the connector, disconnect the ATX power supply connector (2). Figure 26: Disconnecting power cables (B) Ê...
  • Page 102 Power supply Figure 27: Detaching the standard power supply unit Ê Remove the five screws (see circles). Figure 28: Taking out the standard power supply unit Ê Slide the power supply unit inside the chassis by 3 cm (1). Ê Lift the power supply unit out of the chassis (2). Upgrade and Maintenance Manual TX1330 M1...
  • Page 103 Power supply Figure 29: Removing the installation frame from the power supply unit (A) Ê Remove the two screws (see circles). Figure 30: Removing the installation frame from the power supply unit (B) Ê Remove the installation frame from the power supply unit. Upgrade and Maintenance Manual TX1330 M1...

  • Page 104: Installing The New Standard Power Supply Unit

    Power supply 6.2.1.3 Installing the new standard power supply unit Figure 31: Attaching the installation frame to the power supply unit Ê Attach the installation frame to the power supply unit. Figure 32: Securing the installation frame to the power supply unit Ê...
  • Page 105 Power supply Figure 33: Installing the standard power supply unit Ê Lower the power supply unit into the chassis so that the two hooks on the server floor (see close-up) rest in the recesses in the installation frame (1). Ê Slide the power supply unit towards the rear of the chassis (2). Ê...

  • Page 106: Concluding Steps

    Power supply 6.2.1.4 Concluding steps "Installing the fan module" on page 152 Ê "Reassembling" on page 58 Ê "Connecting the server to the mains" on page 67 Ê "Switching on the server" on page 68 Ê "Enabling BitLocker functionality" on page 90 Ê...

  • Page 107: Removing The Dummy Cover

    Power supply 6.3.1.2 Removing the dummy cover Figure 34: Removing the dummy cover Ê Press in on both release latches (1) and remove the dummy cover (2). CAUTION! Keep the dummy cover for future use. If a power supply unit is removed and not immediately replaced by a new one, a dummy cover must be reinstalled in the bay to comply with applicable EMC regulations and satisfy cooling requirements.

  • Page 108: Installing A Hot-Plug Power Supply Unit

    Power supply 6.3.1.3 Installing a hot-plug power supply unit Figure 35: Installing a power supply unit Ê Push the power supply unit into its slot (1) as far as it will go until the locking latch snaps in place (2). CAUTION! Ensure that the power supply unit properly engages in its slot and is locked in position in order to prevent it from sliding out of the chassis...

  • Page 109: Removing A Hot-Plug Power Supply Unit

    Power supply 6.3.2 Removing a hot-plug power supply unit Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less Note for servers using CMA (Cable Management Arm) Regarding of removing power supply units, additional tasks are needed, due to an interference between CMA stopper and the power supply units. Ê...

  • Page 110: Removing A Hot-Plug Power Supply Unit

    Power supply 6.3.2.2 Removing a hot-plug power supply unit Figure 36: Removing a power supply unit Ê Fold up the handle on the power supply unit (1). Ê Press in on the green release latch (2). Ê While keeping the green release latch pressed, pull the power supply unit out of its bay (3).

  • Page 111: Installing The Dummy Cover

    Power supply 6.3.2.3 Installing the dummy cover Figure 37: Installing the dummy cover Ê Insert the dummy cover into the empty bay with the impressed arrow symbol facing to the left (see circle). Ê Push the dummy cover into its bay until it locks in place. CAUTION! Always install dummy covers into unused bays to comply with applicable EMC regulations and satisfy cooling requirements.

  • Page 112: Preliminary Steps

    Power supply Note for servers using CMA (Cable Management Arm) Regarding of replacing power supply units, additional tasks are needed, due to an interference between CMA stopper and the power supply units. Ê Unlock the CMA stopper. Ê Remove the CMA stopper with the mounted crossbar. Ê...

  • Page 113: Concluding Steps

    Power supply 6.3.3.4 Concluding steps Ê Connect the power cord to the new power supply unit and secure it with a cable tie as described in section "Connecting the server to the mains" on page Ê Only when replacing a power supply unit in a non-redundant configuration: "Switching on the server"...

  • Page 114: Replacing The Defective Power Distribution Board

    Power supply 6.3.4.3 Replacing the defective power distribution board Figure 38: Disconnecting power cables Ê Disconnect the two power cables from the power distribution board. Upgrade and Maintenance Manual TX1330 M1...

  • Page 115: Installing The Hot-Plug Power Supply Units

    Power supply Figure 39: Replacing the power distribution board Ê Loosen the captive screw (1). Ê Push the power distribution board in direction of the arrow (2). Ê Remove the power distribution board (3). Ê Insert the new power distribution board in the PSU cage (4). Ê...

  • Page 116: Concluding Steps

    Power supply 6.3.4.5 Concluding steps "Installing the fan module" on page 152 Ê "Reassembling" on page 58 Ê "Connecting the server to the mains" on page 67 Ê "Switching on the server" on page 68 Ê "Enabling BitLocker functionality" on page 90 Ê...

  • Page 117: Removing The Standard Power Supply Unit

    Power supply 6.4.2 Removing the standard power supply unit Ê Remove the standard power supply unit as described in section "Removing the defective standard power supply unit" on page 101. 6.4.3 Installing the upgrade kit Figure 40: Installing the PSU cage Ê...
  • Page 118 Power supply Figure 41: Securing the PSU cage Ê Secure the PSU cage to the chassis with five screws (see circles) Figure 42: Connecting power cables to the system board Ê Connect the black power connector to system board connector "P30" (1) (see figure 203 on page 304).

  • Page 119: Concluding Steps

    Power supply Ê Connect the power connector P1 to system board connector "PWR1" (2) (see section "Cabling plans" on page 303). Ê Route the power cables in the corresponding cable clamps (see circles). Ê Install the power supply unit(s) as described in "Installing a hot-plug power supply unit"...
  • Page 120 Power supply Upgrade and Maintenance Manual TX1330 M1...

  • Page 121: Hard Disk Drives / Solid State Drives

    Hard disk drives / solid state drives Safety notes CAUTION! The hard disk drive must not be removed from the installation frame ● by anyone except a service technician. HDD / SSD modules must all be marked clearly so that they can be ●...

  • Page 122: Basic Information

    Hard disk drives / solid state drives Basic information – Please refer to section "2.5-inch HDD / SSD configurations" on page 123 and section "3.5-inch HDD configurations" on page 133 for a complete overview of the mounting sequences. – Install dummy modules into unused HDD / SSD bays. Upgrade and Maintenance Manual TX1330 M1...

  • Page 123: Inch Hdd / Ssd Configurations

    Hard disk drives / solid state drives 2.5-inch HDD / SSD configurations 7.2.1 Mounting order Maximum configuration: 8x 2.5-inch HDDs / SSDs Figure 43: 2.5-inch HDD / SSD mounting order (example tower server) 7.2.2 HDD / SSD naming scheme The HDD / SSD numbering as listed in the ServerView RAID Manager differs from the HDD mounting order: 2.5-inch HDDs / SSDs RAID...

  • Page 124: Installing 2.5-Inch Hdd / Ssd Modules

    Hard disk drives / solid state drives 7.2.3 Installing 2.5-inch HDD / SSD modules Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less 7.2.3.1 Preliminary steps Ê If applicable, "Removing the HDD bay cover" on page 55 Ê Locate the correct drive bay as described in section "2.5-inch HDD / SSD configurations"...

  • Page 125: Installing A 2.5-Inch Hdd / Ssd Module

    Hard disk drives / solid state drives 7.2.3.3 Installing a 2.5-inch HDD / SSD module Figure 45: Opening the 2.5-inch HDD / SSD module locking lever Ê Pinch the green locking clips (1) and open the locking lever (2). Figure 46: Inserting the 2.5-inch HDD / SSD module Ê...

  • Page 126: Concluding Steps

    Hard disk drives / solid state drives 7.2.3.4 Concluding steps Ê If applicable, "Installing the HDD bay cover" on page 64 "Performing a RAID array rebuild" on page 90 Ê 7.2.4 Removing 2.5-inch HDD / SSD modules Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less...

  • Page 127: Removing A 2.5-Inch Hdd / Ssd Module

    Hard disk drives / solid state drives In order to permanently remove an operational HDD module that is part of a RAID array from the server, you first need to delete the array using ServerView RAID Manager. CAUTION! All data on all HDDs / SSDs in the array will be lost! Be sure to back up your data before deleting a RAID array.

  • Page 128: Installing A 2.5-Inch Hdd / Ssd Dummy Module

    Hard disk drives / solid state drives 7.2.4.3 Installing a 2.5-inch HDD / SSD dummy module CAUTION! If the removed HDD / SSD module is not replaced immediately, always replace a dummy module into the unused HDD / SSD bay to comply with applicable EMC regulations and satisfy cooling requirements.

  • Page 129: Replacing A 2.5-Inch Hdd / Ssd Module

    Hard disk drives / solid state drives 7.2.5 Replacing a 2.5-inch HDD / SSD module Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less CAUTION! Only remove an HDD / SSD module during operation if the drive is ● not currently being accessed. Observe the indicators on the HDD / SSD module, as described in the operating manual of your server.

  • Page 130: Removing A 2.5-Inch Hdd / Ssd Module

    Hard disk drives / solid state drives 7.2.5.2 Removing a 2.5-inch HDD / SSD module Ê Remove the HDD / SSD module to be replaced from the server as described in section "Removing a 2.5-inch HDD / SSD module" on page 127.

  • Page 131: Removing The Defective 2.5-Inch Hdd Sas / Sata Backplane

    Hard disk drives / solid state drives 7.2.6.2 Removing the defective 2.5-inch HDD SAS / SATA backplane Figure 49: Disconnecting cables Ê Disconnect the power cable (1) and the SAS / SATA cable (2) from the desired SAS / SATA backplane. Ê...

  • Page 132: Installing The New 2.5-Inch Hdd Sas / Sata Backplane

    Hard disk drives / solid state drives 7.2.6.3 Installing the new 2.5-inch HDD SAS / SATA backplane Figure 51: Installing the SAS / SATA backplane Ê At a slight angle, fit the SAS / SATA backplane into the two guides on the drive cage (1).

  • Page 133: Inch Hdd Configurations

    Hard disk drives / solid state drives 3.5-inch HDD configurations 7.3.1 Mounting order Maximum configuration: 4x 3.5-inch HDDs Figure 52: 3.5-inch HDD mounting order (example tower server) 7.3.2 HDD naming scheme 3.5-inch HDDs RAID RAID log. log. Manager Channel Manager Channel Drive # Drive #...

  • Page 134: Preliminary Steps

    Hard disk drives / solid state drives Tools: tool-less 7.3.3.1 Preliminary steps Ê If applicable, "Removing the HDD bay cover" on page 55 Ê Locate the correct drive bay as described in section "3.5-inch HDD configurations" on page 133. 7.3.3.2 Removing a 3.5-inch HDD dummy module Figure 53: Removing a 3.5-inch dummy module Ê...

  • Page 135: Installing A 3.5-Inch Hdd Module

    Hard disk drives / solid state drives CAUTION! Save the dummy module for future use. Always replace dummy modules into unused HDD bays to comply with applicable EMC regulations and satisfy cooling requirements. 7.3.3.3 Installing a 3.5-inch HDD module Figure 54: Opening the 3.5-inch HDD module locking lever Ê...

  • Page 136: Concluding Steps

    Hard disk drives / solid state drives Figure 55: Inserting the 3.5-inch HDD module Ê Insert the HDD module into a drive bay and carefully push back as far as it will go (1). Ê Fold down the lever to lock the HDD module in place (2). 7.3.3.4 Concluding steps Ê...

  • Page 137: Removing 3.5-Inch Hdd Modules

    Hard disk drives / solid state drives 7.3.4 Removing 3.5-inch HDD modules Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less 7.3.4.1 Preliminary steps Ê If the HDD module to be removed is combined into a RAID array, please proceed as follows: RAID level Procedure Only remove an HDD module combined in a RAID 0 array if...

  • Page 138: Removing A 3.5-Inch Hdd Module

    Hard disk drives / solid state drives For further information, please refer to the "ServerView Suite RAID Management" user guide. Ê If applicable, "Removing the HDD bay cover" on page 55 7.3.4.2 Removing a 3.5-inch HDD module Figure 56: Removing a 3.5-inch HDD module Ê...

  • Page 139: Installing A 3.5-Inch Hdd Dummy Module

    Hard disk drives / solid state drives 7.3.4.3 Installing a 3.5-inch HDD dummy module CAUTION! If the removed HDD module is not replaced immediately, always replace a dummy module into the unused HDD bay to comply with applicable EMC regulations and satisfy cooling requirements. Figure 57: Installing a 3.5-inch HDD dummy module Ê...

  • Page 140: Replacing A 3.5-Inch Hdd Module

    Hard disk drives / solid state drives 7.3.5 Replacing a 3.5-inch HDD module Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less CAUTION! Only remove an HDD module during operation if the drive is not ● currently being accessed. Observe the indicators on the HDD module, as described in the operating manual of your server.

  • Page 141: Removing A 3.5-Inch Hdd Module

    Hard disk drives / solid state drives 7.3.5.2 Removing a 3.5-inch HDD module Ê Remove the HDD module to be replaced from the server as described in section "Removing a 3.5-inch HDD module" on page 138. 7.3.5.3 Installing a 3.5-inch HDD module Ê...

  • Page 142: Removing The Defective 3.5-Inch Hdd Sas Backplane

    Hard disk drives / solid state drives 7.3.6.2 Removing the defective 3.5-inch HDD SAS backplane Figure 58: Disconnecting cables Ê Disconnect the cables from the SAS backplane: – (1) power cable from connector "x7" – (2) SAS/SATA data cable from connector "x1" Upgrade and Maintenance Manual TX1330 M1...
  • Page 143 Hard disk drives / solid state drives Figure 59: Removing the 3.5-inch HDD bay top cover (A) Ê Remove five screws from the 3.5-inch HDD bay top cover (see blue arrows). Ê Remove one screw from the intrusion switch holder (see orange arrow). Figure 60: Removing the 3.5-inch HDD bay top cover (B) Ê...
  • Page 144 Hard disk drives / solid state drives Figure 61: Removing the 3.5-inch HDD bay top cover (C) Ê Carefully fold up the 3.5-inch HDD bay top cover to disengage it from the SAS backplane below (1). Ê Remove the 3.5-inch HDD bay top cover from the chassis (2). Figure 62: Removing the 3.5-inch HDD SAS backplane Ê...

  • Page 145: Installing The New 3.5-Inch Hdd Sas Backplane

    Hard disk drives / solid state drives 7.3.6.3 Installing the new 3.5-inch HDD SAS backplane Figure 63: Installing the 3.5-inch HDD SAS backplane Ê Fit the SAS backplane into the guide on the outer wall of the HDD bay and lower it into the bottom rim (see close-up).
  • Page 146 Hard disk drives / solid state drives Figure 64: Installing the 3.5-inch HDD bay top cover (A) Ê At a slight angle, fit the HDD bay top cover under the front chassis rim (1). Ê Fold down the HDD bay top cover (2) until it is properly seated on the HDD bays.
  • Page 147 Hard disk drives / solid state drives Ê Slide the intrusion switch holder under the front chassis rim as far as it will go (2). Figure 66: Installing the 3.5-inch HDD bay top cover (C) Ê Secure the HDD bay top cover to the chassis with five screws (see blue arrows).

  • Page 148: Connecting The 3.5-Inch Hdd Sas Backplane

    Hard disk drives / solid state drives 7.3.6.4 Connecting the 3.5-inch HDD SAS backplane Figure 67: Connecting cables Ê Connect the cables to the SAS backplane: – (1) power cable to connector "x7" – (2) SAS/SATA data cable to connector "x1" 7.3.6.5 Concluding steps Ê...

  • Page 149: System Fan And Air Duct

    System fan and air duct Safety notes CAUTION! Do not damage or modify internal cables or devices. Doing so may ● cause a device failure, fire, or electric shock. Devices and components inside the server remain hot after ● shutdown. After shutting down the server, wait for hot components to cool down before installing or removing internal options.

  • Page 150: Basic Information

    System fan and air duct Basic information Figure 68: Fan module Air duct System fan 120 x 38 mm The fan module consists of the system fan contained in an air duct directing airflow directly onto the CPU heat sink and memory slots. Additional fans in power supply units are integral parts of the power supply units and cannot be replaced separately.

  • Page 151: Handling The Fan Module

    System fan and air duct Handling the fan module Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 8.2.1 Preliminary steps "Shutting down the server" on page 46 Ê "Disconnecting the server from the mains" on page 46 Ê "Getting access to the component"...

  • Page 152: Installing The Fan Module

    System fan and air duct Ê Push the locking tab (2) inside while slightly lifting up the fan module to disengage the retaining brackets on the server rear. Ê Lift the fan module out of the chassis (3). 8.2.3 Installing the fan module Figure 70: Installing the fan module Ê...

  • Page 153: Concluding Steps

    System fan and air duct 8.2.4 Concluding steps "Reassembling" on page 58 Ê "Connecting the server to the mains" on page 67 Ê "Switching on the server" on page 68 Ê Replacing the system fan Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 8.3.1...

  • Page 154: Removing The Defective System Fan

    System fan and air duct 8.3.2 Removing the defective system fan Figure 71: Removing the fan cable from the guidings Ê Remove the fan cable from the guidings. Upgrade and Maintenance Manual TX1330 M1...
  • Page 155 System fan and air duct Figure 72: Removing the safety pins from the snap rivets Ê Remove the safety pins (see circles) from the four snap rivets on the air duct. Upgrade and Maintenance Manual TX1330 M1...
  • Page 156 System fan and air duct Figure 73: Removing the system fan from the air duct Ê Pull the system fan from the snap rivets (1). Ê Remove the system fan from the air duct (2). Upgrade and Maintenance Manual TX1330 M1...

  • Page 157: Installing The New System Fan

    System fan and air duct 8.3.3 Installing the new system fan Ê Insert the system fan into the air duct. Figure 74: Installing the system fan in the air duct Ê Push the system fan on the snap rivets (1). Notice the position of the fan cable.
  • Page 158 System fan and air duct Upgrade and Maintenance Manual TX1330 M1...

  • Page 159: Expansion Cards And Backup Units

    Expansion cards and backup units Safety notes CAUTION! Do not damage or modify internal cables or devices. Doing so may ● cause a device failure, fire, or electric shock. Devices and components inside the server remain hot after ● shutdown. After shutting down the server, wait for hot components to cool down before installing or removing internal options.

  • Page 160: Basic Information

    Expansion cards and backup units Basic information The system board is equipped with four expansion slots. slot 4 slot 3 slot 2 slot 1 Figure 75: PCI slot overview PCI slot Type Function PCe Gen2 x1 slot for optional PCI adapter board (connected (mechanical x4) with riser card) PCIe Gen 2 x4...
  • Page 161 Riser Card for 32-bit PCI cards with PCI adapter board For the latest information on supported expansion cards, refer to your server’s hardware configurator available online at the following address: for the EMEA market: http://ts.fujitsu.com/products/standard_servers/index.htm for the Japanese market: http://jp.fujitsu.com/platform/server/primergy/system/ Upgrade and Maintenance Manual TX1330 M1...

  • Page 162: Handling Slot Brackets

    Expansion cards and backup units Handling slot brackets 9.2.1 Installing a slot bracket Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: Phillips PH2 / (+) No. 2 screw driver Use the following slot bracket for the ModularRAID controllers based on LSI MegaRAID: –...
  • Page 163 Expansion cards and backup units Installing the slot bracket Figure 77: Installing the PCI slot bracket (A) Ê Place the controller on the mounting tabs on the slot bracket. Ê Carefully shift the slot bracket towards the controller until the plug shells engage with the cut-outs in the slot bracket connector panel.
  • Page 164 Expansion cards and backup units Example network adapter D2755 Figure 79: Network adapter D2755 - Mounting the slot bracket (A) Ê Place the controller on the mounting tabs on the slot bracket (1). Ê Carefully shift the slot bracket towards the controller until the plug shells engage with the cut-outs in the slot bracket connector panel (2).
  • Page 165 Expansion cards and backup units Figure 81: Network adapter D2755 - Mounting the slot bracket (C) Assembled network adapter D2755 Example network adapter D3035 Figure 82: Placing the slot bracket - D3035 Ê Place the controller on the mounting tabs on the slot bracket (1). Ê...
  • Page 166 Expansion cards and backup units Figure 83: Fastening the slot bracket - D3035 Ê Secure the slot bracket to the controller with two M3 x 4.5 mm screws. Figure 84: Assembled network adapter D3035 Upgrade and Maintenance Manual TX1330 M1...
  • Page 167 Expansion cards and backup units Example network adapter D3045 Figure 85: Placing the slot bracket - D3045 Ê Hinge the slot bracket to the plug shell as shown (1). Ê Fold the slot bracket towards the controller until the threaded mounting tab is aligned with the screw hole on the controller (2).

  • Page 168: Removing A Slot Bracket

    Expansion cards and backup units Figure 87: Assembled network adapter D3045 9.2.2 Removing a slot bracket Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: Phillips PH2 / (+) No. 2 screw driver Removing the slot bracket Ê Remove the two screws. Ê...

  • Page 169: Handling Sfp+ Transceiver Modules

    Expansion cards and backup units Handling SFP+ transceiver modules For Fiber Channel over Ethernet (FCoE) configurations, the Ethernet server adapter is equipped with one or two SFP+ (small form-factor pluggable) transceiver modules. 9.3.1 Installing SFP+ transceiver modules Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less...
  • Page 170 Expansion cards and backup units Figure 89: Unlatching the locking bail Ê Carefully unlatch and fold down the locking bail on the SFP+ transceiver module. Inserting the SFP+ transceiver module Figure 90: Inserting the SFP+ transceiver module Ê Insert and slide the SFP+ transceiver module into the socket connector as far as it will go.
  • Page 171 Expansion cards and backup units Figure 91: Latching the locking bail Ê Carefully fold up and latch the locking bail. Figure 92: Attaching the protective optical port plug Ê If the SFP+ transceiver module is not immediately connected to an LC connector, attach the protective optical port plug to the transceiver optical bores.

  • Page 172: Removing An Sfp+ Transceiver Module

    Expansion cards and backup units Installing the secondary SFP+ transceiver module Figure 93: Installing the secondary SFP+ transceiver module Ê If applicable, install the secondary SFP+ transceiver module accordingly. 9.3.2 Removing an SFP+ transceiver module Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less For Fiber Channel over Ethernet (FCoE) configurations, the ethernet server...
  • Page 173 Expansion cards and backup units Figure 94: Removing the protective optical port plug Ê If present, remove the protective optical port plug from the SFP+ transceiver module. CAUTION! Save the protective port plug for future use. Figure 95: Unlatching the locking bail Ê...
  • Page 174 Expansion cards and backup units Figure 96: Removing the SFP+ transceiver Ê Pull the SFP+ transceiver module out of its socket connector. Ê Reattach the protective optical port plug to the transceiver optical bores. Place the removed SFP+ transceiver module in an antistatic bag or other protective environment.

  • Page 175: Expansion Cards And Riser Card

    Expansion cards and backup units Expansion cards and riser card 9.4.1 Installing expansion cards Upgrade and Repair Unit Hardware: 5 minutes (URU) Software: 5 minutes Tools: Phillips PH2 / (+) No. 2 screw driver 9.4.1.1 Preliminary steps "Disabling BitLocker functionality" on page 69 Ê...

  • Page 176: Removing The Pci Slot Bracket

    Expansion cards and backup units 9.4.1.2 Removing the PCI slot bracket Figure 97: Removing the PCI slot bracket Ê Fold up the locking handle on the slot bracket clamp (1). Ê Press down on the slot bracket clamp to disengage it (2). Ê...

  • Page 177: Installing An Expansion Card

    Expansion cards and backup units 9.4.1.3 Installing an expansion card Ê Remove the expansion card from its protective packaging. For further instructions regarding controller settings, please refer to the accompanying documentation. Ê If applicable, attach the required slot bracket to the expansion card as described in section "Installing a slot bracket"...

  • Page 178: Concluding Steps

    Expansion cards and backup units Figure 99: Installing the expansion card (B) Ê Clip on the PCI slot bracket clamp (1). Ê Fold down the locking handle on the PCI slot bracket clamp until it locks in place (2). Ê If applicable, connect internal cables to the expansion card (see section "Cabling plans"...

  • Page 179: Removing Expansion Cards

    Expansion cards and backup units "Connecting the server to the mains" on page 67 Ê "Switching on the server" on page 68 Ê "Updating RAID controller firmware" on page 80 Ê Ê If applicable, "Enabling Option ROM scan" on page 81 "Enabling SVOM boot watchdog functionality"...

  • Page 180: Removing An Expansion Card

    Expansion cards and backup units 9.4.2.2 Removing an expansion card Ê If applicable, disconnect internal cables from the expansion card. Ê If applicable, remove SFP+ transceiver modules "Removing an SFP+ transceiver module" on page 172. Figure 100: Removing an expansion card Ê...

  • Page 181: Installing A Pci Slot Bracket

    Expansion cards and backup units 9.4.2.3 Installing a PCI slot bracket CAUTION! Always replace slot brackets into unused PCI slot openings to comply with applicable EMC regulations and satisfy cooling requirements. Figure 101: Installing a PCI slot bracket Ê Insert a PCI slot bracket into the unused PCI slot opening (1). Ê...

  • Page 182: Replacing Expansion Cards

    Expansion cards and backup units 9.4.3 Replacing expansion cards Upgrade and Repair Unit Hardware: 5 minutes (URU) Software: 5 minutes Tools: Phillips PH2 / (+) No. 2 screw driver (only for installing slot brackets) Note on network settings recovery When replacing network controllers or the system board, network configuration settings in the operating system will be lost and replaced by default values.

  • Page 183: Removing The Defective Expansion Card

    Expansion cards and backup units 9.4.3.2 Removing the defective expansion card Ê If applicable, remove SFP+ transceiver modules from the expansion card to be removed, as described in section "Removing an SFP+ transceiver module" on page 172. Ê Remove the expansion card as described in section "Removing expansion cards"...

  • Page 184: Replacing The Riser Card

    Expansion cards and backup units Ê If applicable, reconfigure your network settings in the operation system according to the original configuration of the replaced controller (expansion card or onboard). Configuration of network settings should be performed by the customer. For further information, please refer to section "Note on network settings recovery"...

  • Page 185: Installing The New Riser Card

    Expansion cards and backup units Figure 102: Removing the riser card Ê Disconnect the power cable (1). Ê Remove the two screws (2). Ê Remove the riser card (3). Ê Remove the PCI adapter board from slot 1 (4). 9.4.4.3 Installing the new riser card Figure 103: Preparing the riser card Ê...

  • Page 186: Concluding Steps

    Expansion cards and backup units Ê Angle the PCI adapter board (2). Figure 104: Installing the riser card Ê Insert the PCI adapter board in slot 1 (1). Ê Fit the riser card onto the two spacer bolts (2). Ê Fasten the riser card with the two screws (3). Ê...

  • Page 187: Replacing The Tfm

    Expansion cards and backup units 9.4.5 Replacing the TFM Upgrade and Repair Unit Hardware: 10 minutes (URU) Tools: Phillips PH1 / (+) No. 1 screw driver 9.4.5.1 Preliminary steps "Locating the defective server" on page 43 Ê "Disabling BitLocker functionality" on page 69 Ê...

  • Page 188: Installing The New Tfm

    Expansion cards and backup units Figure 105: Removing the TFM Ê Remove the three screws (1). Ê Remove the TFM (2). 9.4.5.3 Installing the new TFM Ê Install the new TFM as described in section "Installing the FBU in the holder" on page 191.

  • Page 189: Backup Units

    Expansion cards and backup units Backup Units 9.5.1 Basic information The Battery Backup Unit (BBU) or Flash Backup Unit (FBU) backs up the memory contents of the connected SAS RAID controller in the event of a power failure. The server can accommodate up to two backup units. 9.5.2 Installing an FBU Upgrade and Repair Unit...

  • Page 190: Installing Tfm To The Raid Controller (If Applicable)

    Expansion cards and backup units 9.5.2.2 Installing TFM to the RAID controller (if applicable) Figure 106: TFM kit Screws Figure 107: Installing TFM Ê Fit the spacer bolts of the TFM on the RAID controller (1). Ê Secure the TFM on the RAID controller with the three screws (2). Upgrade and Maintenance Manual TX1330 M1...

  • Page 191: Installing The Fbu In The Holder

    Expansion cards and backup units 9.5.2.3 Installing the FBU in the holder Figure 108: Installing the FBU in the holder (A) Ê At a slight angle, fit the FBU under the right retaining bracket on the holder. Ê Push down the FBU until it locks in place. Upgrade and Maintenance Manual TX1330 M1...
  • Page 192 Expansion cards and backup units Figure 109: Installing the FBU in the holder (B) Ê Ensure that the FBU is properly seated in the holder. Upgrade and Maintenance Manual TX1330 M1...
  • Page 193 Expansion cards and backup units Figure 110: Connecting the FBU adapter cable to the FBU Ê Connect the cable end on the FBU to the FBU adapter cable. Upgrade and Maintenance Manual TX1330 M1...

  • Page 194: Installing The Fbu Holder Into The Chassis

    Expansion cards and backup units 9.5.2.4 Installing the FBU holder into the chassis FBU 1 FBU 2 Figure 111: Installing the FBU holder (A) Note the positions of the fixation bolts on the chassis floor and keyhole slots on the FBU holder. Ê...
  • Page 195 Expansion cards and backup units Figure 112: Installing the FBU holder (B) Ê Slide the FBU holder downward as far as it will go. The fixation bolts on the chassis floor will lock in the narrow ends of the keyhole slots on the holder. Ê...

  • Page 196: Connecting The Fbu Adapter Cable To The Tfm

    Expansion cards and backup units 9.5.2.5 Connecting the FBU adapter cable to the TFM Figure 113: Routing the FBU adapter cable Ê Connect the FBU adapter cable to the TFM. Ê Route the FBU adapter cable as shown. 9.5.2.6 Concluding steps "Installing the fan module"...

  • Page 197: Installing A Bbu

    Expansion cards and backup units 9.5.3 Installing a BBU Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less CAUTION! For further safety information, please refer to chapter "Important information" on page 9.5.3.1 Preliminary steps "Disabling SVOM boot watchdog functionality" on page 70 Ê...

  • Page 198: Installing The Bbu In The Holder

    Expansion cards and backup units CAUTION! Make sure that the connector side with the three dots is on the top (see close-up). Otherwise you risk short-circuits. 9.5.3.3 Installing the BBU in the holder Figure 115: Installing the BBU in the BBU holder Ê...

  • Page 199: Concluding Steps

    Ê If the BBU status does not change after 8 hours, please try to initiate the recalibration process manually using the ServerView RAID Manager. If this procedure still does not fix the BBU status, please contact your local Fujitsu customer service partner. Upgrade and Maintenance Manual TX1330 M1...

  • Page 200: Removing An Fbu

    Expansion cards and backup units 9.5.4 Removing an FBU Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less CAUTION! Do not throw FBUs into the trash can. Batteries must be disposed of in accordance with local regulations concerning special waste. For further safety information, please refer to section "Environmental protection"...

  • Page 201: Removing The Fbu Holder From The Chassis

    Expansion cards and backup units 9.5.4.3 Removing the FBU holder from the chassis Figure 117: Removing the FBU holder from the chassis Ê Lift up the green locking handle on the FBU holder (1) while sliding the BBU holder upward as far as it will go (2). After that, the fixation bolts on the chassis floor will rest in the wide ends of the keyhole slots on the holder.

  • Page 202: Removing A Bbu

    Expansion cards and backup units 9.5.5 Removing a BBU Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less CAUTION! Do not throw battery backup units into the trash can. Batteries must be disposed of in accordance with local regulations concerning special waste.

  • Page 203: Replacing An Fbu

    Expansion cards and backup units 9.5.6 Replacing an FBU Upgrade and Repair Unit Hardware: 10 minutes (URU) Tools: tool-less CAUTION! Do not throw FBUs into the trash can. Batteries must be disposed of in accordance with local regulations concerning special waste. For further safety information, please refer to section "Environmental protection"...
  • Page 204 Expansion cards and backup units Figure 118: Disconnecting the FBU adapter cable from the FBU Ê Press down on the locking latch on the FBU cable (see close-up) and disconnect the FBU adapter cable. Upgrade and Maintenance Manual TX1330 M1...

  • Page 205: Installing The New Fbu

    Expansion cards and backup units Figure 119: Removing the FBU from the holder Ê At a slight angle, slide the FBU from under the retaining brackets of the holder and remove it. 9.5.6.3 Installing the new FBU Ê Install the FBU as described in section "Installing an FBU"...

  • Page 206: Replacing A Bbu

    Expansion cards and backup units 9.5.7 Replacing a BBU Upgrade and Repair Unit Hardware: 10 minutes (URU) Tools: tool-less CAUTION! Do not throw battery backup units into the trash can. Batteries must be disposed of in accordance with local regulations concerning special waste.
  • Page 207 Expansion cards and backup units Figure 120: Removing the BBU from the BBU holder Ê Press out on the right retaining bracket on the BBU holder to disengage the locking mechanism while pulling up on the BBU (1). Ê Fold up the BBU and at a slight angle remove it from the BBU holder (2). Figure 121: Disconnecting the BBU cable from the BBU Ê...

  • Page 208: Installing The New Bbu

    Ê If the BBU status does not change after 8 hours, please try to initiate the recalibration process manually using the ServerView RAID Manager. If this procedure still does not fix the BBU status, please contact your local Fujitsu customer service partner. Upgrade and Maintenance Manual TX1330 M1...

  • Page 209: Main Memory

    Main memory Safety notes CAUTION! Do not install unsupported third party memory modules. For further ● information on supported memory modules, refer to section "Basic information" on page 209. Memory modules remain hot after shutdown. Wait for components to ● cool down before installing or removing memory modules to prevent burns.

  • Page 210: Memory Sequence

    Main memory 10.1.1 Memory sequence – Populate memory slot 1 / channel A (DIMM-1A) first. – Within both channels, memory slot 1 must be populated prior to slot 2. – If memory modules with different capacities are used: – Install modules with higher capacities first. –...

  • Page 211: Operation Modes

    Main memory 10.1.2 Operation modes – The maximum performance can be achieved in a symmetric dual-channel configuration. Therefore both channels have to be populated with the same amount of memory. The DRAM device technology (1 Gbit / 2 Gbit / 4 Gbit) may vary from one channel to the other.

  • Page 212: Removing A Memory Module

    Main memory 10.2.2 Removing a memory module Ê Identify the desired memory slot see section "Memory sequence" on page 210. CAUTION! Ensure to maintain an operational configuration when removing memory modules. For additional information, please refer to section "Basic information" on page 209.

  • Page 213: Installing Memory Modules

    Main memory 10.3 Installing memory modules Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 10.3.1 Preliminary steps "Disabling BitLocker functionality" on page 69 Ê "Disabling SVOM boot watchdog functionality" on page 70 Ê "Shutting down the server" on page 46 Ê...

  • Page 214: Concluding Steps

    Main memory Ê Align the notch on the bottom of the module with the crossbar in the slot (see close-up). Ê Press down on the memory module until the securing clips snap into the cutouts at each end of the module (2). 10.3.3 Concluding steps "Installing the fan module"...

  • Page 215: Removing The Defective Memory Module

    Main memory "Disconnecting the server from the mains" on page 46 Ê "Getting access to the component" on page 47 Ê "Removing the fan module" on page 151 Ê Ê Locate the defective memory module using the onboard Local Diagnostic LEDs (see section "Onboard indicators and controls"...
  • Page 216 Main memory Upgrade and Maintenance Manual TX1330 M1...

  • Page 217: Processors

    Processors Safety notes CAUTION! Do not install unsupported processors. For further information on ● supported processors, refer to section "Basic information" on page 218. Circuit boards and soldered parts of internal options are exposed and ● can be damaged by static electricity. Always discharge static build-up (e.g.

  • Page 218: Basic Information

    Processors 11.1 Basic information Supported processors The system board is equipped with one LGA 1150 socket for dual and quad Core Intel Xeon E3-1200v3 processor series CPUs. 11.2 Upgrading or replacing the processor Field Replaceable Unit Hardware: 15 minutes (FRU) Software: 5 minutes Tools: Phillips PH2 / (+) No.

  • Page 219: Removing The Processor Heat Sink

    Processors 11.2.2 Removing the processor heat sink Figure 125: Removing the processor heat sink Ê Loosen the four captive screws on the heat sink in a crossover pattern (1-4). Ê Carefully turn the heat sink back and forth to detach it from the processor. This may be necessary due to the adhesive quality of the thermal paste located between the heat sink and processor.

  • Page 220: Removing The Processor

    Processors 11.2.3 Removing the processor Figure 126: Unlatching the socket lever Ê Unlatch the socket lever by pushing it down and away from the socket (1). Ê Fold back the socket release lever (2). Figure 127: Removing the processor Ê Rotate the socket lever to lift the load plate away from the socket (1). Upgrade and Maintenance Manual TX1330 M1...

  • Page 221: Installing The Processor

    Processors Ê Make sure that the load plate is in the fully open position. Ê Carefully remove the defective processor from its socket in a vertical motion (2). CAUTION! Be careful not to touch or bend the spring contacts on the processor socket.
  • Page 222 Processors Figure 129: Closing the load plate (A) Ê Lower the load plate over the processor while leaving the socket lever in the open position. Figure 130: Closing the load plate (B) Ê Lower the socket lever while making sure that the front edge of the load plate slides under the shoulder screw cap (see close-up) as the lever is lowered.

  • Page 223: Applying Thermal Paste

    Processors Figure 131: Latching the socket lever Ê Latch the socket lever under the load plate tab. 11.2.5 Applying thermal paste For the Japanese market, the service engineer must follow the instruction provided separately. If the processor upgrade or replacement kit contains a new CPU heat sink, a thin layer of thermal compound has already been pre-applied to its lower surface.
  • Page 224 Processors Figure 132: Thermal paste syringe One thermal compound syringe (FTS-FSP:P304000004) contains thermal paste for three processors. In order to determine the correct amount of thermal paste (equal to 1.0 gram), divide the grey area of the syringe up into three equal segments. Add graduation marks to the syringe using a permanent marker to help you apply the thermal paste.

  • Page 225: Installing The Processor Heat Sink

    Processors Figure 133: Applying thermal paste Ê Apply a small point-shaped amount of thermal paste (1.0 gram, see description above) to the center of the processor surface as shown. CAUTION! Do not mix different types of thermal paste. 11.2.6 Installing the processor heat sink Figure 134: Installing the heat sink (A) Ê...
  • Page 226 Processors CAUTION! – Ensure that the screws on the heat sink are properly seated on the threaded holes. – Ensure that the heat sink cooling fins match the direction of the airflow! Figure 135: Installing the heat sink (B) Ê Fasten the four captive screws on the heat sink in a crossover pattern (screw torque: 0.6 Nm, not applicable for the Japanese market) (1-4).

  • Page 227: Concluding Steps

    Processors 11.2.7 Concluding steps "Installing the fan module" on page 152 Ê "Reassembling" on page 58 Ê "Connecting the server to the mains" on page 67 Ê "Switching on the server" on page 68 Ê Ê If applicable, "Updating or recovering the system board BIOS and iRMC" on page 76 "Enabling SVOM boot watchdog functionality"...

  • Page 228: Concluding Steps

    Processors Ê Install the processor heat sink as described in section "Installing the processor heat sink" on page 225. 11.3.3 Concluding steps "Installing the fan module" on page 152 Ê "Reassembling" on page 58 Ê "Connecting the server to the mains" on page 67 Ê...

  • Page 229: Accessible Drives

    Accessible drives Safety notes CAUTION! Before installing an accessible drive, acquaint yourself with the ● drive's user documentation. When inserting an accessible drive into the server, ensure not to ● pinch or strain any connected cables. When installing an accessible drive, hold it by its sides. Applying force ●...

  • Page 230: Basic Information

    Accessible drives 12.1 Basic information Mounting order for accessible drives The server offers three 5.25-inch accessible drive bays for optical disk drives and backup drives: 5.25 inch x 1.6 inch Figure 136: Accessible drives mounting order (tower server) 5.25 inch x 1.6 inch Figure 137: Accessible drives mounting order (rack server) Upgrade and Maintenance Manual TX1330 M1...

  • Page 231: Installing Accessible Drives

    Accessible drives Sequence Accessible drive Max. no. Optical disk drive or Bay 1 slimline optical disk drive Bay 3, if occupied: bay 2 Backup drive LTOx or bay 1 Bay 3, if occupied: bay 2 Backup drive DAT or bay 1 Bay 3, if occupied: bay 2 Backup drive RDX or bay 1...

  • Page 232: Removing Accessible Drive Dummy Covers

    Accessible drives 12.2.2 Removing accessible drive dummy covers Removing accessible drive filler covers Figure 138: Removing an accessible drive filler cover Ê Hold the accessible drive filler cover by its two handle recesses and pull it out of the desired installation bays. CAUTION! Always replace filler covers into unused drive bays to comply with applicable EMC regulations and satisfy cooling requirements.
  • Page 233 Accessible drives Removing accessible drive covers Figure 139: Removing an accessible drive covers Removing accessible drive covers is illustrated by the example of the tower server. In case of the rack front cover, the procedure is identical. Ê Turn the front cover face down. Ê...

  • Page 234: Installing Mounting Brackets To Rdx And Dat Backup Drives (If Applicable)

    Accessible drives 12.2.3 Installing mounting brackets to RDX and DAT backup drives (if applicable) This section is not applied for Japanese market. Backup drive mounting brackets are contained in mounting kit S26361-F3753- E1 (to be ordered separately with the backup drive). No new mounting brackets are available when replacing a backup drive during service.
  • Page 235 Accessible drives Figure 142: Securing mounting brackets to an RDX backup drive Ê Secure the backup drive mounting brackets to the RDX backup drive with two screws per bracket as shown. Figure 143: Securing mounting brackets to a DAT72 backup drive Ê...

  • Page 236: Installing The Slimline Optical Disk Drive In The Slide-In Unit (If Applicable)

    Accessible drives 12.2.4 Installing the slimline optical disk drive in the slide- in unit (if applicable) Figure 144: Slide-in unit for slimline ODD Figure 145: Mounting the slimline ODD in the slide-in unit Ê Insert the slimline ODD on the top. Ê...

  • Page 237: Installing An Accessible Drive

    Accessible drives 12.2.5 Installing an accessible drive Figure 146: Opening the accessible drive locking bar Ê Press out on the locking latch to disengage the accessible drive locking bar (1). Ê Fold up the accessible drive locking bar (2). Unlocking and securing the front panel and accessible drives is illustrated by the example of tower servers.
  • Page 238 Accessible drives Figure 148: Inserting the accessible drive Ê Insert the accessible drive into its installation bay and carefully push in until the front screw hole on the front panel frame lines up with the centering pin on the locking bar (1). CAUTION! For installing a LTO drive: ensure that the power cables routed behind the accessible drive cage are not trapped when pushing the LTO...

  • Page 239: Cabling Of Rdx Drive

    Accessible drives 12.2.5.1 Cabling of RDX drive Figure 149: Cabling of RDX backup drive Ê Connect the connector on the RDX drive to the USB 3.0 cable of the front panel (1). Ê Connect the connector P1 to system board connector SATA POWER (2). Ê...

  • Page 240: Concluding Steps

    Accessible drives Figure 150: Front panel with USB 3.0 cable for connecting RDX backup drives Ê Use the connector marked with the circle for the connection of the RDX backup drive. Notes on RDX backup drive USB cabling: – A USB 2.0 RDX drive may be replaced by a USB 3.0 RDX drive with previous cabling.

  • Page 241: Removing Accessible Drives

    Accessible drives 12.3 Removing accessible drives Upgrade and Repair Unit Hardware: 10 minutes (URU) Tools: Phillips PH2 / (+) No. 2 screw driver (for removing the rack front cover) Other procedures: tool-less 12.3.1 Preliminary steps "Disabling BitLocker functionality" on page 69 Ê...
  • Page 242 Accessible drives Figure 151: Removing the accessible drive Ê Carefully pull the accessible drive out of its installation bay (1). Ê Close the locking bar (2) until it locks in place (3). Upgrade and Maintenance Manual TX1330 M1...

  • Page 243: Installing Accessible Drive Dummy Covers

    Accessible drives 12.3.3 Installing accessible drive dummy covers Installing accessible drive filler covers Figure 152: Installing an accessible drive filler cover Ê Hold the accessible drive filler cover by its two handle recesses and insert it into the empty installation bays with the punched-out arrow symbol facing CAUTION! Always replace filler covers into unused drive bays to comply with applicable EMC regulations and satisfy cooling requirements.

  • Page 244: Concluding Steps

    Accessible drives Installing accessible drive covers Figure 153: Installing accessible drive covers Installing accessible drive covers is illustrated by the example of the tower server. In case of the rack front cover, the procedure is identical. Ê Ensure that an accessible drive filler cover has been installed in every empty drive bay.

  • Page 245: Replacing Accessible Drives

    Accessible drives Ê If applicable, "Verifying and configuring the backup software solution" on page 81 "Enabling BitLocker functionality" on page 90 Ê 12.4 Replacing accessible drives Upgrade and Repair Unit Hardware: 15 minutes (URU) Tools: Phillips PH2 / (+) No. 2 screw driver (for installing mounting brackets) 12.4.1 Preliminary steps "Disabling BitLocker functionality"...

  • Page 246: Installing The New Accessible Drive

    Accessible drives Ê If applicable, remove the defective slimline ODD from the slide-in unit. 12.4.3 Installing the new accessible drive Ê Install the accessible drive as described in section "Installing an accessible drive" on page 237. 12.4.4 Concluding steps "Installing the rack front cover" on page 58 (rack server) or "Installing the Ê...

  • Page 247: Front Panel Module

    Front panel module Safety notes CAUTION! When inserting the front panel module into the server, ensure not to ● pinch or strain any connected cables. Circuit boards and soldered parts of internal options are exposed and ● can be damaged by static electricity. Always discharge static build-up (e.g.

  • Page 248: Replacing The Front Panel Module

    Front panel module 13.1 Replacing the front panel module Field Replaceable Unit Hardware: 10 minutes (FRU) Software: 5 minutes Tools: Phillips PH2 / (+) No. 2 screw driver (for removing the rack front cover) Other procedures: tool-less Note on system information backup / restore The front panel module contains the Chassis ID EPROM that contains system information like server name and model, housing type, serial number and manufacturing data.

  • Page 249: Removing The Defective Front Panel Module

    Front panel module "Removing the fan module" on page 151 Ê 13.1.2 Removing the defective front panel module Figure 154: Disconnecting cables from system board Ê Disconnect the front panel cable (1) and the front USB cable (2) from the system board.
  • Page 250 Front panel module Figure 155: Removing the front panel module Ê Press out on the locking latch to disengage the accessible drive locking bar (1). Ê Fold up the accessible drive locking bar (2). Ê Carefully pull the front panel module out of its bay (3). CAUTION! Ensure that none of the cables are strained or damaged! Figure 156: Removing the cable clamp...

  • Page 251: Installing The New Front Panel Module

    Front panel module Ê If applicable, cut open the cable clamp (see circle) and remove it. Figure 157: Removing the front panel cable Ê Remove the front panel cable from the front panel module. 13.1.3 Installing the new front panel module Ê...

  • Page 252: Concluding Steps

    Front panel module Ê Close the locking bar (2) until it locks in place (3). Ê Connect the front panel cable and the front USB cable to the system board (see figure 154). Ê Store both cables in the cable clamp (see figure 154). 13.1.4 Concluding steps "Installing the fan module"...

  • Page 253: System Board And Components

    System board and components Safety notes CAUTION! Devices and components inside the server remain hot after ● shutdown. After shutting down the server, wait for hot components to cool down before installing or removing internal options. Circuit boards and soldered parts of internal options are exposed and ●...

  • Page 254: Replacing The Cmos Battery

    System board and components 14.2 Replacing the CMOS battery Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less; recommended: tooth pick Safety notes CAUTION! The CMOS battery must be replaced with an identical battery or with ● a battery type recommended by the manufacturer. Keep lithium batteries away from children.

  • Page 255: Replacing The Defective Cmos Battery

    System board and components 14.2.2 Replacing the defective CMOS battery Figure 159: Removing the CMOS battery Ê Press out on the locking spring to eject the depleted CMOS battery (1). Ê If the CMOS battery cannot be ejected this way, use a toothpick (recommended) or similar tool as a lever: Insert the toothpick between the battery and locking spring as shown (2).

  • Page 256: Concluding Steps

    System board and components Figure 160: Installing the CMOS battery Ê At a slight angle, fit the new CMOS battery into its socket as shown (1). CAUTION! Ensure to insert the CMOS battery with the positive pole (label side) facing up as shown (see close-up). Ê...

  • Page 257: Usb Flash Module (Ufm)

    System board and components 14.3 USB Flash Module (UFM) 14.3.1 Installing the UFM Field Replaceable Unit Hardware: 5 minutes (FRU) Software: 5 minutes Tools: tool-less 14.3.1.1 Preliminary steps "Disabling BitLocker functionality" on page 69 Ê "Disabling SVOM boot watchdog functionality" on page 70 Ê...

  • Page 258: Concluding Steps

    System board and components Figure 162: UFM mounting location Figure 163: Installing the UFM Ê Connect the UFM to the system board, snapping in the UFM spacer. 14.3.1.3 Concluding steps "Reassembling" on page 58 Ê "Connecting the server to the mains" on page 67 Ê...

  • Page 259: Software Configuration

    System board and components 14.3.1.4 Software configuration The UFM delivery set includes the "Recovery Tool CD" to setup the ESXi configuration. Proceed as follows: Ê Switch on the server. Ê Right after switching on the server, insert the "Recovery Tool CD" into the DVD drive and close the drive tray.

  • Page 260: Removing The Ufm

    System board and components 14.3.2.2 Removing the UFM Figure 164: Removing the UFM (A) Ê Remove the nylon screw (1). Ê Disconnect and remove the UFM (2). Figure 165: Removing the UFM (B) Ê The UFM spacer remains on the system board. 14.3.2.3 Concluding steps "Reassembling"...

  • Page 261: Replacing The Ufm

    System board and components 14.3.3 Replacing the UFM Field Replaceable Unit Hardware: 10 minutes (FRU) Software: 5 minutes Tools: – Phillips PH1 / (+) No. 1 screw driver – combination pliers and flat nose pliers 14.3.3.1 Preliminary steps "Disabling BitLocker functionality" on page 69 Ê...

  • Page 262: Installing The New Ufm

    System board and components 14.3.3.3 Installing the new UFM Figure 166: Preparing the new UFM Ê Remove the nylon screw from the new UFM (1). Ê Remove the UFM spacer (2). Figure 167: Installing the UFM Ê Fit the UFM on the UFM connector and the remaining UFM spacer (1). Ê...

  • Page 263: Concluding Steps

    System board and components Destroying the defective UFM CAUTION! The UFM contains customer information (e.g. IP address, license numbers). After replacing the UFM, hand the defective UFM over to the customer. If the customer requests disposal of the defective UFM, proceed as follows: Figure 168: Destroying the defective UFM Ê...

  • Page 264: Software Configuration

    System board and components 14.3.3.5 Software configuration The UFM delivery set includes the "Recovery Tool CD" to setup the ESXi configuration. Proceed as follows: Ê Switch on the server. Ê Right after switching on the server, insert the "Recovery Tool CD" into the DVD drive and close the drive tray.

  • Page 265: Installing The Tpm

    System board and components 14.4.1.2 Installing the TPM Figure 169: TPM kit TPM (Trusted Platform Module) Special screw for TPM TPM spacer TPM bit insert for TPM special screw The black TPM spacer is not used in this server. Figure 170: TPM mounting location Figure 171: Installing the TPM spacer Ê...
  • Page 266 System board and components Figure 172: Installing the TPM Ê Connect the TPM to the system board. Figure 173: TPM bit insert Ê Attach the TPM bit insert or TPM module fixing tool (Japanese market) to a bit screw driver. Upgrade and Maintenance Manual TX1330 M1...

  • Page 267: Concluding Steps

    System board and components Figure 174: Securing the TPM Ê Secure the TPM with the TPM screw using the TPM bit insert. Do not fasten the screw too firmly. Stop as soon as the head of the screw lightly touches the TPM. 14.4.1.3 Concluding steps "Reassembling"...

  • Page 268: Removing The Tpm

    System board and components 14.4.2 Removing the TPM Field Replaceable Unit Hardware: 30 minutes (FRU) Tools: Removing the system board: – Phillips PH2 / (+) No. 2 screw driver Installing the TPM: – Bit screw driver – TPM bit insert –...

  • Page 269: Removing The Tpm

    For further information on how to disable BitLocker drive encryption, please refer to the Microsoft Knowledge Base. Fujitsu service partners will find additional information (also available in Japanese) on the Fujitsu Extranet web pages. Ê Disable TPM in the system board BIOS. Proceed as follows: Ê...
  • Page 270 System board and components Figure 175: Removing the TPM screw Ê Locate the slotted lower end of the TPM screw (1). Ê Carefully loosen the TPM screw using a thin slotted screw driver (e.g. watchmaker's screw driver) or the dedicated TPM screw driver (Japanese market) (2).

  • Page 271: Concluding Steps

    System board and components Figure 176: Removing the TPM spacer Ê Using a small pair of combination pliers, press together the hooks on the TPM spacer (1, see close-up) and remove it from the system board (2). If the TPM is to be replaced, the TPM spacer may remain on the system board.

  • Page 272: Replacing The Tpm

    System board and components 14.4.3 Replacing the TPM Field Replaceable Unit Hardware: 40 minutes (FRU) Tools: Removing the system board: – Phillips PH2 / (+) No. 2 screw driver Replacing the TPM: – Bit screw driver – TPM bit insert –...

  • Page 273: Removing The Defective Tpm

    System board and components 14.4.3.2 Removing the defective TPM Ê Remove the TPM as described in section "Removing the TPM" on page 268. Ê Leave the TPM spacer on the system board when removing the defective TPM. 14.4.3.3 Installing the new TPM Ê...

  • Page 274: Replacing The System Board

    System board and components 14.5 Replacing the system board Field Replaceable Unit Hardware: 50 minutes (FRU) Software: 10 minutes Tools: Replacing the system board: – Phillips PH2 / (+) No. 2 screw driver – Magnifying glass for inspecting processor socket springs (recommended) Replacing the TPM: –...
  • Page 275 System board and components – If the customer is using TPM functionality, remove the TPM from the old system board and install it on the new system board. Advise your contact persons that they must provide you with TPM backup copies. For security reasons, the TPM must be restored / re- saved by the customer.

  • Page 276: Preliminary Steps

    System board and components 14.5.1 Preliminary steps "Disabling BitLocker functionality" on page 69 Ê "Disabling SVOM boot watchdog functionality" on page 70 Ê "Locating the defective server" on page 43 Ê "Shutting down the server" on page 46 Ê "Disconnecting the server from the mains" on page 46 Ê...
  • Page 277 System board and components Figure 177: Screws system board Ê Remove eight screws from the system board (see circles). Figure 178: Detaching the system board Ê Slightly lift up the system board by the memory module ejectors and a PCI slot (1) in order to detach it from the centering bolts (C).
  • Page 278 System board and components Ê Carefully shift the system board towards the server front until the plug shells disengage from the cut-outs in the connector panel (2). Figure 179: Removing the system board Ê Hold the defective system board by the memory module ejectors and a PCI slot and at a slight angle lift it out of the chassis.

  • Page 279: Installing The New System Board

    System board and components Ê Using a small pair of combination pliers, press together the hooks on the power cable clamp (1) and remove it from the defective system board (2). 14.5.3 Installing the new system board Figure 181: Installing the system board (A) Ê...
  • Page 280 System board and components Figure 182: Installing the system board (B) Ê Carefully shift the system board towards the server rear until the plug shells engage with the cut-outs in the connector panel. Ê Lower the system board onto the centering bolts (C). Ensure that the system board is properly seated on both centering bolts.

  • Page 281: Swapping The Processor

    System board and components Ê Verify the settings on the new system board (see section "Onboard settings" on page 333). 14.5.4 Swapping the processor Figure 184: Unlatching the socket lever (new system board) Ê Unlatch the socket lever on the new system board by pushing it down and away from the socket (1).
  • Page 282 System board and components Figure 185: Removing the protective socket cover (new system board) Ê Place your thumb against the front edge of the protective socket cover and rest your index finger on the rear grip. CAUTION! Be careful not to touch or bend the pins on the processor socket! Save the socket cover for future use.
  • Page 283 System board and components Ê Carefully remove the processor from its socket on the defective system board as described in section "Removing the processor" on page 220. Ê Install the processor on the new system board as described in section "Installing the processor"...
  • Page 284 System board and components Figure 187: Installing the protective socket cover (defective system board) (B) Ê Lower the load plate over the processor while leaving the socket lever in the open position. Ê Lower the socket lever while making sure that the front edge of the load plate slides under the shoulder screw cap (see close-up) as the lever is lowered.

  • Page 285: Concluding Steps

    System board and components 14.5.5 Concluding steps Ê Reconnect all cables to the system board. For a complete cabling overview, please refer to section "Cabling plans" on page 303. Ê Reinstall all remaining system board components as shown in the related sections: –...
  • Page 286 System board and components "Verifying the system time settings" on page 86 Ê "Looking up changed MAC / WWN addresses" on page 91 Ê "Updating the NIC configuration file in a Linux environment" on page 88 Ê "Enabling SVOM boot watchdog functionality" on page 84 Ê...

  • Page 287: Converting A Tower Model To A Rack Model

    Converting a tower model to a rack model Field Replaceable Unit Hardware: 20 minutes (FRU) Tools: – Phillips PH2 / (+) No. 2 screw driver – Slotted screw driver Safety notes CAUTION! For further information, please refer to chapter "Important ●...

  • Page 288: Converting A Tower Model To A Rack Model

    Converting a tower model to a rack model 15.2 Converting a tower model to a rack model Removing the right side cover Figure 189: Removing the right side cover (A) Ê Remove two screws on the server rear (see circles). Upgrade and Maintenance Manual TX1330 M1...
  • Page 289 Converting a tower model to a rack model Figure 190: Removing the right side cover (B) Ê Slide the right side cover towards the server rear as far as it will go (1). Ê Remove the three hooks on the right side cover from the slots on the upper chassis edge: Ê...
  • Page 290 Converting a tower model to a rack model Removing rubber feet Figure 191: Removing rubber feet Ê Using a slotted screw driver, slightly pry up on each rubber foot until it detaches. Ê Bring the server back to its horizontal position. At least two people are needed to turn over a fully equipped server.
  • Page 291 Converting a tower model to a rack model Removing the accessible drive cage Ê Remove the front panel module as described in section "Removing the defective front panel module" on page 249. Ê If applicable, remove all accessible drives as described in section "Removing an accessible drive"...
  • Page 292 Converting a tower model to a rack model Figure 193: Detaching the accessible drive cage (B) Ê Remove two screws from the right chassis edge (1). Ê Remove two screws from the top edge of the chassis (2). Upgrade and Maintenance Manual TX1330 M1...
  • Page 293 Converting a tower model to a rack model Figure 194: Removing the accessible drive cage Ê Slightly lift up the accessible drive cage to disengage its front bottom edge from the slot on the chassis floor (1). Ê Slide the accessible drive cover from under the chassis frame as shown (2). Ê...
  • Page 294 Converting a tower model to a rack model Converting the accessible drive cage Figure 195: Converting the accessible drive cage Ê Turn the accessible drive cover with its "RACK" stamping facing up (1, see close-up). Ê Remove the threaded bolt from the upper edge of the accessible drive cage (2).
  • Page 295 Converting a tower model to a rack model Reinstalling the accessible drive cage Figure 196: Mounting the accessible drive cage Ê With its "RACK" stamping facing up, lower the accessible drive cage into the chassis (1). Ê Slide the accessible drive cage towards the server front as far as it will go (2).
  • Page 296 Converting a tower model to a rack model Figure 197: Securing the accessible drive cage (A) Ê Secure the accessible drive cage with two screws (1). Ê Secure the accessible drive cage with two screws (2). Ê Ensure that all cables and components are properly secured inside the server and that there are no loose pieces.
  • Page 297 Converting a tower model to a rack model Figure 198: Securing the accessible drive cage (B) Ê Carefully turn the server upside down. At least two people are needed to turn over a fully equipped server. Remove hard disk drives and power supply modules in order to facilitate the task.
  • Page 298 Converting a tower model to a rack model Ê Attach a rubber bumper to the front intrusion switch and reinstall the intrusion switch module as described in section "Installing the new intrusion switch cable" on page 314. Assembling the rack front cover Figure 199: Rack mounting brackets with quick release levers The rack front cover consists of a plastic frame and two rack mounting brackets with quick release levers.
  • Page 299 Converting a tower model to a rack model Ê Firmly press down on the rack mounting bracket until it is fully seated in the rack front bezel (2). Ê Mount the second rack mounting bracket accordingly. Figure 201: Installing accessible drive dummy covers Ê...

  • Page 300: Concluding Steps

    Ê Ê Mount the support bracket and rack mounting rails in the rack as described in the "Rack Mounting Kit - RMK-F2 Drop-In" Mounting Instructions. The document is available online at http://manuals.ts.fujitsu.com (EMEA market) or http://jp.fujitsu.com/platform/server/primergy/manual/ (Japanese market). "Mounting the server in the rack" on page 60 Ê...

  • Page 301: Cabling

    Cabling Safety notes CAUTION! Always hold cables by their connectors when disconnecting them. ● Never pull on the cable to disconnect cables. Ensure that none of the cables are scraped, strained or otherwise ● damaged while replacing system components. Immediately replace cables with damaged shielding. ●...

  • Page 302: List Of Used Cables

    Cabling 16.1 List of used cables The numbers in the cable list correspond to those shown in the cabling plans. No. Name Cable number Routing Front panel module from front panel module to system T26139-Y4015-V301 cable board Front / internal USB from front panel module / USB 3.0 T26139-Y3999-V504 cable...

  • Page 303: Cabling Plans

    Cabling 16.2 Cabling plans Standard PSU Front Panel USB 3.0 Connectors Drive Bay 1 SATA ODD Slimline SATA ODD Drive Bay 2 USB Backup Drive P2/3 System Board D3239 PWR1 Drive Bay 3 PC2009 LTO 3 Backup Drive P2/3 SATA POWER FRONTPANEL Intrusion Switch USB FRONT...
  • Page 304 Cabling Redundant PSU Front Panel USB 3.0 Connectors Drive Bay 1 SATA ODD Slimline SATA ODD Drive Bay 2 USB Backup Drive P2/3 System Board D3239 PWR1 Drive Bay 3 PC2009 LTO 3 Backup Drive P2/3 SATA POWER FRONTPANEL Intrusion Switch USB FRONT SATA 5 HDD Backplane(s)
  • Page 305 Cabling Front Panel USB 2.0/3.0 Connectors Drive Bay 1 SATA ODD Drive Bay 2 USB 3.0 Backup Drive System Board D3239 FRONTPANEL Drive Bay 3 USB FRONT LTO 3 Backup Drive USB1 AUX USB1 DAT Intrusion Switch SATA 5 SATA 6 HDD Backplane(s) MLC SATA 1-4 (1x 3.5”...
  • Page 306 Cabling Front Panel Drive Bay 1 SATA ODD System Board D3239 Drive Bay 2 USB1 DAT USB Backup Drive USB1 AUX Drive Bay 3 LTO 4/5/6 Backup Drive SAS Controller Slot 3 / 2 MLC 2 MLC 1 HDD Backplanes 3.5”...
  • Page 307 Cabling Front Panel Drive Bay 1 SATA ODD System Board D3239 Drive Bay 2 USB1 DAT USB Backup Drive SATA POWER Drive Bay 3 P2/3 LT0 3 Backup Drive SAS Controller Slot 3 / 2 MLC 2 MLC 1 HDD Backplanes SAS Controller Slot 4 MLC 2...
  • Page 308 Cabling System Board D3239 Drive Bay 2 USB1 DAT USB Backup Drive USB1 AUX Drive Bay 3 SAS Controller SAS Backup Drive Slot 3 / 2 MLC 2 MLC 1 MLC SATA 1-4 HDD Backplanes 3.5” HDD BP 1x 2.5” HDD BP Figure 207: SATA cabling with up to 4 HDDs System Board D3239 Drive Bay 2...
  • Page 309 Cabling Front Panel Drive Bay 1 SATA ODD System Board D3239 Drive Bay 2 USB Backup Drive Drive Bay 3 SAS Backup Drive PCI Slot 1 HDD Backplanes 3.5” HDD BP 32-bit PCI Riser Card 2.5” HDD BP 1 Figure 209: Riser card cabling - 1 Upgrade and Maintenance Manual TX1330 M1...
  • Page 310 Cabling System Board D3239 Drive Bay 2 USB Backup Drive Drive Bay 3 SAS Backup Drive PCI Slot 1 HDD Backplanes 3.5” HDD BP 32-bit PCI Riser Card 2.5” HDD BP 1 Figure 210: Riser card cabling - 2 Upgrade and Maintenance Manual TX1330 M1...

  • Page 311: Replacing The Intrusion Switch Cable

    Cabling 16.3 Replacing the intrusion switch cable Field Replaceable Unit Hardware: 10 minutes (FRU) Tools: Phillips PH2 / (+) No. 2 screw driver 16.3.1 Preliminary steps "Locating the defective server" on page 43 Ê "Shutting down the server" on page 46 Ê...
  • Page 312 Cabling Ê Disconnect the intrusion switch cable from the system board (see circle). Ê Remove the intrusion switch cable from the cable clamps (see arrows) on the HDD cage. Figure 212: Removing the intrusion switch holder (A) Ê Remove one screw from the intrusion switch holder as shown. Replacing the intrusion switch cable is illustrated by the example of the 2.5-inch HDD model.
  • Page 313 Cabling Figure 214: Removing the intrusion switch cable (B) Ê Slide back the intrusion switch holder until it disengages from the HDD bay top cover (1). Ê Remove the intrusion switch holder (2). Upgrade and Maintenance Manual TX1330 M1...

  • Page 314: Installing The New Intrusion Switch Cable

    Cabling 16.3.3 Installing the new intrusion switch cable Figure 215: Attaching a rubber bumper to the front intrusion switch In case of rack server configurations, a rubber bumper needs to be attached to the front intrusion switch as described below. When working on a tower server, please skip this step.
  • Page 315 Cabling Figure 216: Installing the intrusion switch cable (A) Ê Place the new intrusion switch holder on the HDD bay top cover as shown (1). Ê Slide the intrusion switch holder under the front chassis rim as far as it will go (2).

  • Page 316: Concluding Steps

    Cabling Figure 218: Connecting the intrusion switch cable Ê Run the intrusion switch cable through the cable clamps (see arrows). Ê Connect the intrusion switch cable to the system board connector "Intrusion" (see circle). 16.3.4 Concluding steps "Installing the rack front cover" on page 58 (rack server) or "Installing the Ê...

  • Page 317: Appendix

    Appendix 17.1 Mechanical overview 17.1.1 Server front 2.5-inch HDD / SSD model Figure 219: Server front - 2.5-inch HDD / SSD model 2.5-inch HDD/SSD / dummy 4 ID card module 2 5.25-inch dummy module 5 ODD Front panel module including front 3 5.25-inch dummy module USB connectors Upgrade and Maintenance Manual...
  • Page 318 Appendix 3.5-inch HDD model Figure 220: Server front - 3.5-inch HDD model 1 3.5-inch HDD / dummy module 4 ID card 2 5.25-inch dummy module 5 ODD Front panel module including front 3 5.25-inch dummy module USB connectors Upgrade and Maintenance Manual TX1330 M1...

  • Page 319: Server Rear

    Appendix 17.1.2 Server rear Figure 221: Server rear (example: standard power supply) Figure 222: Server rear (example: redundant power supply) Power supply unit I/O panel System fan Optional expansion cards Upgrade and Maintenance Manual TX1330 M1...

  • Page 320: Server Interior

    Appendix 17.1.3 Server interior Figure 223: Interior (example: 2.5-inch HDD model, standard power supply) System fan SAS / SATA backplane Expansion card slots HDD / SSD drive bay Processor / heat sink Front panel module bay Accessible drive bay CMOS battery System board D3239 Memory modules BBU/FBU...
  • Page 321 Appendix Figure 224: Interior (example: 3.5-inch HDD model, redundant power supply) System fan HDD drive bay Expansion card slots Front panel module bay Processor / heat sink Accessible drive bay System board D3239 CMOS battery Power distribution board Memory modules SAS / SATA backplane Power supply units Upgrade and Maintenance Manual...

  • Page 322: Connectors And Indicators

    Appendix 17.2 Connectors and indicators 17.2.1 Connectors and indicators on the system board 17.2.1.1 Onboard connectors DIMM1B DIMM2B COM1 DIMM1A DIMM2A SATA POWER Service Management LAN/ USB 9/10 Intel FAN1 Shared LAN/ USB 7/8 i210 Standard LAN/ Intel USB 5/6 i217 SATA1-4 Micro...
  • Page 323 Appendix No. Print Description PWR1 ATX power supply connector Power distribution for SAS / SATA backplanes and SATA POWER accessible drives PC2009 Power management connector FRONTPANEL Front panel Power supply connector USB FRONT Connector for front USB FAN1 SYS Connector for system fan SATA MLC connector for 3.5-inch HDD SATA MLC1 configurations...

  • Page 324: Component Leds

    Appendix 17.2.1.2 Onboard indicators and controls DIMM1B DIMM2B COM1 DIMM1A DIMM2A SATA POWER Service Management LAN/ USB 9/10 Shared LAN/ Intel FAN1 USB 7/8 i210 Standard LAN/ Intel USB 5/6 i217 SATA1-4 Micro Slot 4 PCIe x8 Indicate USB1AUX iRMC S4 Intel Slot 3 PCIe x8 C224...
  • Page 325 Appendix Indicator Status Description no critical event (non CSS component) orange on prefailure detected (non CSS component) non CSS component failure Possible reasons: (Global Error orange LED) – sensors report overheating flashing – sensor is defective – CPU error – software reports an error no critical event (CSS component) yellow on prefailure detected (CSS component)

  • Page 326: I/O Panel Connectors

    Appendix 17.2.1.3 I/O panel connectors Figure 227: I/O panel connectors Management LAN connector, for iRMC S4 server management function Shared LAN connector (LAN1) Standard LAN connector (LAN2) USB 3.0 connectors USB 2.0 connectors Video connector (VGA) Serial connector COM1 Depending on BIOS settings, the shared LAN connector may also be used as a management LAN connector.

  • Page 327: I/O Panel Indicators

    Appendix 17.2.1.4 I/O panel indicators Figure 228: I/O panel indicators Indicator Status Description green on LAN connection established no LAN connection link/transfer green flashing data transfer in progress yellow on traffic a transfer rate of 1 Gbit/s 2 LAN speed green on traffic a transfer rate of 100 Mbit/s traffic a transfer rate of 10 Mbit/s...

  • Page 328: Psu Indicator (Only Hot-Plug Psus)

    Appendix 17.2.1.5 PSU indicator (only hot-plug PSUs) Figure 229: PSU indicator Indicator Status Description Server is switched on and functioning green on properly Server is switched off, main voltage is green flashing present (Standby mode) operating status PSU failure (over / under voltage, over orange on temperature or fan failure) orange flashing...

  • Page 329: Diagnostic Indicators

    Appendix 17.2.2 Connectors and indicators on the front panel 17.2.2.1 Front panel controls and indicators Figure 230: Front panel controls and indicators Local diagnostic indicators Pos. Indicator Status Description HDD error HDD / SSD, SAS / SATA backplane or orange on indicator RAID controller failure detected Hot-plug power supply unit failure detected...
  • Page 330 Appendix Status indicators Pos. Indicator Status Description blue on Localizes the server Identification blue indicator Local monitor off flashing no critical event (CSS component) yellow on prefailure detected (CSS component) CSS indicator yellow CSS component failure flashing no critical event (non CSS component) Global error orange on prefailure detected (non CSS component) indicator...
  • Page 331 Appendix Pos. Indicator Status Description Power on delay After shutting down, the server cannot be switched on again right away. If the On / Off button is yellow on pressed right after shutting down the server, the power-on indicator will light up yellow until the delay period ends and the server will boot.
  • Page 332 Appendix Front panel connectors Pos. Description blue USB 3.0 connector black USB 2.0 connector Upgrade and Maintenance Manual TX1330 M1...

  • Page 333: Onboard Settings

    Appendix 17.3 Onboard settings SATA POWER Service Management LAN/ USB 9/10 Shared LAN/ Intel FAN1 i210 USB 7/8 Standard LAN/ Intel USB 5/6 i217 SATA1-4 Micro Slot 4 PCIe x8 Indicate USB1AUX iRMC S4 Intel Slot 3 PCIe x8 C224 USB1 Slot 2 PCIe x4 Battery...

  • Page 334: Minimum Startup Configuration

    Appendix 17.4 Minimum startup configuration Field Replaceable Units (FRU) If the server does not start up or other problems occur, it may be necessary to take the system down to its most basic configuration in order to isolate the defective component. The minimum startup configuration consists of the following components and cables: Component...
  • Page 335 Appendix CAUTION! Since the fan module is not included in the minimum startup configuration, the server must be shut down immediately after the diagnostic process is complete (POST phase has been passed). The minimum startup configuration must be used exclusively for diagnostic purposes by maintenance personnel, never in daily operation! Upgrade and Maintenance Manual...
  • Page 336 Appendix Upgrade and Maintenance Manual TX1330 M1...

Table of Contents