Fujitsu PRIMERGY TX1310 M5 Upgrade And Maintenance Manual
  1. Manuals
  2. Brands
  3. Fujitsu Manuals
  4. Server
  5. PRIMERGY TX1310 M5
  6. Upgrade and maintenance manual

Fujitsu PRIMERGY TX1310 M5 Upgrade And Maintenance Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Upgrade and Maintenance Manual - English
FUJITSU Server PRIMERGY TX1310 M5
Upgrade and Maintenance Manual
03/2022

Advertisement

Table of Contents
loading

Related Manuals for Fujitsu PRIMERGY TX1310 M5

Summary of Contents for Fujitsu PRIMERGY TX1310 M5

  • Page 1 Upgrade and Maintenance Manual - English FUJITSU Server PRIMERGY TX1310 M5 Upgrade and Maintenance Manual 03/2022...
  • Page 2 All hardware and software names used are trademarks of their respective manufacturers. The contents of this manual may be revised without prior notice. – Fujitsu assumes no liability for damages to third party copyrights or other rights arising from – the use of any information in this manual.
  • Page 3 Before reading this manual For your safety This manual contains important information for safely and correctly using this product. Carefully read the manual before using this product. Pay particular attention to the accompanying manual "Safety Notes and Regulations" and ensure that these safety notes are understood before using the product.
  • Page 4 Please consult the sales staff of Fujitsu if intending to use this product for high safety use. Measures against momentary voltage drop This product may be affected by a momentary voltage drop in the power supply caused by lightning.
  • Page 5 HDD, see the following internet address: https://jp.fujitsu.com/platform/server/primergy/harddisk/ Only for Japan: Shielded LAN cables should be used in this product. UK Importer information Fujitsu Services Limited 22 Baker Street, London, W1U 3BW, United Kingdom TX1310 M5 Upgrade and Maintenance Manual...
  • Page 6 Version history Issue Issue date Description number V 1.0 11/2021 Initial release 03/2022 cable plan updated Upgrade and Maintenance Manual TX1310 M5...

  • Page 7: Table Of Contents

    Content Introduction Concept and target groups of this manual Notational conventions Before you start Basic information 2.1.1 Proceeding 2.1.2 Advanced Thermal Design (ATD) 2.1.3 Installing optional components Classification of procedures 2.2.1 Assignment of unit categories 2.2.2 Customer Replaceable Units (CRU) 2.2.3 Upgrade and Repair Units (URU) 2.2.4...
  • Page 8 Content 3.2.4 Batteries 3.2.5 Working with optical disk drives (ODDs) and media 3.2.6 Laser information 3.2.7 Modules with Electrostatic-Sensitive Devices (ESD modules) 3.2.8 Transporting the server 3.2.9 Installing the server in the rack 3.2.10 Other important information CE conformity FCC Class A Compliance Statement Environmental protection Basic hardware procedures Using diagnostic information...
  • Page 9 Content Connecting the power cord Switching on the server 4.10 Installing the bay cover 4.11 Locking the server Basic software procedures Starting the maintenance task 5.1.1 Suspending BitLocker functionality 5.1.2 Removing backup and optical disk media 5.1.3 Verifying and configuring the backup software solution Completing the maintenance task 5.2.1 Updating or recovering the BIOS...
  • Page 10 Content Hard disk drives (HDD) Safety notes Basic information 2.5-inch HDD/SSD configurations 7.3.1 Installing a 2.5-inch HDD module 7.3.2 Removing a 2.5-inch HDD module 7.3.3 Replacing a 2.5-inch HDD module 3.5-inch HDD configurations 7.4.1 Installing a 3.5-inch HDD module 7.4.2 Removing a 3.5-inch HDD module 7.4.3 Replacing a 3.5-inch HDD module...
  • Page 11 Content Replacing an expansion card Main memory 10.1 Safety notes 10.2 Basic informations 10.3 Installing memory modules 10.4 Removing memory modules 10.5 Replacing memory modules Processor (CPU) 11.1 Safety notes 11.2 Basic information 11.3 Upgrading or replacing the CPU 11.4 Replacing the heat sink 11.5 Handling the protectice cover...
  • Page 12 Content 12.4.2 Removing the RDX backup drive 12.4.3 Replacing the RDX backup drive Front panel and front USB Serial interface 14.1 Safety notes 14.2 Installing the serial interface 14.3 Removing the serial interface 14.4 Replacing the serial interface System board and components 15.1 Safety notes 15.2...
  • Page 13 Content Cables 16.1 Safety notes 16.2 Basic information 16.3 Replacing the system cable (accessible drives / top HDD cage) 16.4 Replacing the HDD cable (bottom HDD cage) Appendix A 17.1 Mechanical overview 17.1.1 Server front 17.1.2 Server rear 17.1.3 Server interior 17.2 Connectors and indicators 17.2.1...
  • Page 14 Content Upgrade and Maintenance Manual TX1310 M5...

  • Page 15: Introduction

    Introduction Concept and target groups of this manual This upgrade and maintenance manual provides instructions for the following procedures: – Upgrading the server configuration by adding optional hardware components. – Upgrading the server configuration by replacing existing hardware components with superior ones. –...
  • Page 16 Introduction "Quotation marks" Indicate names of chapters and terms that are being emphasized. ▶ Describes activities that must be performed in the order shown. [Abc] Indicates keys on the keyboard. Pay particular attention to texts marked with this CAUTION symbol. Failure to observe this warning may endanger your life, destroy the system or lead to the loss of data.

  • Page 17: Before You Start

    Before you start Basic information 2.1.1 Proceeding Before you start any upgrade or maintenance task, proceed as follows: ▶ Carefully read the safety instructions, see "Important information" on page ▶ Make sure that all necessary manuals are available, see "About availability of manuals"...

  • Page 18: Installing Optional Components

    For Japan: https://www.fujitsu.com/jp/products/computing/servers/primergy/ Please contact your local Fujitsu customer service partner for details on how to order expansion kits or spare parts. Classification of procedures 2.2.1 Assignment of unit categories The complexity of maintenance procedures varies significantly.

  • Page 19: Customer Replaceable Units (Cru)

    Before you start Please ask your local Fujitsu service center for more information. 2.2.2 Customer Replaceable Units (CRU) Customer Replaceable Units (CRU) Customer Replaceable Units are intended for customer self service. Components that the customer is entitled to replace may differ according to the service form in his country.

  • Page 20: Field Replaceable Units (Fru)

    CAUTION Maintenance procedures involving Field Replaceable Units must be performed exclusively by Fujitsu service personnel or technicians trained by Fujitsu. Please note that unauthorized interference with the system will void the warranty and exempt the manufacturer from all liability. Upgrade and Maintenance Manual...

  • Page 21: Average Task Duration

    – CPU (replacements) – System board – Standard PSU – Trusted Platform Module (TPM) Please ask your local Fujitsu service center for more information. Average task duration Hardware: 10 minutes The average task duration including preliminary and concluding steps is indicated at the beginning of each procedure next to the procedure class.

  • Page 22: Tools You Need At Hand

    When preparing the maintenance task, ensure that all required manuals are available, see 2.5.2. Ensure to store all printed manuals enclosed with your server in a save place for future reference. Unless stated otherwise, all manuals are available online at: https://support.ts.fujitsu.com/ For Japan: https://www.fujitsu.com/jp/products/computing/servers/primergy/manual/ Upgrade and Maintenance Manual TX1310 M5...

  • Page 23: List Of Documents

    Important safety information, available online, Regulations" manual or as a printed copy "安全上のご注意" for Japan "FUJITSU Server Information how to install, set up and operate PRIMERGY TX1310 M5 your server, available online Operating Manual" "FUJITSU Server Instructions for upgrading the server PRIMERGY TX1310 M5...
  • Page 24 "保証書" for Japan printed copy "Returning used devices" Recycling and contact information, available manual online at https://ts.fujitsu.com/recycling, or as a printed copy "Service Desk" leaflet Not applicable in Japan and other countries that "サポート＆サービス" for have different regulations for recycling...

  • Page 25: Important Information

    Important information Introduction In this chapter you will find essential information regarding safety when working on your server. Depending on your server or the installed options some information is not valid for your server. CAUTION ▶ Before installing and starting up a server, please observe the safety instructions listed in the following section.

  • Page 26: Before Starting Up

    Important information ▶ Only valid for non hot-plug components Before installing/removing internal components to/from the server, turn off the server, all peripheral devices, and any other connected devices. Also unplug all power cords from the power outlet. Failure to do so can cause electric shock or damage.
  • Page 27 Important information ▶ If a DC power cord is used, the server must be connected to a proper DC source and earth ground stud/end. ▶ Ensure that the server is connected to a properly grounded power outlet close to the server. ▶...
  • Page 28 Important information ▶ Proper operation of the server (in accordance with IEC 60950-1/62368-1 resp. EN 60950-1/62368-1) is only ensured if the server is completely assembled and the rear covers for the installation slots have been fitted (electric shock, cooling, fire protection, interference suppression). ▶...

  • Page 29: Batteries

    Important information ▶ Install the screw removed during installation/detaching internal options in former position. To use a screw of the different kind can cause a breakdown of equipment. ▶ The procedure of installation on this notes might change depending on a configuration of option.
  • Page 30 Important information CAUTION ▶ Only use CDs/DVDs/BDs that are in perfect condition, in order to prevent data loss, equipment damage and injury. ▶ Check each CD/DVD/BD for damage, cracks, breakages etc. before inserting it in the drive. Note that any additional labels applied may change the mechanical properties of a CD/DVD/BD and cause imbalance and vibrations.

  • Page 31: Laser Information

    Important information ▶ Do not bend or place heavy objects on CDs/DVDs/BDs. ▶ Do not write with ballpoint pen or pencil on the label (printed) side. ▶ Do not attach stickers or similar to the label side. Doing so may cause rotational eccentricity and abnormal vibrations.
  • Page 32 Important information Figure 1: ESD label The ESD label can be different. When you handle ESD modules, you must always observe the following points: ▶ Switch off the server and remove the power plugs from the power outlets before installing or removing ESD modules. ▶...

  • Page 33: Transporting The Server

    Important information 3.2.8 Transporting the server CAUTION ▶ Only transport the server in its original packaging or in packaging that protects it from impacts and jolts. In Japan and APAC, transporting the server in its original packaging does not apply. ▶...

  • Page 34: Installing The Server In The Rack

    Important information 3.2.9 Installing the server in the rack CAUTION ▶ For safety reasons, at least 2 people are required to install the server in the rack because of its weight and size. (For Japan, see "安全上のご注意".) ▶ Never lift the server into the rack using the QRLs on the front panel. ▶...

  • Page 35: Ce Conformity

    ▶ Select the subclass, e.g. "Tower servers". ▶ Select your server, e.g. "PRIMERGY TX1310 M5". ▶ Select the document, e.g. "CE Cert PRIMERGY TX1310 M5". FCC Class A Compliance Statement If there is an FCC statement on the device, it applies to the products covered in this manual, unless otherwise specified herein.

  • Page 36: Environmental Protection

    ▶ Consult the dealer or an experienced radio/TV technician for help. Fujitsu is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Fujitsu. The correction of interferences caused by such unauthorized modification, substitution or attachment will be the responsibility of the user.
  • Page 37 Important information Packaging information This packaging information does not apply in Japan and APAC. Do not throw away the packaging. You may need it later for transporting the server. If possible, the equipment should only be transported in its original packaging. Information on handling consumables Please dispose of printer consumables and batteries in accordance with the applicable national regulations.
  • Page 38 More information can be found at: https://ts.fujitsu.com/recycling Details regarding the return and recycling of devices and consumables within Europe can also be found in the "Returning used devices" manual, via your local Fujitsu branch, or at: https://ts.fujitsu.com/recycling Upgrade and Maintenance Manual TX1310 M5...

  • Page 39: Basic Hardware Procedures

    Using diagnostic information 4.1.1 Proceeding Use the Fujitsu ServerView Suite management software to plan the upgrade or replacement of hardware components. It is recommended to prepare local maintenance tasks using remote diagnostics procedures, see the "ServerView Suite Local Service Concept (LSC)"...

  • Page 40: Removing The Bay Cover

    Basic hardware procedures ▶ Remove the key ring with keys from the server rear. Figure 3: Unlocking the server ▶ Insert the key into the lock on the server front. ▶ Turn the key clockwise to unlock the drive bay cover (1). ▶...

  • Page 41: Shutting Down The Server

    Basic hardware procedures Figure 4: Folding out the bay cover ▶ Press up on the locking latch and fold out the bay cover. ▶ Remove the bay cover. Shutting down the server CAUTION ▶ For more information, see "Important information" on page ▶...

  • Page 42: Disconnecting The Power Cord

    Basic hardware procedures Figure 5: On/Off button ▶ Shut down the server by pressing the On/Off button (1). If the system is running an ACPI-compliant operating system (OS), pressing the On/Off button will perform a graceful shutdown. Disconnecting the power cord Before disconnecting the power cord the server must be shut down.

  • Page 43: Getting Access To The Component

    Basic hardware procedures Figure 6: Disconnecting the power cords ▶ Disconnect the power cord from the PSU (1). ▶ If applicable, disconnect the power supply of the monitor (2). Getting access to the component 4.6.1 Safety notes CAUTION ▶ Before removing or installing covers (except the bay cover), turn off the server, all peripheral devices, and any other connected devices, and unplug all power cables from the outlet.

  • Page 44: Removing The Side Cover

    Basic hardware procedures 4.6.2 Removing the side cover Figure 7: Removing the side cover ▶ Pull up on the locking lever (1). ▶ Open the side cover (2). ▶ Remove the side cover (3). 4.6.3 Removing the front cover CAUTION ▶...
  • Page 45 Basic hardware procedures Figure 8: Removing the ID card ▶ Remove the ID card before opening and removing the front cover. ▶ Store the ID card on a safe place. Figure 9: Removing the front cover (A) ▶ Disengage the four locking tabs of the front cover (see circles) by puling it forwards.

  • Page 46: Removing The Top Hdd Cage

    Basic hardware procedures Figure 10: Removing the front cover (B) ▶ Carefully rotate open (1) and unhook the front cover (2). 4.6.4 Removing the top HDD cage Depending on accessibility, it may be required to pull out the top HDD cage for maintenance purposes.
  • Page 47 Basic hardware procedures Removing the HDD cage door Figure 11: Pulling up the lever ▶ Pull up the lever of the HDD cage door (see arrow). Figure 12: Folding down the HDD cage door TX1310 M5 Upgrade and Maintenance Manual...

  • Page 48: Removing The System Board Tray

    Basic hardware procedures ▶ Fold down the HDD cage door. ▶ Remove the HDD cage door. Extending the HDD cage out of the chassis Figure 13: Extending the HDD cage ▶ Lift up the locking lever on the HDD cage (1) and pull out the HDD cage (2). 4.6.5 Removing the system board tray ▶...
  • Page 49 Basic hardware procedures Figure 14: System board tray - Location of screws ▶ Remove five screws from the chassis (see circles). Figure 15: Removing the system board tray ▶ Pull the system board tray out of the chassis. TX1310 M5 Upgrade and Maintenance Manual...

  • Page 50: Reassembling

    Basic hardware procedures Reassembling 4.7.1 Safety notes CAUTION ▶ Before attaching the covers, make sure no unnecessary parts or tools are left inside the server. ▶ Before switching on the server, make sure the side cover is closed. In order to comply with applicable EMC regulations (regulations on electromagnetic compatibility) and satisfy cooling requirements, the server must not run while the side cover is removed.
  • Page 51 Basic hardware procedures Figure 17: System board tray - Location of screws ▶ Fasten the system board tray to the chassis with five screws (see circles). ▶ Connect all cables on their place at the system board. TX1310 M5 Upgrade and Maintenance Manual...

  • Page 52: Installing The Top Hdd Cage

    Basic hardware procedures 4.7.3 Installing the top HDD cage Sliding the top HDD cage into the chassis Figure 18: Pushing the HDD cage in and folding down the lever ▶ Push the HDD cage back into the chassis (1) and fold down the lever (2). Upgrade and Maintenance Manual TX1310 M5...
  • Page 53 Basic hardware procedures Installing the HDD cage door Figure 19: Installing the HDD cage door ▶ Install the HDD cage door and fold it up. Figure 20: Folding down the lever ▶ Fold down the lever of the HDD cage door. TX1310 M5 Upgrade and Maintenance Manual...

  • Page 54: Installing The Front Cover

    Basic hardware procedures Installing the bay cover ▶ Install the bay cover, see "Installing the bay cover" on page 4.7.4 Installing the front cover Figure 21: Installing the front cover (A) ▶ Hook the three tabs on the front cover into the notches of the front bezel (see circles).
  • Page 55 Basic hardware procedures Figure 22: Installing the front cover (B) ▶ Carefully close the front cover. Make sure that all three locking latches properly engage. Figure 23: Installing the ID card ▶ Insert hte ID card. TX1310 M5 Upgrade and Maintenance Manual...

  • Page 56: Installing The Side Cover

    Basic hardware procedures 4.7.5 Installing the side cover Figure 24: Installing the side cover ▶ Hook the side cover in the bottom side cant of the chassis (1). ▶ Push the side cover against the chassis until the locking mechanism engages (2).

  • Page 57: Switching On The Server

    Basic hardware procedures Figure 25: Connecting the power cords ▶ If applicable, connect the power cord for the monitor to the lower socket (1). ▶ Connect the power cord of the PSU to the upper socket (2). ▶ Connect the mains plug to a grounded mains outlet in the in-house power supply network.

  • Page 58: Installing The Bay Cover

    Basic hardware procedures Figure 26: On/Off button ▶ Press the On/Off button to start up the server (1). ▶ Ensure that the power-on indicator is lit green. For more information see "Indicators on the front panel" on page 230. ▶ Perform the required procedures described in the concluding steps of each upgrade or maintenance task.

  • Page 59: Locking The Server

    Basic hardware procedures Figure 28: Installing the bay cover ▶ Hook the four tabs on the upper side of the bay cover into the notches in the front bezel (1, see also circles in Figure 27). ▶ Fold down the bay cover until it locks in place (2). 4.11 Locking the server Figure 29: Locking the server...
  • Page 60 Basic hardware procedures ▶ Insert the key into the lock on the server front (1). ▶ Turn the key counter-clockwise to lock the drive bay cover (2). ▶ Remove the key. ▶ Store the key at a secure place to prevent unauthorized access. Upgrade and Maintenance Manual TX1310 M5...

  • Page 61: Basic Software Procedures

    Basic software procedures Starting the maintenance task 5.1.1 Suspending BitLocker functionality BitLocker Drive Encryption provides protection for OS and data drives by encrypting the contents and requiring users to authenticate their credentials to access the information. In the scenario described here, BitLocker uses the compatible Trusted Platform Module (TPM) to detect if the computer's startup process has been modified from its original state.
  • Page 62 BitLocker setup wizard, it may be necessary to modify the BitLocker Group Policy settings. For more information on how to suspend BitLocker drive encryption, see the Microsoft TechNet library at: https://technet.microsoft.com/library/cc731549.aspx For more information, see the Fujitsu web pages. Upgrade and Maintenance Manual TX1310 M5...

  • Page 63: Removing Backup And Optical Disk Media

    5.2.1 Updating or recovering the BIOS After replacing the system board or a CPU, it is essential to upgrade the BIOS to the latest version. The latest BIOS version are available from the Fujitsu support internet pages at: https://ts.fujitsu.com/support/ TX1310 M5...

  • Page 64: Reconfiguring The Backup Software Solution

    Basic software procedures For Japan: https://www.fujitsu.com/jp/products/computing/servers/primergy/downloads/ Fujitsu does not assume responsibility for any damage done to the server or for the loss of any data resulting from BIOS updates.. For Japan, follow the instructions provided separately. BIOS flash procedure ▶ Perform the BIOS flash procedure as described in the "BIOS Setup Utility"...

  • Page 65: Enabling Replaced Components In The Bios

    Basic software procedures More information on suitable backup software solutions and related documentation is available from the Fujitsu web pages. 5.2.3 Enabling replaced components in the BIOS When a CPU, an expansion card, or a memory module fails, the defective component will be set to Disabled or Failed in the BIOS.

  • Page 66: Viewing The System Event Log (Sel)

    Basic software procedures If a Linux/VMware OS is used and the hardware clock has been configured as UTC (Universal Time, Coordinated) in the OS, the BMC local time may not be mapped correctly. ▶ After replacing the system board, ask the system administrator whether the RTC or UTC time standard is to be used as system time.

  • Page 67: Updating The Nic Configuration File In A Linux/Vmware Os

    Basic software procedures 5.2.6 Updating the NIC configuration file in a Linux/ VMware OS In order to prevent errors caused by changing network device names (eth<x>), it is recommended to store the MAC address (hardware address) of a network interface card in the related NIC configuration file of the Linux/VMware OS. When replacing a network controller or the system board with onboard LAN controllers in a server running Linux/VMware OS, the MAC address will change but not automatically be updated in the definition file.

  • Page 68: Resuming Bitlocker Functionality

    Basic software procedures ▶ Save and close the definition file. ▶ For the changes to take effect, you need to reboot the network by entering the following command: # service network restart If the system board or network controller offers multiple LAN ports, it is necessary to update the remaining ifcfg-eth<x>...

  • Page 69: Performing A Raid Array Rebuild

    For more information on how to resume BitLocker drive encryption, see the Microsoft TechNet library at: https://technet.microsoft.com/library/cc731549.aspx For more information, see the Fujitsu web pages. 5.2.8 Performing a RAID array rebuild After replacing an HDD that has been combined into a RAID array, RAID rebuild will be performed unattended as a background process.

  • Page 70: Looking Up For Mac/Wwn Addresses

    Basic software procedures Figure 30: Progress bar (RAID array rebuild) CAUTION The system is now operational, however, data redundancy will not be available until the RAID array rebuild is complete. Depending on the HDD capacity the overall process can take up to several hours, in some cases even days.

  • Page 71: Using The Chassis Id Prom Tool

    After replacing the Chassis ID EPROM, system information has to be entered using the Chassis ID Prom tool. The tool and further instructions are available to maintenance personnel from the Fujitsu web pages: https://partners.ts.fujitsu.com/com/service/ps/Servers/PRIMERGY/ ▶ Select your PRIMERGY system from the main area of the page.
  • Page 72 Basic software procedures ▶ Ensure that the controllers have been assigned as primary or secondary according to your requirements. For more information, see the relevant LAN driver manual. After replacing a system board The following procedure must be done for each system board that is replaced.

  • Page 73: Power Supply Unit (Psu)

    Power supply unit (PSU) Safety notes CAUTION ▶ Do not disassemble the PSU. Doing so may cause electric shock. ▶ Areas around the PSU may remain extremely hot after shutdown. After shutting down the server, wait for hot components to cool down before removing the PSU.
  • Page 74 Power supply unit (PSU) ▶ "Disconnecting the power cord" on page ▶ "Getting access to the component" on page ▶ "Removing the top HDD cage" on page Removing the standard PSU ▶ Push the backup drive somewhat to the front to get more space, see "Removing the RDX backup drive"...
  • Page 75 Power supply unit (PSU) Figure 32: Removing the screws ▶ Remove seven screws from the PSU and the chassis (see circles). Figure 33: Pulling out the system board tray by 1-2 cm ▶ Pull the system board tray out of the chassis by 1-2 cm. TX1310 M5 Upgrade and Maintenance Manual...
  • Page 76 Power supply unit (PSU) Figure 34: Removing the PSU ▶ Slide the PSU to the right about 2 cm to disengage the locking mechanism (1). ▶ Lift the PSU about 4 cm (2) and remove it out of the chassis in a slight angle (3).
  • Page 77 Power supply unit (PSU) Installing the standard PSU Figure 35: Inserting the PSU ▶ Insert the PSU into the chassis in a slight angle (1) and position it in place (2). ▶ Slide the PSU towards the rear of the chassis as far as it will go (3). Figure 36: Sliding the system board tray into the chassis ▶...
  • Page 78 Power supply unit (PSU) Figure 37: Fastening the screws ▶ Fasten the PSU and the chassis with seven screws (see circles). Figure 38: Connecting the power cable ▶ Connect the power cable to the system board connector "PWR1". ▶ Push back the backup drive until it snaps into place. Upgrade and Maintenance Manual TX1310 M5...
  • Page 79 Power supply unit (PSU) Concluding steps ▶ "Installing the top HDD cage" on page ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶ "Switching on the server" on page ▶ "Installing the bay cover" on page ▶ "Locking the server"...
  • Page 80 Power supply unit (PSU) Upgrade and Maintenance Manual TX1310 M5...

  • Page 81: Hard Disk Drives (Hdd)

    Hard disk drives (HDD) Safety notes CAUTION ▶ Before removing several HDD/SSD modules, make sure that all HDD/SSD modules can be reinstalled into their original bay. Otherwise, data may be lost. ▶ Do not touch the circuitry on boards or soldered parts. Hold circuit boards by their metallic areas or edges.

  • Page 82: Basic Information

    Hard disk drives (HDD) Basic information General equipping rules – HDDs with different capacities are installed from highest to lowest capacity. – HDDs with different rotation speeds are installed from highest to lowest speed. – Maximum configuration: 4x 3.5-inch HDDs Mounting order Figure 39: 3.5-inch HDD mounting order HDD1...

  • Page 83: Inch Hdd/Ssd Configurations

    Hard disk drives (HDD) SATA connectivity Controller Channel Connection PCI SATA controller Drives 1-4 2.5-inch HDD/SSD configurations 7.3.1 Installing a 2.5-inch HDD module Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: Phillips PH2 / (+) No. 2 screw driver Preliminary steps ▶...
  • Page 84 Hard disk drives (HDD) Figure 40: Removing the screws from the 3.5-inch HDD carrier ▶ Remove the four screws from the 3.5-inch HDD carrier. Figure 41: Attaching the 2.5-inch HDD to the 3.5-inch HDD carrier ▶ Fasten the 4 screws to the 3.5-inch HDD carrier and attach the HDD to the carrier (see circles).
  • Page 85 Hard disk drives (HDD) Figure 42: Installing a 2.5-inch HDD ▶ Insert the HDD into its drive bay. ▶ Slide the HDD into its drive bay until the Easyrails click in place. ▶ When using a RAID array, add the additional HDD/SSD to the RAID array. Configuring the RAID array, refer to the documentation of the RAID controller, used in your configuration, see "Documentation overview"...

  • Page 86: Removing A 2.5-Inch Hdd Module

    Hard disk drives (HDD) 7.3.2 Removing a 2.5-inch HDD module Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: Phillips PH2 / (+) No. 2 screw driver Preliminary steps ▶ If the HDD module to be removed is combined into a RAID array, please proceed as follows: RAID level Procedure...
  • Page 87 Hard disk drives (HDD) Removing a 2.5-inch HDD HDDs on the bottom and HDDs on the front can be removed in the same way. Figure 43: Removing a 2.5-inch HDD ▶ Pull the HDD carrier completely out of its drive bay. Figure 44: Detaching the 2.5-inch HDD from the 3.5-inch HDD carrier ▶...

  • Page 88: Replacing A 2.5-Inch Hdd Module

    Hard disk drives (HDD) Concluding steps ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶ "Switching on the server" on page ▶ "Installing the bay cover" on page ▶ "Locking the server" on page 7.3.3 Replacing a 2.5-inch HDD module Upgrade and Repair Unit Hardware: 5 minutes (URU)

  • Page 89: Inch Hdd Configurations

    Hard disk drives (HDD) Installing the new 2.5-inch HDD ▶ Install the HDD, see "Installing a 2.5-inch HDD" on page Concluding steps ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶ "Switching on the server" on page ▶...
  • Page 90 Hard disk drives (HDD) Removing Easyrail out of the upper HDD bay Figure 45: Removing the Easyrails out of the bay ▶ Press in the green handle on the Easyrail (1) and pull the rail out of the desired 3.5-inch HDD drive bay (2). Easyrails can be different (see figures).
  • Page 91 Hard disk drives (HDD) Figure 47: Attaching the Easyrails ▶ Attach an Easyrail each side of the HDD. Figure 48: Inserting the 3.5-inch HDD ▶ Insert the HDD into its drive bay. ▶ Slide the HDD into its drive bay until the Easyrails click in place. TX1310 M5 Upgrade and Maintenance Manual...

  • Page 92: Removing A 3.5-Inch Hdd Module

    Hard disk drives (HDD) ▶ When using a RAID array, add the additional HDD/SSD to the RAID array. Configuring the RAID array, refer to the documentation of the RAID controller, used in your configuration, see "Documentation overview" on page Concluding steps ▶...
  • Page 93 Hard disk drives (HDD) RAID level Procedure RAID 0 Only remove an HDD module combined in a RAID 0 array if defective. CAUTION RAID 0 provides no data redundancy. In case of an HDD module is defect, all data are lost! RAID 1 Removing an HDD module from a RAID 1 array will not result in data loss.
  • Page 94 Hard disk drives (HDD) Removing a 3.5-inch HDD Figure 49: Removing a 3.5-inch HDD ▶ Press in the green handles on the Easyrails (1) to disengage the locking mechanism. ▶ Pull the HDD completely out of its drive bay (2). Figure 50: Detaching the Easyrails ▶...

  • Page 95: Replacing A 3.5-Inch Hdd Module

    Hard disk drives (HDD) Inserting Easyrails in the upper HDD bay Store unused Easyrails inside their drive bays to have them at hand if needed. Figure 51: Inserting the Easyrails into their HDD bay ▶ Push the Easyrails completely into the bay (1). ▶...
  • Page 96 Hard disk drives (HDD) CAUTION All HDD/SSD modules (drives) must be uniquely identified so that they can be reinstalled in their original bays later. If this is not done, existing data can be lost. Preliminary steps ▶ "Unlocking the server" on page 39 ▶...

  • Page 97: Fans

    Fans Safety notes CAUTION ▶ Do not damage or modify internal cables or devices. Doing so may cause a device failure, fire, or electric shock. ▶ Devices and components inside the server remain hot after shutdown. After shutting down the server, wait for hot components to cool down before installing or removing internal options.

  • Page 98: Replacing The Rear Fan

    Fans Figure 52: Positions of the system fans Rear fan (Fan2 SYS) Front fan (Fan1 SYS) CPU fan (implemented in the heat sink) The CPU fan is implemented in the heat sink. When the CPU fan is defective, the heat sink must be replaced, see "Replacing the heat sink"...
  • Page 99 Fans Preliminary steps ▶ "Unlocking the server" on page 39 ▶ "Removing the bay cover" on page 40 ▶ "Shutting down the server" on page 41 ▶ "Disconnecting the power cord" on page ▶ "Getting access to the component" on page ▶...
  • Page 100 Fans Figure 54: Removing the rear fan ▶ Extend the defective rear fan somewhat (see arrow). ▶ Cut through the four rubber rivets between the rear fan and the chassis using a diagonal pliers in sequence 1-4. Upgrade and Maintenance Manual TX1310 M5...
  • Page 101 Fans Installing the new rear fan Figure 55: Inserting new rubber rivets ▶ Lead the four rubber rivets through the screw holes on the rear chassis wall. ▶ Pull tight until the sockets on the rubber rivets properly engage with the rear chassis wall.
  • Page 102 Fans Figure 56: Installing the rear fan ▶ Lead the loose ends of the rubber rivets through the four screw holes on the new rear fan. ▶ Pull tight until the expanding plug on the rubber rivet engages with the fan (see close-up).
  • Page 103 Fans Figure 57: Cutting off the rubber rivets ▶ Cut off the loose ends of the four rubber rivets as shown. TX1310 M5 Upgrade and Maintenance Manual...
  • Page 104 Fans Figure 58: Connecting the rear fan cable ▶ Connect the rear fan cable to system board connector "Fan2 (SYS)". ▶ Install the heat sink, see "Installing the heat sink" on page 146. Concluding steps ▶ "Installing the top HDD cage" on page ▶...

  • Page 105: Replacing The Front Fan

    Fans Replacing the front fan Upgrade and Repair Unit Hardware: 15 minutes (URU) Tools: Phillips PH2 / (+) No. 2 screw driver Preliminary steps ▶ "Unlocking the server" on page ▶ "Removing the bay cover" on page ▶ "Shutting down the server" on page ▶...
  • Page 106 Fans Removing the defective front fan Figure 59: Disconnecting the front fan cable ▶ Disconnect the front fan cable from system board connector "Fan1 (SYS)". Upgrade and Maintenance Manual TX1310 M5...
  • Page 107 Fans Figure 60: Loosening the screws ▶ Loosen the four screws from the front fan air outlet (see circles). Figure 61: Removing the front fan TX1310 M5 Upgrade and Maintenance Manual...
  • Page 108 Fans ▶ Remove the front fan. Installing the new front fan Figure 62: Installing the front fan ▶ Install the front fan. Upgrade and Maintenance Manual TX1310 M5...
  • Page 109 Fans Figure 63: Fastening the screws ▶ Fasten the four screws to the front fan (see circles). Screw torque: under 0.6 Nm. TX1310 M5 Upgrade and Maintenance Manual...
  • Page 110 Fans Figure 64: Connecting the front fan cable ▶ Connect the front fan cable to system board connector "Fan1 (SYS)". Concluding steps ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶ "Switching on the server" on page ▶...

  • Page 111: Expansion Cards

    Expansion cards Safety notes CAUTION ▶ Do not damage or modify internal cables or devices. Doing so may cause a device failure, fire, or electric shock. ▶ Devices and components inside the server remain hot after shutdown. After shutting down the server, wait for hot components to cool down before installing or removing internal options.

  • Page 112: Basic Information

    Expansion cards Basic information Figure 65: PCI slot overview PCI slot Type Description PCIe x1 PCIe x1 slot Gen 3 (notched)(mechanically x4) PCIe x4 PCIe x4 slot Gen 3 (notched)(mechanically x4) PCIe x4 PCIe x4 slot Gen 3 (notched) (mechanically x4) PCIe x16 PCIe x16 slot Gen 4 (mechanically x16) Upgrade and Maintenance Manual...

  • Page 113: Handling Slot Brackets

    Expansion cards For system relevant information, see the hardware configurator of your server available online at the following address:https://ts.fujitsu.com/ products/standard_servers/index.htm For Japan: https://www.fujitsu.com/jp/products/computing/servers/primergy/ Handling slot brackets 9.3.1 Installing slot brackets Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: Phillips PH2 / (+) No. 2 screw driver / hexagon screw driver 5 mm Use the low profile bracket perforated for relevant controllers.
  • Page 114 Expansion cards Figure 66: Perforated and non-perforated slot brackets Full height bracket non-perforated Low profile bracket perforated Full height bracket perforated Installing a slot bracket ▶ Place the controller on the mounting tabs on the slot bracket. ▶ Fasten the slot bracket to the controller with two screws. Upgrade and Maintenance Manual TX1310 M5...
  • Page 115 Expansion cards Example network adapter Figure 67: Placing the slot bracket ▶ Place the controller on the slot bracket (1). ▶ Carefully shift the slot bracket towards the controller (2). ▶ Ensure that the ESD springs properly engage with the slot bracket as shown (see circles).

  • Page 116: Removing Slot Brackets

    Expansion cards 9.3.2 Removing slot brackets Upgrade and Repair Unit Hardware: 5 minutes (URU) – Phillips PH2 / (+) No. 2 screw driver Tools: – Hexagon screw driver (for hexagon bolt) Removing a slot bracket ▶ Remove the two screws. ▶...
  • Page 117 Expansion cards Removing the slot cover Figure 69: Removing the slot cover ▶ Open the slot cover clamp (1). ▶ Remove the desired slot cover (2). CAUTION ▶ Keep the slot cover for future use. ▶ If the expansion card is removed and not replaced with a new one, the slot cover must be reinstalled due to cooling, to comply with applicable EMC regulations and to protect against fire.
  • Page 118 Expansion cards Installing an expansion card ▶ Remove the expansion card from its protective packaging. For further instructions regarding controller settings, please refer to the accompanying documentation. ▶ If applicable, attach the required slot bracket to the expansion card, see "Installing a slot bracket"...

  • Page 119: Removing An Expansion Card

    Expansion cards ▶ "Connecting the power cord" on page ▶ "Switching on the server" on page ▶ "Installing the bay cover" on page ▶ "Locking the server" on page ▶ "Resuming BitLocker functionality" on page ▶ If applicable, "After replacing or upgrading LAN controllers" on page Removing an expansion card Upgrade and Repair Unit Hardware: 5 minutes...
  • Page 120 Expansion cards Figure 71: Removing an expansion card ▶ Open the slot cover clamp (1). ▶ Carefully remove the expansion card from its slot (2). Installing the slot cover CAUTION ▶ Keep the slot cover for future use. ▶ If the expansion card is removed and not replaced with a new one, the slot cover must be reinstalled due to cooling, to comply with applicable EMC regulations and to protect against fire.
  • Page 121 Expansion cards Figure 72: Installing a slot cover ▶ Insert a slot cover into the unused PCI slot opening (1). ▶ Close the slot cover clamp (2). Concluding steps ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶...

  • Page 122: Replacing An Expansion Card

    Expansion cards Replacing an expansion card Upgrade and Repair Unit Hardware: 5 minutes (URU) Software: 5 minutes Tools: Only for installing or removing slot brackets: – Phillips PH2 / (+) No. 2 screw driver – Hexagon screw driver (for hexagon bolt) Note on network settings recovery When replacing network controllers or the system board, network configuration settings in the operating system will be lost and replaced...
  • Page 123 Expansion cards Installing the new expansion card ▶ If applicable, install the slot bracket, see "Installing a slot bracket" on page 114. ▶ Install the new expansion card, see "Installing an expansion card" on page 118. Concluding steps ▶ "Reassembling" on page 50 ▶...
  • Page 124 Expansion cards Upgrade and Maintenance Manual TX1310 M5...

  • Page 125: Main Memory

    Main memory 10.1 Safety notes CAUTION ▶ Before removing several memory modules, make sure that all memory modules can be reinstalled into their original slots. Otherwise, data may be lost. ▶ Do not install unsupported third party memory modules. For more information on supported memory modules, see "Basic informations"...

  • Page 126: Basic Informations

    Main memory 10.2 Basic informations F a n 2 ( S Y S ) P W R P W R 1 P W R 2 B T N C h a n n e l B , S l o t 1 ( D I M M - 1 B ) C h a n n e l B , S l o t 2 ( D I M M - 2 B ) S E R I A L C h a n n e l A , S l o t 1 ( D I M M - 1 A )
  • Page 127 Main memory – Within both channels, memory slot 1 (i. e. the black slot) must be populated prior to slot 2 (blue slot). – For maximum performance, populate both channels with the same amount of memory (symmetric dual channel configuration). Channel A Channel B Memory slot...

  • Page 128: Installing Memory Modules

    Main memory 10.3 Installing memory modules Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less Preliminary steps ▶ "Suspending BitLocker functionality" on page ▶ "Unlocking the server" on page ▶ "Removing the bay cover" on page ▶ "Shutting down the server" on page ▶...

  • Page 129: Removing Memory Modules

    Main memory Figure 75: Installing a memory module ▶ Align the notch on the bottom of the module with the crossbar in the slot. ▶ Press down on the memory module until the securing clips snap into the cutouts at each end of the module. Concluding steps ▶...
  • Page 130 Main memory CAUTION ▶ Use only released configurations to ensure a faultless operation of the system. ▶ Before changing the memory configuration, verify if the configuration is released. Please contact your sales outlet or our customer service center. Preliminary steps ▶...

  • Page 131: Replacing Memory Modules

    Main memory ▶ Remove the ejected memory module. ▶ Close the securing clips. CAUTION If the clips are open, they can collide with a cable clamp. Concluding steps ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶ "Switching on the server"...
  • Page 132 Main memory Removing the defective memory module ▶ Remove the memory module, see "Removing a memory module" on page 130. Installing the new memory module ▶ Install the memory module, see "Installing a memory module" on page 128. Concluding steps ▶...

  • Page 133: Processor (Cpu)

    Processor (CPU) 11.1 Safety notes CAUTION ▶ Do not install unsupported CPUs. For more information on supported CPUs, see "Basic information" on page 134. ▶ Circuit boards and soldered parts of internal options are exposed and can be damaged by static electricity. Always discharge static build-up (e.g.

  • Page 134: Basic Information

    L E D Figure 78: Position CPU socket The system board supports one CPU socket. For system relevant information, see the hardware configurator of your server available online at the following address: https://ts.fujitsu.com/products/standard_servers/index.htm For Japan: https://www.fujitsu.com/jp/products/computing/servers/primergy/ Upgrade and Maintenance Manual TX1310 M5...

  • Page 135: Upgrading Or Replacing The Cpu

    Processor (CPU) 11.3 Upgrading or replacing the CPU Field Replaceable Unit Hardware: 15 minutes (FRU) Software: 5 minutes Tools: Phillips PH2 / (+) No. 2 screw driver CAUTION CPUs are extremely sensitive to electrostatic discharge and therefore must always be handled with care. ▶...
  • Page 136 Processor (CPU) Removing the heat sink Figure 79: Removing the heat sink (A) ▶ Disconnect the CPU fan cable from system board connector "Fan (CPU)" Figure 80: Removing the heat sink (B) ▶ Loosen the four captive screws on the heat sink in a crossover pattern (1-4). Upgrade and Maintenance Manual TX1310 M5...
  • Page 137 Processor (CPU) Figure 81: Removing the heat sink (C) ▶ Carefully turn the heat sink left and right to detach it from the CPU (1). This may be necessary due to the adhesive quality of the thermal paste located between the heat sink and CPU. CAUTION ▶...
  • Page 138 Processor (CPU) Removing the CPU Figure 82: Opening socket release lever ▶ Unlatch the socket release lever by pushing it down and away from the socket (1). ▶ Fold back the socket release lever (2). Upgrade and Maintenance Manual TX1310 M5...
  • Page 139 Processor (CPU) Figure 83: Opening the load plate ▶ Rotate the socket lever to lift the load plate away from the socket. ▶ Make sure that the load plate is in the fully open position. TX1310 M5 Upgrade and Maintenance Manual...
  • Page 140 Processor (CPU) Figure 84: Removing the CPU ▶ Carefully remove the CPU from its socket in a vertical motion. CAUTION ▶ Be careful not to touch or bend the spring contacts on the CPU socket. Installing the CPU ▶ Confirm that the CPU model number printed on the top of the CPU fits with the requirements.
  • Page 141 Processor (CPU) Figure 85: Installing the CPU ▶ Hold the CPU with your thumb and index finger. ▶ Make sure that the notches on the CPU align with the posts on the socket (see close-up). ▶ Lower the CPU straight down without tilting or sliding it in the socket. CAUTION ▶...
  • Page 142 Processor (CPU) Figure 86: Closing the load plate (A) ▶ Lower the load plate over the CPU while leaving the socket lever in its open position. Upgrade and Maintenance Manual TX1310 M5...
  • Page 143 Processor (CPU) Figure 87: Closing the load plate (B) ▶ Lower the socket lever while making sure that the front edge of the load plate slides under the shoulder screw cap (see close-up) as the lever is lowered. Figure 88: Closing the socket release lever TX1310 M5 Upgrade and Maintenance Manual...
  • Page 144 Processor (CPU) ▶ Latch the socket lever under the load plate tab. Applying thermal paste to the CPU surface For Japan, the service engineer must follow the instruction provided separately. If the CPU upgrade or replacement kit contains a new heat sink, a thin layer of thermal compound has already been pre-applied to its lower surface.
  • Page 145 Processor (CPU) Add graduation marks to the syringe using a permanent marker to help you apply the thermal paste. Figure 90: Applying the thermal paste ▶ Apply a small point-shaped amount of thermal paste (1.0 gram, see description above) to the center of the CPU surface as shown. CAUTION ▶...
  • Page 146 Processor (CPU) Installing the heat sink Figure 91: Installing the heat sink (A) ▶ Carefully seat the heat sink on the four threaded holes as shown (1). ▶ Ensure that the screws on the heat sink are properly seated on the threaded holes (see circles).
  • Page 147 Processor (CPU) Figure 92: Installing the heat sink (B) ▶ Fasten the four captive screws on the heat sink in a crossover pattern (screw torque: 0.6 Nm, not applicable for Japan) (1-4). Figure 93: Installing the heat sink (C) ▶ Connect the CPU fan cable to system board connector "Fan (CPU)". TX1310 M5 Upgrade and Maintenance Manual...

  • Page 148: Replacing The Heat Sink

    Processor (CPU) Concluding steps ▶ "Installing the top HDD cage" on page ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶ "Switching on the server" on page When the system is powered on after a CPU has been replaced or upgraded, the Global Error indicator will start flashing with the message CPU has been changed.
  • Page 149 Processor (CPU) Tools: Phillips PH2 / (+) No. 2 screw driver The CPU fan is implemented in the heat sink. When the CPU fan is defective, the heat sink must be replaced. Preliminary steps ▶ "Unlocking the server" on page ▶...

  • Page 150: Handling The Protectice Cover

    Processor (CPU) ▶ "Locking the server" on page 11.5 Handling the protectice cover Installing the protective cover Figure 94: Attaching the protective socket cover ▶ Carefully lower the protective socket cover onto the CPU socket in a vertical motion until it snaps in place. Upgrade and Maintenance Manual TX1310 M5...
  • Page 151 Processor (CPU) Figure 95: Closing the load plate (A) ▶ Lower the load plate over the CPU cover while leaving the socket lever in its open position. TX1310 M5 Upgrade and Maintenance Manual...
  • Page 152 Processor (CPU) Figure 96: Closing the load plate (B) ▶ Lower the socket lever while making sure that the front edge of the load plate slides under the shoulder screw cap (see close-up) as the lever is lowered. Figure 97: Latching the socket lever Upgrade and Maintenance Manual TX1310 M5...
  • Page 153 Processor (CPU) ▶ Latch the socket lever under the load plate tab. Removing the protective cover Figure 98: Opening socket release lever ▶ Unlatch the socket release lever by pushing it down and away from the socket (1). ▶ Fold back the socket release lever (2). TX1310 M5 Upgrade and Maintenance Manual...
  • Page 154 Processor (CPU) Figure 99: Opening the load plate ▶ Press down on the socket lever to lift the load plate away from the socket. ▶ Fully open the load plate. Upgrade and Maintenance Manual TX1310 M5...
  • Page 155 Processor (CPU) Figure 100: Removing the protective cover ▶ Remove the protective cover from the CPU socket. Proceed as follows: ▶ Place your thumb against the front edge of the protective socket cover and rest your index finger on the rear grip. ▶...
  • Page 156 Processor (CPU) Upgrade and Maintenance Manual TX1310 M5...

  • Page 157: Accessible Drives

    Accessible drives 12.1 Safety notes CAUTION ▶ Before installing an accessible drive, acquaint yourself with the drive's user documentation. ▶ When inserting an accessible drive into the server, ensure not to pinch or strain any connected cables. ▶ When installing an accessible drive, hold it by its sides. Applying force to the top of the casing may cause failures.

  • Page 158: Optical Disk Drive (Odd)

    Accessible drives Figure 101: Accessible drive bays Sequence Accessible drive Bay Max. number Slimline ODD RDX backup drive 2 Table 4: Accessible drive mounting sequence 12.3 Optical disk drive (ODD) 12.3.1 Installing the ODD Upgrade and Repair Unit Hardware: 10 minutes (URU) Tools: Thin slotted screw driver (for removing the bracket wall)
  • Page 159 Accessible drives ▶ "Removing the bay cover" on page ▶ "Shutting down the server" on page ▶ "Disconnecting the power cord" on page ▶ "Getting access to the component" on page Removing the bracket wall bay 1 CAUTION ▶ You cannot install the bracket wall again. ▶...
  • Page 160 Accessible drives Preparing the ODD There are two fixation plates for accessible drives. You need one fixation plate for every accessible drive to be installed. Figure 103: Removing the fixation plate from the chassis ▶ Unclip the fixation plate (see arrow). Figure 104: Attaching the fixation plate to the ODD ▶...
  • Page 161 Accessible drives Installing the ODD Figure 105: Installing the ODD ▶ While pressing the fixation plate against the ODD, insert the ODD into accessible drive bay 1 and push until it is firmly seated in its connector on the ODD back plate. Since the ODD is connected to the ODD back plate, no further cable connection is necessary.

  • Page 162: Removing The Odd

    Accessible drives 12.3.2 Removing the ODD Upgrade and Repair Unit Hardware: 10 minutes (URU) Tools: tool-less CAUTION ▶ Always replace drives to comply with applicable EMC regulations and satisfy cooling requirements. Preliminary steps ▶ "Suspending BitLocker functionality" on page ▶ "Removing backup and optical disk media"...
  • Page 163 Accessible drives Removing the ODD Figure 106: Removing the ODD ▶ To disengage the ODD, press down on the latch marked "1" (1) while pulling the locking handle in the drive cage to the left (2). ▶ Remove the ODD out of its bay (3). Concluding steps ▶...

  • Page 164: Replacing The Odd

    Accessible drives 12.3.3 Replacing the ODD Upgrade and Repair Unit Hardware: 15 minutes (URU) Tools: tool-less Preliminary steps ▶ "Suspending BitLocker functionality" on page ▶ "Removing backup and optical disk media" on page ▶ "Verifying and configuring the backup software solution" on page ▶...

  • Page 165: Rdx Drive

    Accessible drives ▶ Align the two pins on the fixation plate with the screw holes in the ODD. ▶ Attach the fixation plate to the left side of the new ODD. ▶ Install the new ODD, see "Installing the ODD" on page 158.
  • Page 166 Accessible drives ▶ "Disconnecting the power cord" on page ▶ "Getting access to the component" on page ▶ "Removing the top HDD cage" on page Removing the bracket wall bay 2 If bay 2 is to be equipped, it is necessary to remove its front bracket wall. CAUTION ▶...
  • Page 167 Accessible drives Preparing the RDX backup drive There are two fixation plates for accessible backup drives. You need one fixation plate for every accessible backup drive to be installed. Figure 109: Removing the fixation plate from the chassis ▶ Unclip the fixation plate (see arrow). Figure 110: Attaching the fixation plate to the RDX backup drive ▶...
  • Page 168 Accessible drives Installing the RDX backup drive For easier access to the backup drive connectors, it is recommended to remove the PSU before installing the backup drive, see "Removing the PSU" on page Figure 111: Inserting RDX backup drive into bay 2 ▶...

  • Page 169: Removing The Rdx Backup Drive

    Accessible drives ▶ Push the RDX backup drive somewhat to the front side to get more space. ▶ Connect the power cable to the RDX backup drive (1). ▶ Connect the USB 3.0 cable to the RDX backup drive (2). ▶...
  • Page 170 Accessible drives ▶ "Unlocking the server" on page ▶ "Removing the bay cover" on page ▶ "Shutting down the server" on page ▶ "Disconnecting the power cord" on page ▶ "Getting access to the component" on page ▶ "Removing the top HDD cage" on page Removing the RDX backup drive For easier access to the backup drive connectors, it is recommended to remove the PSU before installing the RDX backup drive, see...

  • Page 171: Replacing The Rdx Backup Drive

    Accessible drives ▶ "Connecting the power cord" on page ▶ "Switching on the server" on page ▶ "Installing the bay cover" on page ▶ "Locking the server" on page ▶ "Reconfiguring the backup software solution" on page ▶ "Resuming BitLocker functionality" on page 12.4.3 Replacing the RDX backup drive Upgrade and Repair Unit...
  • Page 172 Accessible drives Installing the new RDX backup drive ▶ Align the four pins on the fixation plate with the screw holes in the new RDX backup drive. Figure 114: Attaching the fixation plate to the RDX backup drive ▶ Attach the fixation plate on the left side of the new RDX backup drive. ▶...

  • Page 173: Front Panel And Front Usb

    Front panel and front USB Front connectors and indicators are integral parts of the system board. There is no individual front panel module. In case of defective front connectors or indicators, the system board needs to be replaced. Proceed as described in "Replacing the system board"...
  • Page 174 Front panel and front USB Upgrade and Maintenance Manual TX1310 M5...

  • Page 175: Serial Interface

    Serial interface 14.1 Safety notes CAUTION ▶ For more information, see "Important information" on page 14.2 Installing the serial interface Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: ● Thin slotted screw driver (for removing the metal cover) ● Hexagon screw driver 5 mm Preliminary steps ▶...
  • Page 176 Serial interface Breaking off the metal cover Figure 115: Removing the metal cover ▶ Insert the flat screw driver into the slot and twist to break off the metal cover (see close-up). Installing the serial interface Figure 116: Installing the serial interface (A) Upgrade and Maintenance Manual TX1310 M5...

  • Page 177: Removing The Serial Interface

    Serial interface ▶ Insert the serial interface into the slot (1). ▶ Connect the cable to the system board "SERIAL" (2). Figure 117: Installing the serial interface (B) ▶ Fasten the serial interface with two hexagon bolts (see circles). Concluding steps ▶...
  • Page 178 Serial interface Tools: Hexagon screw driver 5 mm Preliminary steps ▶ "Unlocking the server" on page ▶ "Removing the bay cover" on page ▶ "Shutting down the server" on page ▶ "Disconnecting the power cord" on page ▶ "Getting access to the component" on page Removing the serial interface Figure 118: Removing the serial interface (A) ▶...

  • Page 179: Replacing The Serial Interface

    Serial interface Figure 119: Removing the serial interface (B) ▶ Remove the serial interface (1). ▶ Remove the cable from the system board (2). Concluding steps ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶ "Switching on the server" on page ▶...
  • Page 180 Serial interface Preliminary steps ▶ "Unlocking the server" on page ▶ "Removing the bay cover" on page ▶ "Shutting down the server" on page ▶ "Disconnecting the power cord" on page ▶ "Getting access to the component" on page Removing the defective serial interface ▶...

  • Page 181: System Board And Components

    System board and components 15.1 Safety notes CAUTION ▶ Devices and components inside the server remain hot after shutdown. After shutting down the server, wait for hot components to cool down before installing or removing internal options. ▶ Circuit boards and soldered parts of internal options are exposed and can be damaged by static electricity.

  • Page 182: Cmos Battery

    System board and components 15.3 CMOS battery 15.3.1 Replacing the CMOS battery Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less; recommended: tooth pick CAUTION ▶ The CMOS battery must be replaced with an identical battery or with a battery type recommended by the manufacturer. ▶...
  • Page 183 System board and components Replacing the defective CMOS battery Figure 120: Replacing the CMOS battery ▶ Press the locking spring into direction of the arrow (1), so that the CMOS battery jumps out of its socket. ▶ Remove the CMOS battery (2). CAUTION Sharp tools such as screw drivers might damage system board components in case of slipping.

  • Page 184: Trusted Platform Module (Tpm)

    System board and components ▶ "Resuming BitLocker functionality" on page ▶ "Verifying the system time settings" on page ▶ If applicable, restore the BIOS settings manually. 15.4 Trusted Platform Module (TPM) 15.4.1 TPM kit There are different TPM kits available. The procedures of installing, removing and replacing are identic.

  • Page 185: Installing The Tpm

    System board and components The black TPM spacer is not used in this server. 15.4.2 Installing the TPM Field Replaceable Unit Hardware: 5 minutes (FRU) Software: 5 minutes Tools: – Bit screw driver – TPM bit insert For Japan: – TPM module fixing tool (S26361-F3552-L909) Preliminary steps ▶...
  • Page 186 System board and components Installing the TPM Figure 123: Installing the TPM spacer on the bottom system board ▶ Install the TPM spacer on the hole on the bottom system board. Figure 124: TPM bit insert ▶ Attach the TPM bit insert or TPM module fixing tool (for Japan) to a bit screw driver.
  • Page 187 System board and components Figure 125: Installing the TPM ▶ Connect the TPM to the system board (1). ▶ Fasten the TPM with the special screw for the TPM using the TPM bit insert or TPM module fixing tool (for Japan) (2). CAUTION ▶...

  • Page 188: Removing The Tpm

    System board and components Enabling the TPM in the system board BIOS Proceed as follows: ▶ Switch on or restart your server. ▶ As soon as the startup screen appears, press the [F2] function key to enter the BIOS setup menu. ▶...
  • Page 189 System board and components CAUTION ▶ Advise your contact persons that they must provide you with all recovery keys which belong to the system to restore them in the TPM later. Preliminary steps Preliminary steps are not necessary, if a system board has to be replaced and the TPM is used again.
  • Page 190 For more information on how to disable BitLocker drive encryption, see the Microsoft Knowledge Base. See the Fujitsu web pages for more details. Disabling the TPM in the system board BIOS Proceed as follows: ▶...
  • Page 191 System board and components Removing the TPM ▶ Remove the system board, see "Removing the defective system board" on page 208. ▶ Lay the system board on a soft, antistatic surface with its component side facing down. Figure 126: Removing the TPM screw ▶...

  • Page 192: Replacing The Tpm

    System board and components Figure 127: Removing the TPM spacer ▶ Using a flat nose pliers, press together the hooks on the TPM spacer (1, see close-up) and remove it from the system board (2). If the TPM is to be replaced, the TPM spacer may remain on the system board.
  • Page 193 System board and components Tools: Removing the system board: – Phillips PH2 / (+) No. 2 screw driver Replacing the TPM: – Bit screw driver – TPM bit insert – Flat nose pliers – Thin slotted screw driver (2 x 0.4 mm) For Japan: –...

  • Page 194: M.2 Ssd

    System board and components Removing the defective TPM ▶ Remove the TPM, see "Removing the TPM" on page 191. ▶ Leave the TPM spacer on the bottom system board when removing the defective TPM. Installing the new TPM The TPM spacer is already present on the system board. ▶...
  • Page 195 System board and components Figure 128: Example M.2 SSD Figure 129: Slots and bolts for M.2 SSDs M.2 slot 1 M.2 slot 2 TX1310 M5 Upgrade and Maintenance Manual...

  • Page 196: Installing An M.2 Ssd

    System board and components The second hole is for M.2 SSDs with 110 mm length (see orange circles). If necessary, move the M.2 lock to the second hole, see "Moving the M.2 lock to the second hole" on page 196. 15.5.2 Installing an M.2 SSD Upgrade and Repair Unit...
  • Page 197 System board and components Figure 130: Removing the M.2 lock (A) ▶ Open the M.2 lock. Figure 131: Removing the M.2 lock (B) ▶ Pull out the M.2 lock in direction of the arrow. TX1310 M5 Upgrade and Maintenance Manual...
  • Page 198 System board and components Figure 132: Inserting the M.2 lock ▶ Insert the M.2 lock in the second hole (see circle). The M.2 lock has a pin (A) to ensure right insertion. Installing the M.2 SSD CAUTION An M.2 SSD in M.2 slot 2 is not recognized, if M.2 slot 1 is free. ▶...
  • Page 199 System board and components Figure 133: Opening the M.2 lock ▶ Open the M.2 lock. Figure 134: Installing the M.2 SSD (A) ▶ With the label facing up, insert the M.2 SSD into the M.2 slot at a slight angle (1). ▶...
  • Page 200 System board and components Figure 135: Installing the M.2 SSD (B) ▶ Close the M.2 lock to fasten the M.2 SSD. Concluding steps ▶ If applicable, install an expansion card, see "Installing an expansion card" on page 118. ▶ Install the front fan, see "Installing the new front fan"...

  • Page 201: Removing An M.2 Ssd

    For Japan In order to setup the ESXi, see the corresponding version of the "VMware vSphere Software Description" from the following URL and reinstall ESXi to the M.2 SSD. https://jp.fujitsu.com/platform/server/primergy/software/vmware/manual/ 15.5.3 Removing an M.2 SSD Upgrade and Repair Unit Hardware: 5 minutes...
  • Page 202 System board and components Preliminary steps ▶ "Unlocking the server" on page ▶ "Removing the bay cover" on page ▶ "Shutting down the server" on page ▶ "Disconnecting the power cord" on page ▶ "Getting access to the component" on page ▶...
  • Page 203 System board and components Figure 137: Removing the M.2 SSD (B) ▶ Remove the M.2 SSD out of the M.2 lock (1). ▶ Remove the M.2 SSD out of the M.2 SSD slot in direction of the arrow (2). Figure 138: Closing the M.2 lock ▶...

  • Page 204: Replacing An M.2 Ssd

    System board and components Concluding steps ▶ If applicable, install an expansion card, see "Installing an expansion card" on page 118. ▶ Install the front fan, see "Installing the new front fan" on page 108. ▶ "Reassembling" on page ▶ "Connecting the power cord"...

  • Page 205: System Board

    System board and components Replacing the M.2 SSD ▶ Remove the defective M.2 SSD, see "Removing the M.2 SSD" on page 202. ▶ Install the new M.2 SSD, see "Installing the M.2 SSD" on page 198. Concluding steps ▶ If applicable, install an expansion card, see "Installing an expansion card"...
  • Page 206 System board and components Tools: Replacing the system board: – Phillips PH2 / (+) No. 2 screw driver – Magnifying glass for inspecting CPU socket springs (recommended) Replacing the TPM: – Bit screw driver – Flat nose pliers – TPM bit insert –...
  • Page 207 System board and components Note on network settings recovery When replacing network controllers or the system board, network configuration settings in the operating system will be lost and replaced by default values. This applies to all static IP address and LAN teaming configurations.
  • Page 208 System board and components ▶ Remove all expansion cards, see "Removing an expansion card" on page 119. Before removing the expansion cards, take a note on the installation slot number for each card. Ensure that you reinstall the card in the slot it was located before the replacement.
  • Page 209 System board and components Figure 140: Removing the system board tray ▶ Pull the system board tray out of the chassis. TX1310 M5 Upgrade and Maintenance Manual...
  • Page 210 System board and components Figure 141: System board screws ▶ Remove eight screws from the system board (see circles). ▶ Use both hands to carefully pull the plug shells out of the connector panel and remove the system board from its tray. CAUTION ▶...
  • Page 211 System board and components ▶ If applicable, remove the TPM, see "Removing the TPM" on page 191. Installing the new system board ▶ Check the settings on the new system board, see "Onboard settings" on page 235. ▶ Insert the system board by holding it at a slight angle. ▶...
  • Page 212 System board and components ▶ Fasten the remaining bolts of the system board with six screws (see blue circles). Figure 143: Installing the system board tray ▶ Carefully push the system board tray back. Figure 144: System board tray - Location of screws Upgrade and Maintenance Manual TX1310 M5...
  • Page 213 System board and components ▶ Fasten the system board tray to the chassis with five screws (see circles). ▶ Remove the protective cover from the CPU socket of the new system board, "Removing the protective cover" on page 153. ▶ Remove the CPU from the defective system board, see "Removing the CPU"...
  • Page 214 System board and components ▶ "Switching on the server" on page When the system is powered on after a CPU has been replaced or upgraded, the message "CPU has been changed" appears. This only indicates that the CPU configuration has been altered. There is no technical problem.
  • Page 215 System board and components ▶ If applicable, restore LAN teaming configurations, see "After replacing a system board" on page TX1310 M5 Upgrade and Maintenance Manual...
  • Page 216 System board and components Upgrade and Maintenance Manual TX1310 M5...

  • Page 217: Cables

    Cables 16.1 Safety notes CAUTION ▶ Always hold cables by their connectors when disconnecting them. Never pull on the cable to disconnect cables. ▶ Ensure that none of the cables are scraped, strained or otherwise damaged while replacing system components. ▶...
  • Page 218 Cables Preliminary steps ▶ "Unlocking the server" on page 39 ▶ "Removing the bay cover" on page 40 ▶ "Shutting down the server" on page 41 ▶ "Disconnecting the power cord" on page ▶ "Getting access to the component" on page Removing the defective system cable ▶...
  • Page 219 Cables Figure 146: Removing the connectors from top HDD cage ▶ Pinch the sides of the connector (1) and remove it from the top HDD cage (2). ▶ Disconnect all system cable connectors from the system board. ▶ Remove the defective cable. Installing the new system cable ▶...

  • Page 220: Replacing The Hdd Cable (Bottom Hdd Cage)

    Cables Concluding steps ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶ "Switching on the server" on page 57 ▶ "Installing the bay cover" on page 58 ▶ "Locking the server" on page 59 16.4 Replacing the HDD cable (bottom HDD cage) The following steps are only required in case of a defective cable.
  • Page 221 Cables Removing the defective HDD cable ▶ If applicable, remove HDD1 and HDD2, see "Removing a 3.5-inch HDD" on page ▶ Pull the system board tray out of the chassis, see "Removing the defective system board" on page 208. Figure 147: Removing the screws ▶...
  • Page 222 Cables Figure 148: Removing the HDD cage bottom ▶ Pull the bottom HDD cage to the front as far as possible, lift it over the cant and remove it. Figure 149: Removing the defective cable ▶ Pinch the sides of the connector (1) and remove it from the bottom HDD cage (2).
  • Page 223 Cables Figure 150: Removing the screw ▶ Remove the screw (see close-up). ▶ Remove the defective cable from the bottom HDD cage. Installing the new HDD cable When installing the bottom HDD cage into the chassis, make sure that the chassis is in upright position. ▶...
  • Page 224 Cables ▶ Push the bottom HDD cage back into the chassis until the fixation bolts lock in the narrow ends of the keyhole slots. ▶ Fasten the bottom HDD cage with two screws. ▶ If applicable, install HDD1 and HDD2, see "Installing a 3.5-inch HDD"...

  • Page 225: Mechanical Overview

    Appendix A 17.1 Mechanical overview 17.1.1 Server front Figure 152: Server front with bay cover (left) and without bay cover (right) Ultra slim ODD (optional) Front USB connectors (2x) RDX backup drive (optional) Key lock On/Off button TX1310 M5 Upgrade and Maintenance Manual...

  • Page 226: Server Rear

    Appendix A 17.1.2 Server rear Figure 153: Server rear Standard PSU USB 3.2 Gen2x1 (10 Gbps) connectors Serial interface (optional) (2x) Video connector (Display port) Optional expansion cards (4x) USB 2.0 connectors (4x) LAN connectors (2x) Upgrade and Maintenance Manual TX1310 M5...

  • Page 227: Server Interior

    Appendix A 17.1.3 Server interior Figure 154: Server interior HDD 2 Memory modules TPM board (if installed) HDD 1 Fan2 SYS Fan1 SYS CPU / CPU heat sink / CPU fan HDD 4 System board HDD 3 Expansion card slots Accessible drive bays TX1310 M5 Upgrade and Maintenance Manual...

  • Page 228: Connectors And Indicators

    Appendix A 17.2 Connectors and indicators 17.2.1 Connectors on the system board Figure 155: Internal connectors on the system board D3930 Pos. Print Description Fan2 (SYS) Rear fan connector PWR1 PSU Power Upgrade and Maintenance Manual TX1310 M5...
  • Page 229 Appendix A Pos. Print Description PWR2 Power connector USB 3.0 USB 3.0 connector USB 3.0 USB 3.0 connector USB 8 USB connector for backup drives Fan (CPU) CPU fan connector SATA ODD ODD connector for backup drives SATA 4 SATA 4 connector SATA 3 SATA 3 connector PWR4...

  • Page 230: Server Front

    Appendix A 17.2.2 Server front 17.2.2.1 Connectors on the server front Figure 156: Connectors on the server front USB 3.2 Gen2 (20 Gbps) Type C USB 3.2 Gen1 (5 Gbps) connector (1x) connector (5V/3A) (1x) Some of the devices that can be connected may require special drivers (see the documentation for the connected device).

  • Page 231: Indicators On The Drives

    Appendix A Status Description green on The server is switched on. HDD/SSD activity indicator (2) Status Description green flashing Data access in progress. 17.2.2.3 Indicators on the drives Figure 158: Indicators on the drives ODD activity indicator RDX drive Power-on indicator ODD activity indicator (1) ODDs may have an indicator or not.
  • Page 232 Appendix A Status Description The ODD is inactive. green on The storage medium is being accessed. RDX drive Power-on indicator (2) Status Description The drive is not powered on. green on The drive is ready and working properly. green flashing The drive is ejecting media.

  • Page 233: Server Rear

    Appendix A 17.2.3 Server rear 17.2.3.1 Connectors on the I/O panel Figure 159: Connectors on the I/O panel LAN connectors (2x) Video connector (Display Port) USB 3.2 connectors (2x) Serial interface (optional) USB 2.0 connectors (4x) Some of the devices that can be connected may require special drivers (see the documentation for the connected device).

  • Page 234: Indicators On The I/O Panel

    Appendix A 17.2.3.2 Indicators on the I/O panel Figure 160: Indicators on the I/O panel LAN link/ transfer indicator LAN speed indicator LAN link/ transfer indicator (1) Status Description green on A LAN connection has been established. green flashing LAN data transfer is in progress. LAN is not connected.

  • Page 235: Onboard Settings

    Appendix A 17.3 Onboard settings Figure 161: Jumper Figure 162: Jumper settings of system board D 3930 TX1310 M5 Upgrade and Maintenance Manual...

  • Page 236: Minimum Startup Configuration

    Appendix A 17.4 Minimum startup configuration Field Replaceable Units (FRU) If the server does not start up or other problems occur, it may be necessary to take the system down to its most basic configuration in order to isolate the defective component.
  • Page 237 Appendix A CAUTION ▶ Since the fan module is not included in the minimum startup configuration, the server must be shut down immediately after the diagnostic process is complete (POST phase has been passed). ▶ The minimum startup configuration must be used exclusively for diagnostic purposes by maintenance personnel, never in daily operation! TX1310 M5...
  • Page 238 Appendix A Upgrade and Maintenance Manual TX1310 M5...

  • Page 239: Supplied Documents

    The following documents are available in this appendix: ● "Cable plan for FUJITSU Server PRIMERGY TX1310 M5 Reference Manual" ● "List of Released Adapters incl. Installation sequence and priority" ● "Screw list for FUJITSU Server PRIMERGY TX1310 M5 Reference Manual" TX1310 M5 Upgrade and Maintenance Manual...
  • Page 240 Reference Manual - English Cable plan for FUJITSU Server PRIMERGY TX1310 M5 Reference Manual March 2022...
  • Page 241 Cable plan Contents Frontpage Contents List of used cables SysBoardConn CablingBasicPSU CablingFAN DATA HDD w/o BMC PWR HDD w/o BMC DATA HDD w/BMC PWR HDD w/BMC FRONT IO USB w/BMC DATA CP500i w/o BMC DATA CP500i w/BMC DATA CP2100 w/o BMC DATA CP2100 w/BMC DATA COM port TX1310 M5...

  • Page 242: List Of Used Cables

    Cable plan List of used cables Fujitsu PN Naming Part of Opt. CA05973-7063 TX M5 HDD LED CABLE, 1 to 1 DATA CP500i w/o BMC DATA CP500i w/BMC Opt. CA05973-7065 TX M5 RS-232 CABLE DATA COM port Opt. CA05973-7066 RDX USB CABLE...

  • Page 243: Sysboardconn

    Cable plan SysBoardConn System Board System Board System Board (Without BMC) (With BMC) (With BMC) D3930 D3931 D3931 PWR 1 PWR 1 PWR 1 PWR 2 PWR 4 PWR 4 PWR 4 SATA 0-3 SATA 0-3 SATA 1 SATA ODD SATA ODD SATA 2 USB 8...

  • Page 244: Cablingbasicpsu

    Cable plan CablingBasicPSU Power Supply Power Supply Power Supply Power Supply 250W 250W 250W 250W E591-V70-1 E591-V70-1 E591-V70-2 E591-V70-2 System Board System Board (Without BMC) (With BMC) D3930 D3931 PWR 1 PWR 1 TX1310 M5...

  • Page 245: Cablingfan

    Cable plan CablingFAN System Board D3930/D3931 CPU FAN CPU FAN CPU FAN CPU FAN FAN CPU Front FAN Front FAN FAN1 SYS Front FAN Front FAN FAN2 SYS Rear FAN Rear FAN Rear FAN Rear FAN TX1310 M5...

  • Page 246: Data Hdd W/O Bmc

    Cable plan DATA HDD w/o BMC System Board SATA SATA (Without BMC) HDD1 HDD1 D3930 SATA SATA SATA 1 SATA SATA SATA 2 HDD2 HDD2 CA05973-7070 SATA SATA SATA SATA SATA 3 HDD3 HDD3 SATA SATA SATA 4 CA05973-7071 SATA ODD SATA SATA HDD4...

  • Page 247: Pwr Hdd W/O Bmc

    Cable plan PWR HDD w/o BMC System Board (Without BMC) SATA SATA D3930 HDD1 HDD1 SATA SATA CA05973-7070 PWR 4 SATA SATA HDD2 HDD2 SATA SATA CA05973-7071 PWR 2 SATA SATA HDD3 HDD3 SATA SATA SATA SATA HDD4 HDD4 SATA SATA Ultra Ultra...

  • Page 248: Data Hdd W/Bmc

    Cable plan DATA HDD w/BMC System Board (With BMC) D3931 SATA SATA HDD1 HDD1 CA05973-7069 SATA SATA SATA 0-3 SATA ODD SATA SATA USB 8 HDD2 HDD2 SATA SATA SATA SATA HDD3 HDD3 SATA SATA SATA SATA HDD4 HDD4 SATA SATA Ultra Ultra...

  • Page 249: Pwr Hdd W/Bmc

    Cable plan PWR HDD w/BMC System Board System Board SATA SATA (With BMC) (With BMC) HDD1 HDD1 D3931 D3931 SATA SATA SATA SATA CA05973-7069 HDD2 HDD2 SATA SATA SATA SATA HDD3 HDD3 SATA SATA SATA SATA HDD4 HDD4 SATA SATA Ultra Ultra Slim...

  • Page 250: Front Io Usb W/Bmc

    Cable plan FRONT IO USB w/BMC System Board System Board (With BMC) (With BMC) FRONT IO USB FRONT IO USB D3931 D3931 Cable Cable CA05973-7068 TYPE A FRONT TYPE A FRONT TYPE A TYPE A TYPE C FRONT TYPE C FRONT TYPE C TX1310 M5...

  • Page 251: Data Cp500I W/O Bmc

    Cable plan DATA CP500i w/o BMC System Board System Board (Without BMC) (Without BMC) SATA SATA D3930 D3930 HDD1 HDD1 SATA SATA CP500i CP500i CA05973-7070 RAID Card RAID Card SATA SATA Slot 4 (boot) Slot 4 (boot) HDD2 HDD2 SATA SATA CA05973-8102 SATA...

  • Page 252: Data Cp500I W/Bmc

    Cable plan DATA CP500i w/BMC System Board System Board (With BMC) (With BMC) SATA SATA D3931 D3931 HDD1 HDD1 SATA SATA CP500i CP500i RAID Card RAID Card Slot 3 (boot) Slot 3 (boot) SATA SATA HDD2 HDD2 CA05973-7069 SATA SATA SATA SATA HDD3...

  • Page 253: Data Cp2100 W/O Bmc

    Cable plan DATA CP2100 w/o BMC System Board System Board (Without BMC) (Without BMC) SATA SATA D3930 D3930 HDD1 HDD1 SATA SATA CP2100-8i CP2100-8i RAID Card RAID Card CA05973-7070 Slot 4 (boot) Slot 4 (boot) SATA SATA HDD2 HDD2 SATA SATA CA05973-8102 SATA...

  • Page 254: Data Cp2100 W/Bmc

    Cable plan DATA CP2100 w/BMC System Board System Board (With BMC) (With BMC) SATA SATA D3931 D3931 HDD1 HDD1 SATA SATA CP2100-8i CP2100-8i RAID Card RAID Card Slot 3 (boot) Slot 3 (boot) SATA SATA HDD2 HDD2 CA05973-7069 SATA SATA SATA SATA HDD3...

  • Page 255: Data Com Port

    Cable plan DATA COM port System Board System Board D3930/ D3931 D3930/ D3931 COM Port COM Port Cable Cable CA05973-7065 SERIAL SERIAL COM Port COM Port TX1310 M5...
  • Page 256 System Name: PRIMERGY TX1310 M5 CPU sockets #PCIe Slots of system Riser Option support (y/n) Overview and properties of System PCI devices and slots List of Released Adapters incl. Installation sequence and priority System PCI Slot # 1(D3930) 2 (D3930)
  • Page 257 List of all used screws for PRIMERGY Servers Assembled in WCZ and FIT July 2021...
  • Page 258 Torx 6 Plus black 0.09 Nm C26192-Y10-C103 Phillips PH1 Replacement S204 M2.5 x 4 mm silver 0.4 Nm screw for / JIS 1012 type A3C40137316 / LSZ: L3-25419-01 S205 Phillips PH1 silver 0.3 Nm M2.5 x 6.5mm Copyright 2021 FUJITSU LIMITED...
  • Page 259 A3C40109082 M3 x 4 mm Phillips PH1 white 0.09 Nm countersink M3 x 4 mm S304 A3C40142649 silver 0.4 Nm countersink Phillips PH1 Screws in kit: S26361-D3305- Phillips PH1 S305 M3 x 4 mm silver 0.4Nm Copyright 2021 FUJITSU LIMITED...
  • Page 260 “self-tapping” S311 C26361-B443- M3 x 3.2 mm Lens head screw silver 0.2 Nm C220 cross PZ2 S312 M3 x 6.7 mm Phillips PH2 silver 0.6 Nm S313 M3 Fastener Phillips PH2 Screw silver 0.6 Nm Copyright 2021 FUJITSU LIMITED...
  • Page 261 M3 x 4 mm Phillips PH2 silver 0.6 Nm S319 M3 x 4.5 mm Phillips PH2 0.6 ~ 0.7 silver S320 M3 x 5 mm Phillips PH2 silver 0.7 Nm S321 M3 Captive Phillips PH2 Screw silver 0.6 Nm Copyright 2021 FUJITSU LIMITED...
  • Page 262 M3 x 5 mm Phillips PH2 silver 0.6 Nm S330 M3 x 5 mm Phillips PH2 black 0.6 Nm S331 M3 x 8 mm Phillips PH2 Silver 0.6 Nm S401 M4 x 6.5 mm Phillips PH2 silver 0.6 Nm Copyright 2021 FUJITSU LIMITED...
  • Page 263 M3 x 15 mm S508 M5 x 11 mm Phillips PH2 black 0.6 Nm UNC standoff EOL: V26827-B408- hexagon screw 4-40 x 7.8 mm V989 S601 silver 0.6 Nm driver 5 mm bolt: 4.9 mm V26827-B265-V5 total: 12.7 mm Copyright 2021 FUJITSU LIMITED...
  • Page 264 5 mm / silver 0.6 Nm provided by screw with cross PZ2 chassis spacer. vendor) (screw is C26361-Y10-C133 M2 x 3.5 mm Flat head Phillips silver 0.2 Nm part of PH 0 PDUAL AP200 kit) Copyright 2021 FUJITSU LIMITED...
  • Page 265 S319 Torque 0.6 ~ 0.7 Nm 07. June 2021 Update CP100 screw driver as See yellow color update 24. June 2021 Add RX1330M5 screws See yellow color update 7. July 2021 Add TX1310M5 screws See yellow color update Copyright 2021 FUJITSU LIMITED...

Table of Contents