ADEMCO Lynx Installation Instructions Manual page 16

* 35
* 36
* 37
* 38
* 39
DIALER PROGRAMMING (
Fields * 40,
Enter 0–9, # + 11 for '
* 40
* 41
* 42
For Fields * 43 and * 44:
Enter [ * ] as the fourth digit if a 3-digit account number (for 3+1 dialer reporting format) is used. Enter 0 as the first digit of a 4-
digit account number for Nos. 0000–0999. Exit field by pressing [ * ] (and press next field number) if only 3 digits are used.
To clear entries from field, press * 43 * or * 44 * .
See blank Programming Form for examples of account number entries.
If using the paging feature, do not enter a leading 0 in the subscriber account number, and do not use digits A-F anywhere in the
number. Some paging systems provide voice mail capability, which is activated by a leading 0 in the message.
* 43
* 44
* 47
Entry delay 01
00-99 = entry delay time in seconds.
Entry delay 02
00-99 = entry delay time in seconds.
Audible exit warning/quick exit
Exit Warning Quick Exit
0 = no exit warning sound 0 = no quick exit
1 = provide exit warning 1 = allow quick exit
sound when armed AWAY
Confirmation of arming ding
0 = no ding
1 = confirmation ding after arming system
2 = confirmation ding after arming from RF
button or RF keypad only
Power up in previous state
0 = always power up in a disarmed state
1 = assume the system status prior to power-
down
40– 50)
* *
* 41, * 42: Enter up to the number of digits shown. Do not fill unused spaces.
' ; # + 12 for '#'; # + 13 for a pause (2 seconds)
*
PABX access code
Enter up to 6 digits if PABX is needed to access
an outside line.
Primary phone no.
Enter up to 20 digits.
Enter 0–9; # + 11 for ' * ' ; # + 12 for '#'; # + 13 for
a pause (2 seconds)
Secondary phone no.
Enter up to 24 digits.
Enter 0–9, # + 11 for ' * ' ; # + 12 for '#'; # + 13 for
a pause (2 seconds)
Primary subs account no.
Enter digits 0–9; # +11=B; # +12=C; # +13=D; #
+14=E; or # +15=F.
Secondary subs account no.
Enter digits 0–9; # +11=B; # +12=C; # +13=D; #
+14=E; or # +15=F.
Phone system select
If central station receiver is not on WATS line: 0
= Pulse Dial; 1 = Tone Dial
If central station receiver is on WATS line: 2 =
Pulse Dial; 3 = Tone Dial
The system will wait the time entered before sounding alarm upon
entering if system is not disarmed.
UL installations: must be set for a maximum of 20 seconds
The system will wait the time entered before sounding alarm upon
entering.
UL installations: must be set for a maximum of 20 seconds
Exit Warning: Sound consists of slow continuous beeps until last 5
seconds, when it changes to fast beeps. The warning sound will end at
the termination of exit delay.
Quick Exit: If enabled, user can restart the exit delay time after arming
in STAY mode by pressing the STAY key. This avoids having the user
disarm then re-arm the system after letting someone in or out.
Confirmation of arming is 1/2 second external sounder "ding" when
closing report is sent, or at the end of exit delay (ding occurs when the
system receives the RF transmission).
When the system powers up armed, an alarm will occur 1 minute after
arming if a zone is faulted.
Note that if the previous state was armed AWAY or STAY, the system
will not respond to sensor changes for 1 minute, which allows time for
sensors such as PIRs to stabilize.
UL installations: must be 1 (power up in previous state)
If fewer than 6 digits need to be entered, exit by pressing [*] and next
field number (e.g., 41). To clear entries from field, press *40*.
If fewer than 20 digits entered, exit by pressing [*] and next field
number (e.g., 42). To clear entries from field, press *41*.
Note: Backup reporting (8 attempts are made to the secondary phone
number if no kissoff is received after 8 attempts to the primary number)
is automatic only if there is a secondary phone number (field *42).
If fewer than 24 digits entered, exit by pressing [*] and next field
number (e.g., 43). To clear entries from field, press *42*. See backup
reporting note for field *41. If using the paging feature, enter the pager
phone number here.
Enter the primary subscriber account number.
To clear entries from field, press * 43 * .
Enter the secondary subscriber account number.
To clear entries from field, press * 44 * .
Enter the type of phone dialing: pulse or tone.
–16–