Mitsubishi Electric F700 Instruction Manual page 2

This Instruction Manual (Basic) provides handling information and precautions for use of the equipment.
Please forward this Instruction Manual (Basic) to the end user.
This section is specifically about safety matters
Do not attempt to install, operate, maintain or inspect the inverter
until you have read through this Instruction Manual (Basic) and
appended documents carefully and can use the equipment
correctly. Do not use the inverter until you have a full knowledge
of the equipment, safety information and instructions. In this
Instruction Manual (Basic), the safety instruction levels are
classified into "WARNING" and "CAUTION".
Incorrect handling may cause hazardous
WARNING
conditions, resulting in death or severe
injury.
Incorrect handling may cause hazardous
CAUTION
conditions, resulting in medium or slight
injury, or may cause only material damage.
The level may even lead to a serious consequence
CAUTION
according to conditions. Both instruction levels must be followed
because these are important to personal safety.
1. Electric Shock Prevention
WARNING
• While power is ON or when the inverter is running, do not open
the front cover. Otherwise you may get an electric shock.
• Do not run the inverter with the front cover or wiring cover
removed.
Otherwise you may access the exposed high-voltage terminals
or the charging part of the circuitry and get an electric shock.
• Even if power is off, do not remove the front cover except for
wiring or periodic inspection. You may access the charged
inverter circuits and get an electric shock.
• Before wiring, inspection or switching EMC filter ON/OFF
connector, power must be switched OFF. To confirm that, LED
indication of the operation panel must be checked. (It must be
OFF.) Any person who is involved in wiring, inspection or
switching EMC filter ON/OFF connector shall wait for at least
10 minutes after the power supply has been switched OFF and
check that there are no residual voltage using a tester or the
like. The capacitor is charged with high voltage for some time
after power OFF, and it is dangerous.
• This inverter must be earthed (grounded). Earthing (grounding)
must conform to the requirements of national and local safety
regulations and electrical code (NEC section 250, IEC 536
class 1 and other applicable standards).
A neutral-point earthed (grounded) power supply for 400V
class inverter in compliance with EN standard must be used.
• Any person who is involved in wiring or inspection of this
equipment shall be fully competent to do the work.
• The inverter must be installed before wiring. Otherwise you
may get an electric shock or be injured.
• Setting dial and key operations must be performed with dry
hands to prevent an electric shock. Otherwise you may get an
electric shock.
• Do not subject the cables to scratches, excessive stress,
heavy loads or pinching. Otherwise you may get an electric
shock.
• Do not replace the cooling fan while power is on. It is
dangerous to replace the cooling fan while power is on.
• Do not touch the printed circuit board with wet hands. You may
get an electric shock.
• When measuring the main circuit capacitor capacity (Pr. 259
Main circuit capacitor life measuring = "1"), the DC voltage is
applied to the motor for 1s at powering off. Never touch the
motor terminal, etc. right after powering off to prevent an
electric shock.
2. Fire Prevention
CAUTION
• Inverter must be installed on a nonflammable wall without
holes (so that nobody touches the inverter heatsink on the rear
side, etc.). Mounting it to or near flammable material can cause
a fire.
• If the inverter has become faulty, the inverter power must be
switched OFF. A continuous flow of large current could cause a
fire.
• Do not connect a resistor directly to the DC terminals P/+ and
N/-. Doing so could cause a fire.
3. Injury Prevention
CAUTION
• The voltage applied to each terminal must be the ones
specified in the Instruction Manual. Otherwise burst, damage,
etc. may occur.
• The cables must be connected to the correct terminals.
Otherwise burst, damage, etc. may occur.
• Polarity must be correct. Otherwise burst, damage, etc. may
occur.
• While power is ON or for some time after power-OFF, do not
touch the inverter since the inverter will be extremely hot.
Doing so can cause burns.
4. Additional Instructions
Also the following points must be noted to prevent an accidental failure,
injury, electric shock, etc.
(1) Transportation and installation
CAUTION
• The product must be transported in correct method that
corresponds to the weight. Failure to do so may lead to injuries.
• Do not stack the boxes containing inverters higher than the
number recommended.
• The product must be installed to the position where withstands
the weight of the product according to the information in the
Instruction Manual.
• Do not install or operate the inverter if it is damaged or has
parts missing. This can result in breakdowns.
• When carrying the inverter, do not hold it by the front cover or
setting dial; it may fall off or fail.
• Do not stand or rest heavy objects on the product.
• The inverter mounting orientation must be correct.
• Foreign conductive bodies must be prevented to enter the
inverter. That includes screws and metal fragments or other
flammable substance such as oil.
• As the inverter is a precision instrument, do not drop or subject
it to impact.
• The inverter must be used under the following environment:
Otherwise the inverter may be damaged.
Surrounding air
-10°C to +50°C (non-freezing)
temperature
Ambient humidity 90% RH or less (non-condensing)
Storage temperature -20°C to +65°C
Indoors (free from corrosive gas, flammable
Atmosphere
gas, oil mist, dust and dirt)
Maximum 1000m above sea level for
Altitude, vibration
standard operation. 5.9m/s
55Hz (directions of X, Y, Z axes)
*1 Temperature applicable for a short time, e.g. in transit.
2
*2 2.9m/s or less for the 185K or more.
*1
2
or less at 10 to
*2
A-1