Mitsubishi Electric F700 Instruction Manual page 165

REVISIONS
*
Print Date
Manual Number
Dec. 2003 IB(NA)-0600176ENG-A
Mar. 2004 IB(NA)-0600176ENG-B
Jun. 2004 IB(NA)-0600176ENG-C
Oct. 2004 IB(NA)-0600176ENG-D
Mar. 2005 IB(NA)-0600176ENG-E
Jul. 2006 IB(NA)-0600176ENG-F
Oct. 2007 IB(NA)-0600176ENG-G
Sep. 2009 IB(NA)-0600176ENG-H
For Maximum Safety
• Mitsubishi inverters are not designed or manufactured to be used in equipment or systems in situations that
can affect or endanger human life.
• When considering this product for operation in special applications such as machinery or systems used in
passenger transportation, medical, aerospace, atomic power, electric power, or submarine repeating
applications, please contact your nearest Mitsubishi sales representative.
• Although this product was manufactured under conditions of strict quality control, you are strongly advised
to install safety devices to prevent serious accidents when it is used in facilities where breakdowns of the
product are likely to cause a serious accident.
• Please do not use this product for loads other than three-phase induction motors.
158 IB(NA)-0600176ENG-H
*The manual number is given on the bottom left of the back cover.
First edition
Additions
FR-F740-0.75K to 30K
Additions
FR-F740-75K, 90K
Additions
⋅ FR-F720 - 0.75K to 55K
⋅ FR-F740 - 110K to 160K
⋅ Pr.299 Rotation direction detection selection at restarting
Additions
FR-F720 - 75K to 110K
⋅
⋅ FR-F740 - 185K to 560K
Additions
⋅ Pr. 539 Modbus-RTU communication check time interval
⋅ Voltage/current input switch
⋅ Setting value "2" of Pr. 882 Regeneration avoidance operation selection
Additions
Additional explanation to "Causes and Corrective Actions"
⋅ Setting values "10, 11" of Pr. 495 Remote output selection
⋅ Partial review of Instructions for UL and cUL Compliance
Partial changes
⋅ Replacement procedure of the cooling fun of FR-F740-185K or more
Additions
Pr. 59 Remote function selection setting value "11 ", "12 ", "13 "
Pr. 29 Acceleration/deceleration pattern selection setting value "6"
Pr. 30 Regenerative function selection setting value "10", "11", "20", "21"
Pr.128 PID action selection setting value "110", "111", "120", "121"
Pr.167 Output current detection operation selection setting value "10", "11"
Pr. 261 Power failure stop selection setting value "21", "22"
Pr.522 Output stop frequency
Pr.653 Speed smoothing control
,
Pr.553 PID deviation limit
,
display bias coefficient C43 (Pr.934) PID display bias analog value
,
display gain coefficient C45 (Pr.935) PID display gain analog value
Pr.799 Pulse increment setting for output power
DC feeding operation permission signal (X70), DC feeding cancel signal
(X71), PID integral value reset signal (X72)
PID deviation limit signal (Y48), Pulse output of output power signal (Y79),
DC feeding signal (Y85)
Partial changes
Pr.153 Zero current detection time setting range "0 to 10s"
5.5 Check first when you have a trouble
Appendix 3 Instructions for compliance with the EU Directives
Revision
,
Pr.654 Speed smoothing cutoff frequency
Pr.554 PID signal operation selection
,
C42 (Pr.934) PID
,
C44 (Pr.935) PID