AMT Datasouth AMTACCEL-5350 User Manual page 187

Table D-3. AMT and Diablo 630 Escape Sequences––continued
Function
Set character spacing ........
5 characters/inch .....
6 characters/inch .....
6.6 characters/inch .....
7.5 characters/inch .....
8.5 characters/inch .....
10 characters/inch .....
12 characters/inch .....
13.3 characters/inch .....
15 characters/inch .....
17.1 characters/inch .....
20 characters/inch .....
Set character spacing ........
to default
Set character cell width ....
5 characters/inch .....
6 characters/inch .....
6.6 characters/inch .....
7.5 characters/inch .....
8.5 characters/inch .....
10 characters/inch .....
12 characters/inch .....
13.3 characters/inch .....
15 characters/inch .....
17.1 characters/inch .....
20 characters/inch .....
Set horizontal .....................
spacing offset
ASCII Hexadecimal
ESC US n 1B 1F n
ESC US EM 1B 1F 19
ESC US NAK 1B 1F 15
ESC US DC3 1B 1F 13
ESC US DC1 1B 1F 11
ESC US SI 1B 1F 0F
ESC US CR 1B 1F 0D
ESC US VT 1B 1F 0B
ESC US LF 1B 1F 0A
ESC US HT 1B 1F 09
ESC US BS 1B 1F 08
ESC US BEL 1B 1F 07
ESC S 1B 53
ESC @ Z n 1B 40 5A n
ESC @ Z 8 1B 40 5A 38
ESC @ Z 4 1B 40 5A 34
ESC @ Z 2 1B 40 5A 32
ESC @ Z 0 1B 40 5A 30
ESC @ Z . 1B 40 5A 2E
ESC @ Z , 1B 40 5A 2C
ESC @ Z * 1B 40 5A 2A
ESC @ Z ) 1B 40 5A 29
ESC @ Z ( 1B 40 5A 28
ESC @ Z ' 1B 40 5A 27
ESC @ Z & 1B 40 5A 26
ESC DC1 n 1B 11 n
Decimal
Horizontal Spacing
27 31 n This sequence sets the distance that the carriage moves
27 31 25 after printing a character or when spacing. The value of
27 31 21 variable n minus one defines a number of 1/120-inch
27 31 19 increments to move:
27 31 17
27 31 15 Character spacing = (n - 1) x 1/120-inch
27 31 13
27 31 11
27 31 10
27 31 9
27 31 8
27 31 7
27 83 This sequence sets character spacing to the default spacing
of the active font. Each font has a default character spacing
that the printer uses when no character spacing is set.
Courier is 10 characters per inch (cpi); Letter Gothic and
Elite are 12 cpi; Trend is proportional; and so on.
With double-wide printing on, this sequence sets character
spacing to two times the default character spacing of the
active font. If the active font is proportional, this sequence
turns on the proportional mode.
27 64 90 n This sequence sets the width of character cells. Normally,
27 64 90 56 if you print a font at a character spacing other than the
27 64 90 52 default spacing, the characters overlap or are spaced too far
27 64 90 50 apart. This sequence automatically proportions characters
27 64 90 48 so that they print correctly at other valid character spacings.
27 64 90 46
27 64 90 44 The value of variable n minus 32 determines the width, in
27 64 90 42 1/120-inch increments, for each character cell. If the active
27 64 90 41 font is proportional, variable n determines the width of a
27 64 90 40 space (SP); all other character cells adjust proportionally.
27 64 90 39
27 64 90 38 This sequence does not change the current character
spacing. To print a font at a nonstandard pitch, include this
escape secquence between the Set Font and Set Character
Spacing sequences.
27 17 n This sequence causes an offset of 0/120-inch to 63/120-inch
to be added to or subtracted from the current character
spacing (or PS unit values, if the PS mode is on). Variable
n is a byte that determines whether the offset is added or
subtracted, and the distance of the offset. The printer
interprets n as follows:
Reads the value of bit 6 to determine whether the offset
is positive or negative. If the bit equals 0, the offset is
positive and the printer adds it; if the bits equals 1, the
offset is negative and the printer subtracts it.
User's Guide
Description
Code Sets D-9