Minolta EP1030 Manual page 4

CONTENTS
3-1. JIGS AND TOOLS USED ........... 0... ccc cece eae e ees D-39
3-2, ADJUSTMENT REQUIREMENTS LIST .................008 D-40
3-3. ACCESSING THE TECH. REP. MODE .................... D-41
3-4, ELECTRICAL/IMAGE ADJUSTMENTS .................... D-42
(1) Adjustment of the Maximum Exposure Lamp Voltage for
the Manual Mode ............ cc ccc cece eee eec cues eenees D-42
(2) Adjustment of Optimum Exposure Setting in the Manual
Exposure Mode .......... 0. ccc cece eee ene e ence eaes D-44
| (3) Adjustment of Exposure Level in the Auto
=
Exposure Mode ........ 2.0.0 cece cece cee eeeeecneuenees D-46
(4) ATDC Adjustment ...............0.0008 egherunaetaadcn D-47
(5) Adjustment of the Aperture Blades ......... i Sarate
nar eare teats D-48
(6) Adjustment of Zoom Ratio in the Crosswise Direction
|
(EP1031/EP1031F Only) ........
cc cece eee eeecaeeccecs D-49
(7) Adjustment of Zoom Ratio in the Feeding Direction
....... D-51
(8) Adjustment of the Reference Position of
the Manual Bypass Table ...............cc
cc ceeeeeeeeas D-53
(9) Adjustment of Paper Feed Cabinet
:
Reference Position .........
0... ccc e cece eee eee eneues D-54
|
(10) Adjustment of the Leading Edge Registration
........... D-55
eLeading Edge Registration in Full Size Mode
.......... D-55
Leading Edge Registration in Enlargement Mode
(EP1031/EP1031F only) ...........
ccc cece cece eee e es D-57
@Leading Edge Registration in Reduction Mode
(EP1031/EP1031F only) ............
cc ccee cece eee es D-59
(11) Adjustment of the Image Leading Edge Erase Width ..... D-61
(12) Adjustment of Edge Erase (EP1031/EP1031F
only) ...... D-63
(13) Adjustment of SDH Reference Position
(EP1030F/EP1031F Only) ..........cc
cece cece cece ees D-64
(14) Adjustment of SDH Leading Edge Registration
ar,
(EP1030F/EP1031F Only) ............
0... ccc cece anes D-65
(15) Adjustment of SDH Center Alignment
,
(EP1030F/EP1031F Only) ............
0... ccc cece ees D-67
3-5. OTHER ADJUSTMENT
2... . cc cece cece eee e ence eeteees D-68
(1) Focus-Positioning of the Scanner and Mirrors
Carmage vein ndssaueg tet veka tenes $e dad wade eaciunieead D-68
3-6. POWER SOURCE VOLTAGE ROOT-MEAN-SQUARE-
VALUE-TO-MEAN-VALUE CONVERSION TABLE ........... D-69
V
iii i
1139SBD0100A
im SERVICE INSTRUCTIONS
115SSBDOI01A
1-1. PRECAUTIONS FOR DISASSEMBLY/ADJUSTMENTS
Observe the following precautions whenever servicing the copier.
© Be sure to unplug the copier from the outlet before attempting to service the copier.
© The basic rule is not to operate the copier anytime during disassembly.
If it is absolutely nacessary to run the copier with its covers removed, use care not to allow your clothing
to be caught In revolving parts such as the timing belt and gears.
® Be sure to use the Interlock Switch Actuating Jig whenever it is necessary to actuate the Interlock Switch
with the covers left open or removed.
® Do not plug in or unplug print jacks on the Board or connect or disconnect the Board connectors while
power is being supplied to the copier. :
© Do not use flammable spray around the copier in operation.
@ The Magnet Roller of the Imaging Unit generates strong magnetic force. Do not bring it near a cathode-ray
tube or watch. ;
© Do not use an air gun or vacuum cleaner for cleaning the ATDC Sensor and other sensors, as they can
cause electrostatic destruction. Use a blower brush and cloth. If a unit containing these sensors is to ba
cleaned, first remove the sensors from the unit.
@ When handling the PWBs with MOS ICs, observe "Instructions for Handling the PWBs with MOS ICs."
@ When handling the PC Drum, observe precautions given in "Handling of the PC Drum."
® Note that replacement of a PWB may call for readjustments or resetting of particular items.
@ Use the right screw in the right place at reassembly. Note that some are longer and some are thicker than
others.
@ A toothed washer is used with the screw that secures the ground wire to ensure positive conduction. Do
not forget to insert this washer at reassembly.
© To reassemble the copier, reverse the order of disassembly unless otherwise specified.
© If it becomes necessary to replace the thermal fuse or any other fuse mounted on a board, be sure to use
one of the rating marked on the blown fuse.
Always note the rating marked on the fuse, as the rating and mounting site or number used are subject
to change without notice.
@ Donot pull out the Toner Hopper while the Toner Bottle is turning, as a damaged Toner Replenishing Motor
or locking mechanism could result.
If the copier is to be run with the Front Door swung down, make sure that the Toner Hopper is in the locked
position.