Table of Contents
Advertisement
4-9. Function setting list
No.
Item
P01
Maximum sewing speed
P02
Tilt of the pedal
P04
Reverse feed stitching
speed at the beginning of
sewing
P05
Reverse feed stitching
speed at the end of sewing
P06
Overlapped stitching speed
P07
Sewing speed for soft start
P08
Soft start function
P09
Sewing speed for the polyg-
onal-shape stitching
P10
Setting of the reverse feed
stitching at the end of end of
polygonal-shape stitching
P12
Changeover of the reverse
feed stitching at the start
of sewing between Auto /
Manual
P13
Function of stop immedi-
ately after the reverse feed
stitching at the beginning of
sewing
P15
Changeover of the needle
up/down correction function
P16
Speed limit to reverse-feed
stitching
P18
Correction of solenoid-on
timing for the reverse feed
stitching at the beginning of
sewing
P19
Correction of solenoid-off
timing for the reverse feed
stitching at the beginning of
sewing
＊
P21
Low-speed section by pedal Acceleration position by pedal operation is set.
＊
P22
Sewing starting position by
pedal
＊
P23
Position to lift the presser
foot by pedal
＊
P24
Position to perform thread
trimming by pedal
＊ Do not change the set values with asterisk (*) mark as they are functions for maintenance. If the standard set value set at the time
of delivery is changed, it is in danger of causing the machine to be broken or the performance to be deteriorated. If it is necessary to
change the set value, please purchase the Engineer's Manual and follow the instructions.
Description
The maximum sewing speed reached by fully depressing the
pedal is set with this function setting item. The maximum sewing
speed can be changed within the sewing speed range specified
for [P68 Maximum sewing speed].
* The maximum sewing speed can also be changed using the +
- switch on the operation panel.
Change in the sewing speed with respect to the depressing depth
of the pedal is set with this function setting item.
The sewing speed is increased abruptly when this parameter is
set to a large value, or increased slowly when this parameter is
set to a small value.
The sewing speed to be used during the reverse feed stitching at
the beginning of sewing is set with this function setting item.
The sewing speed to be used during the reverse feed stitching at
the end of sewing is set with this function setting item.
The sewing speed to be used during the overlapped stitching is
set with this function setting item.
* This speed can also be changed using the relevant switch on
the operation panel.
The sewing speed for soft start at the beginning of sewing is set
with this function setting item.
The number of stitches to be sewn with the soft-start function at
the beginning of sewing is set with this function setting item.
0: The soft-start function is not selected
1 - 99: The number of stitches to be sewn with the soft-start
function
Sewing speed for the polygona-shape stitching is set with this
function setting item.
* The sewing speed can also be changed using the + - switch on
the operation panel.
Whether the reverse feed stitching is automatically carried out
at the end of polygonal-shape stitching is set with this function
setting item.
ON: Reverse feed stitching is automatically performed at the
end of sewing
OFF: Sewing machine stops sewing before starting reverse
feed stitching at the end of sewing. It performs reverse feed
stitching when the front part of pedal is depressed.
The sewing speed for the reverse feed stitching at the beginning
of sewing is set with this function setting item.
0: The reverse feed stitching is performed by manually operating
the pedal.
1: The reverse feed stitching is performed at the sewing speed
set with [P04 Reverse feed stitching speed at the beginning of
sewing].
Operation to be carried out at the end of the reverse feed stitching
at the beginning of sewing is selected with this function setting
item.
CON: The sewing machine does not stop temporarily after com-
pletion of the reverse feed stitching at the beginning of sewing
STP: The sewing machine stops temporarily after completion of
the reverse feed stitching at the beginning of sewing
The function of needle up/down correction switch is changed over
with this function setting item.
0: Needle up/down correction
1: One stitch correction
2: Continuous half stitch
3: Continuous one stitch
4: Count number of pieces sewn
The speed limit applied when reverse feed stitching is carried out
is set with this function.
100 - 4000: Sewing is performed at the set sewing speed
Stitch alignment can be carried out by changing the timing of
actuating the reverse-feed stitching solenoid at the time of reverse
feed stitching at the beginning of sewing. When the set value for
this parameter is increased, the length of stitch at the end of A
process is increased and the length of stitch at the beginning of B
process is decreased.
Stitch alignment can be carried out by changing the timing of
releasing the reverse-feed stitching solenoid at the time of reverse
feed stitching at the beginning of sewing. When the set value for
this parameter is increased, the length of stitch at the beginning of
B process is increased.
Sewing starting position by pedal operation is set.
The position to lift the presser foot by operating the pedal is set
with this function setting item.
The position to perform thread trimming by operating the pedal is
set with this function setting item.
– 40 –
Level
Setting range
Default
U
100-[P68]
4000
(sti/min)
S
10-100(%)
80
U
100-3000
1900
(sti/min)
U
100-3000
1900
(sti/min)
U
100-3000
1900
(sti/min)
U
100-1500
800
(sti/min)
U
0-99
1
(Stitches)
U
200-[P68]
4000
(sti/min)
U
ON/OFF
ON
U
0-1
1
U
CON/STP
CON
U
0-4
0
S
100-4000
2000
(sti/min)
U
0-200
123
U
0-200
130
S
30-1000
520
S
30-1000
420
S
30-1000
270
S
30-500
130
Advertisement
Table of Contents
