Sis Command And Response Table For Input-Endpoint-Specific Commands - Extron electronics XTP II CrossPoint 1600 User Manual

SIS Command and Response Table for Input-Endpoint-Specific Commands

The table that starts below shows commands that affect the following endpoints connected
through XTP input boards only:
•
•
•
•
The XTP II CrossPoint switcher acts as a master, forwarding the commands to the endpoint
slave.
Command Function
EDID commands
NOTE: Leading zeroes are optional for the entry of the inputs (
Assign EDID data to an input
Example
(XTP II CrossPoint 3200):
Example
(XTP II CrossPoint 1600):
Assign EDID data to all inputs
View EDID assignment
Save output 1 EDID to user
assigned slot
X$
NOTE: For this command,
(XTP II CrossPoint 3200), or
Example
(XTP II CrossPoint 3200):
Example
(XTP II CrossPoint 1600):
Audio input gain and attenuation
NOTE: The set gain ( ) and set attenuation (
G
Set audio input gain to +dB value
Example:
Set audio input attenuation to -dB
value
Increment gain
Example:
Decrement gain
Example:
Read input gain
Example:
NOTE: X$ = EDID value (resolution and rate)
X^ = Input number (for other than tie)
X& = Audio gain
X* = Numeric dB value
X( = Audio attenuation
XTP T HDMI transmitter
XTP T USW 103 switcher
XTP T VGA transmitter
XTP T FB 202 floor box switcher
SIS Command
(Host to Unit to Endpoint)
X^
E X^ X$ }
A * EDID
E }
A7*36EDID
E }
A7*36EDID
E X$ }
A* *EDID
E X^ }
A EDID
E X$ }
S EDID
is valid only in the range of through
117
through (XTP II CrossPoint 6400).
165 228
E }
S133EDID
E }
S117EDID
) commands are case sensitive.
g
X^ X&
* G
1*2G
X^ X(
* g
X^
+G
5+G
X^
-G
7-G
X^
G
3G
See table 9 beginning on page 88.
– , , or
01 16 32 64
– (1 dB per step)
0 24
(43 steps of gain or attenuation) (default = 0 dB)
–18 to +24
– (1 dB per step)
1 18
XTP II CrossPoint 1600, 3200, and 6400 Switchers • Programming Guide
• XTP T UWP 202 wallplate switcher
• XTP T UWP 302 wallplate switcher
• XTP T EU 202 wallplate switcher
• XTP T MK 202 wallplate switcher
Response Additional Description
(Endpoint to Unit to Host)
X$
s) and EDID values ( s). Leading zeroes are reported in the response.
X^ X$]
Assign an EDID value of
EdidA *
]
Assign an EDID value of 1280x720 at
EdidA07*036
60 Hz to input 7.
]
Assign an EDID value of 1600x900 at
EdidA07*036
60 Hz to input 7.
X$]
Assign an EDID value of
EdidA00*
X$]
X$]
Save the output 1 EDID to location
EdidS
(XTP II CrossPoint 1600),
124
]
Save the output 1 EDID to user location 1.
EdidS133
]
Save the output 1 EDID to user location 1.
EdidS117
X^ X*]
In •Aud
]
Set input 1 audio gain to +2 dB.
In01•Aud+02
X^ X*]
In •Aud
X^ X*]
Increase gain by 1 dB.
In •Aud
]
Increase audio input 5 level from +2 dB
In05•Aud+03
to +3 dB.
X^ X*]
Decrease gain by 1 dB.
In •Aud
]
Decrease audio input 7 level from -8 dB
In07•Aud-09
to -9 dB.
X*]
]
Audio input 3 level is at -6 dB.
-06
X$ X^
to input
X$
to all inputs.
X$
through
133 140
.
.
95