Extron electronics XTP II CrossPoint 1600 User Manual page 109

SIS Command and Response Table for Input-Endpoint-Specific Commands (continued)
Command Function
XTP T FB 202, XTP T UWP 202, and XTP T UWP 302 switcher specific commands (continued)
HDCP status
View input HDCP status
View HDCP status of all inputs
Input video format
Set format
Example:
View format
Image reset
Execute an image reset
Pixel phase (available for RGBHV and non-interlaced component video (YUVp) video inputs)
Set a specific pixel sampling phase
Increment sampling value
Decrement sampling value
View the sampling value
Horizontal shift
Specify a value
Increment value
Decrement value
View
Vertical shift
Specify a value
Increment value
Decrement value
View
Input sync detection
View all input connections
Example
(XTP II CrossPoint 3200):
NOTE: X%
= Input signal status
X^ = Input number (for other than tie)
X1# = HDCP authorized device
X1$ = HDCP status (for inputs)
X3) = Input video source
X3!
= Detected video format
X3@ = Picture adjustments
X3# = Shift
SIS Command Response
(Host to Unit to Endpoint) (Endpoint to Unit to Host)
E X^ } X1$]
I HDCP
E } X1$
I*HDCP
X^ X3)
* \ Ityp
1*0\
Ityp01*0*5
X^ X3)
\
X^
A Aadj
E X^ X3@ }
I * PHAS PhasI
E X^ }
I +PHAS PhasI
E X^ }
I –PHAS PhasI
E X^ } X3@]
I PHAS
E X^ X3# }
I * HCTR HctrI
E X^ }
I –HCTR HctrI
E X^ }
I +HCTR HctrI
E X^ } X3#]
I HCTR
E X^ X3# }
I * VCTR VctrI
E X^ }
I +VCTR VctrI
E X^ }
I –VCTR VctrI
E X^ } X3#]
I VCTR
X%
0LS
0LS
Response Status:
= No signal detected
0
– , , or
01 16 32 64
= Off
0
= No source device connected
0
= Source connected is HDCP-compliant
1
= Auto (default)
0
= Video
1
2 = S-video
0 = no signal detected
1 = Video
2 = S-video
000 through 255 (128 = default)
00000 through 65535
XTP II CrossPoint 1600, 3200, and 6400 Switchers • Programming Guide
Additional Description
X1$ X1$ X1$ ]
...
1 2 3 n
X^ X3) X3!]
Set input
* *
endpoint reports the detected video
format,
]
Set input 1 to auto. The endpoint
reports RGB video.
X3!]
View set (
*
format of input
X^]
Reset input signal timing to Extron
default for input
X^ X3@]
Specify the pixel sampling phase.
*
X^ X3@]
Increase the phase value.
*
X^ X3@]
Decrease the phase value.
*
Show the pixel sampling phase.
X^ X3#]
Set the horizontal location of first active
*
pixel in input
X^ X3#]
Increase the value by one pixel (shift the
*
image to the right).
X^ X3#]
Decrease the value by one pixel (shift
*
the image to the left).
Show the horizontal location of first
active pixel in input
X^ X3#]
Set the vertical location of first active
*
pixel in input
X^ X3#]
Increase the value by one line (shift up).
*
X^ X3#]
Decrease the value by one line (shift down).
*
Show the vertical location of first active
pixel in input
X% X% X% ]
16, 32, or 64 (
...
1 2 3 n
status of an input, starting from input 1.
Sync detected
No input detected
0 0 0 1 1 1 0 1 0 0 1 0 1. . .0
Input: 1 2 3 4 5 6 7 8 9 10111213
= Sync detected
1
= On (default)
1
= Source connected is not HDCP-compliant
2
= RGBcvS (SCART)
3
4 = YUV interlace
3 = RGBcvS (SCART)
4 = YUV interlace
X^ X3)
to video format. The
X3!
, in the response.
X3) X3!
) and detected ( ) video
X^
.
X^
.
X^
.
X^
.
X^
.
X^
.
X%
) s; each is the connection
n
Sync detected
32
= RGB
5
6 = YUV
5 = RGB
6 = YUV
101