Extron electronics XTP II CrossPoint 1600 User Manual page 124

X6%
= GMT offset
X6^
= Daylight Savings Time
X6&
= IP address
X6*
= Hardware (MAC) address
X6(
= Number of open connections
X7)
= Password
NOTE: The HTML language reserves certain characters for specific functions (see
X7!
= Domain name
NOTE: The HTML language reserves certain characters for specific functions (see
acceptable only as the lead-in to the domain name (such as @extron.com).
X7#
= E-mail account
X7$
= E-mail address
X7%
= Notification selections, part 1
X7^
= Notification selections, part 2
X7&
= Notify when?
X7*
= DHCP
X7(
= Port number
X8)
= Baud rate
X8!
= Parity
X8@
= Data bits
X8#
= Stop bits
X7( X8#
NOTE: through and
X8$
= Port type
X8%
= Verbose mode
NOTE: If tagged responses is enabled (modes 2 and 3), all read commands return the constant string and the value as the set command
does (for example, the read matrix name command
X8^ = Flow control
X8&
= Data pacing (in ms between bytes)
X8*
= Time (in 10 ms increments) to wait for characters
X8(
= Time (in 10 ms increments) between characters
X9)
= Priority status for receive timeouts :
X9!
= Length of message ( ) or delimiter (
L
X9@
= Port timeout interval (in 10-second increments)
. through
–12 0
= Daylight Savings Time off or ignore
0
= Daylight Savings Time on (North America)
1
= Daylight Savings Time on (Europe)
2
= Daylight Savings Time on (Brazil)
3
###.###.###.###
##-##-##-##-##-##
-
000 200
Up to 12 alphanumeric characters
Standard domain name rules apply (for example: xxx.com)
- .
65 72
Typical e-mail address format (for example: nnnn@xxx.com)
= inputs
I
X7% X7^
If = I, then = 00 (all inputs), or 01 through 16 , 32 , or 64 (input 1 through 16 [32 or 64])
X7% X7^
If = F, then = 00 (all fans)
X7% X7^
If = P, then = 00 (all power supplies).
= no response
0
1 = fail/missing
= off (default),
0
01 = Remote RS-232/RS-422 port
—
03 130
9600 (default),
odd, even, none, mark, space (only the first letter required) (n = default)
7 , 8 (default)
(default),
1
X9@ X1^
are repeated on page 78 as
= RS-232 (default)
0
= Clear or none (default for Telnet connection)
0
= Verbose mode (default for RS-232/RS-422 or USB connection)
1
= Tagged responses for queries
2
= Verbose mode and tagged for queries
3
E }
CN
hardware, software, none (only the first letter required) (n = default)
(default) -
0000
(= 100 ms, default) -
10
(= 20 ms, default) -
2
= Use the "Send" data string command parameters if they exist (default)
0
= Use the Configure receive timeout command parameters
1
)
D nnnnnL
<delimiter
(= 10 seconds) -
1
XTP II CrossPoint 1600, 3200, and 6400 Switchers • Programming Guide
. . Hours and minutes removed from GMT
+14 0
Special Characters
Special Characters
= e-mail recipient 1, = 2,
65 66 67
= fans
F
= fixed or restored
2
3 = both 1 & 2
= on
1
= UARTs 1 — 128 (XTP input and output board ports)
19200 , 38400 , 115200
2
X2!
through .
X1@]
, returns Ipn• ).
1000
32767
32767
= byte count ( – or = ignore byte length, use time)
1 32767 0
> (For example: [carriage return —
D 13D
(default is = 300 seconds = 5 minutes)
65000 30
on page 118).
on page 118). The @ character is
= 3, ... = recipient #8
72
= power supply
P
= suspend
4
02 Unused
= RS-422
1
}
])
116