Sis Command And Response Table For Ip-Specific Commands - Extron electronics XTP CrossPoint 1600 Setup Manual

Command
Input audio selection
NOTE: These commands select between the audio embedded in the digital video stream and the 2-channel analog audio.
Input audio selection
Example:
View input audio selection
View all input audio
selections
Audio input gain and attenuation
NOTE: The set gain (G) and set attenuation (g) commands are case sensitive.
Set input level to +dB value
Example:
Set input level to -dB value
Increment gain
Example:
Decrement gain
Read input level
NOTE: • = Space
X!
= Input number
X1!
= Input audio source
X1@
= Audio gain
X1#
= Numeric dB value
X1$
= Audio attenuation
Command
List Digital Sync Validation Processing (DSVP)
List sync of all inputs
Example
(XTP CrossPoint 3200):

SIS Command and Response Table for IP-Specific Commands

NOTE: These commands allow you to control and monitor the IP functions of the XTP CrossPoint matrix switcher .
Command
IP and serial port setup
Set IP address
Read IP address
Set subnet mask
Read subnet mask
Set gateway IP address
Read gateway IP address
Set DHCP on or off
Read DHCP on/off status
X1&
NOTE: = Signal detection status
X2(
= IP address
X3)
= DHCP
SIS Command Response
(Host to Unit to Endpoint) (Endpoint to Unit to Host)
E X! X1! }
I * AFMT AfmtI
E }
I1*0AFMT AfmtI1*0
E X! } X1!]
I AFMT
E } X1! X1!
IAFMT
1
X! X1@ X!
* G In
1*2G In01•Aud+02
X! X1$ X!
* g In
X! +G In X!
5+G
In05•Aud+03
X! X!
–G In
X! X1#]
G
01 – 16 or 32
0 = auto (see the example above)
1 = HDMI (de-embedded digital audio) (default)
0 to +24 (1 dB per step)
–18 to +24 (45 steps of gain or attenuation) (Default = 0 dB)
1 – 18 (1 dB per step)
SIS Command Response
(Host to Unit to Endpoint) (Endpoint to Unit to Host)
X1& X1&
0LS
1
0LS
no input detected
Response Status:
SIS Command
(host to unit)
EX2( }
CI
E }
CI
EX2( }
CS
E }
CS
EX2( }
CG
E }
CG
EX3) }
DH
E }
DH
0 = no input connected
. . .
nnn nnn nnn
0 = off, 1 = on
Additional Description
X! X1!]
*
]
Auto (0): Digital audio takes priority over analog audio.
X1! X1! ] X1!
...
2 3 n Each is the enable or disable status of an output, starting
at output 1. n is 16 or 32.
X1#]
•Aud
]
Set input 1 audio gain to +2 dB.
X1#]
•Aud
X1#]
•Aud Increase gain by 1 dB.
]
Increase audio input 5 level from +2 dB to +3 dB.
X1#]
•Aud Decrease gain by 1 dB.
2 = Analog (local 2-channel audio)
Additional Description
X1& X1& ]
...
2 3 n 16 or 32 (
n
from input 1.
input detected
0 0 0 1 1 1 0 . . . 0
Input: 1 2 3 4 5 6 7 32
Response
(unit to host)
X2(]
Ipi
X2(]
X2(]
Ips
X2(]
X2(]
Ipg
X2(]
X3)]
Idh
X3)]
1 = input connected
nnn
X1&
) s; each is the signal status of an input, starting
Additional Description
Default: 192.168.254.254
Default: 255.255.0.0
Default: 0.0.0.0
Default: 0 (Off)