Table of Contents
Advertisement
5820A
Operators Manual
programming the, 5-40
STB remote command, 6-37
STBY remote command, 6-38
Summary of commands and queries, 6-8
Syntax
information, general, 5-33
parameter rules, 5-33
response messages, 5-36
—T—
Tab characters, 5-34
Taking an impedance measurement, 5-47
TDPULSE remote command, 6-38
TDPULSE? remote command, 6-38
Terminators, 5-35
Testing overload protection, 4-34
Testing RS-232 host port operation using a
terminal, 5-13
Testing RS-232 host port operation using Visual
Basic, 5-15
Testing RS-232 UUT port operation using Visual
Basic, 5-20
Testing RS-232 UUT port operation via a terminal,
5-19
Testing the IEEE-488 port, 5-8
Testing the RS-232 host port, 5-13
Testing the RS-232 UUT port via IEEE-488 port,
5-21
Testing the RS-232 UUT port via RS-232 host port,
5-17
Testing video triggers, 4-29
Time base calibration, 4-24
Time marker function
specifications, 8-6
Time marker, oscilloscope calibration, 4-25, 4-26
TLIMIT remote command, 6-38
TLIMIT? remote command, 6-38
TLIMIT_D remote command, 6-39
TLIMIT_D? remote command, 6-39
TMWAVE remote command, 6-39
TMWAVE? remote command, 6-39
TRIG remote command, 6-40
TRIG? remote command, 6-40
TRIG_CHAN remote command, 6-41
TRIG_CHAN? remote command, 6-41
Trigger menu, 4-14, 4-16, 4-26, 4-31
Trigger menu, oscilloscope calibration, 4-14, 4-16,
4-26
Trigger menu, verifying pulse capture, 4-31
Trigger tests for oscilloscope, 4-27
Tunnel diode pulser verification, 7-20
Turning on the calibrator, 4-3
Types of commands, 5-28
6
—U—
Unpacking, 2-3
Using auxiliary input, 4-35
Using commands, 5-26
Using operate and standby modes, 4-7
Using the format EEPROM menu, 4-6
Using the instrument setup menu, 4-5
Using the setup menu, 4-4
Using the softkeys, 4-4
Utility functions menu, 4-5
UUT Port
controlling an instrument, 5-48
UUT_FLUSH remote command, 6-42
UUT_RECV? remote command, 6-42
UUT_SEND remote command, 6-43
UUT_SET remote command, 6-44
UUT_SET? remote command, 6-44
—V—
V/DIV menu, 4-13
VAL? remote command, 6-45
Values, keying in, 4-9
Verification
AC amplitude, 7-7
AC voltage frequency, 7-8
DC voltage, 7-6
edge, amplitude, 7-19
edge, duty cycle, 7-19
edge, frequency, 7-19
edge, rise time, 7-20
input impedance, capacitance, 7-21
input impedance, resistance, 7-21
leveled sinewave, 7-11
leveled sinewave, flatness, 7-13
leveled sinewave, frequency, 7-11
leveled sinewave, harmonics, 7-12
marker generator, 7-20
pulse generator, period, 7-21
pulse generator, pulse width, 7-21
tunnel diode pulser, 7-20
wave generator amplitude, 1 MΩ, 7-9
wave generator amplitude, 50 Ω, 7-10
wave generator frequency, 1 MΩ, 7-11
Verifying pulse capture, 4-30
trigger menu, 4-31
Video triggers, testing, 4-29
VIDEOFMT remote command, 6-45
VIDEOFMT? remote command, 6-45
VIDEOMARK remote command, 6-45
VIDEOMARK? remote command, 6-46
Visual Basic test program, creating, E-1
Volt function, 4-12
V/DIV menu, 4-13
Voltage gain calibration, 4-12, 4-14
Advertisement
Table of Contents
