Table of Contents
Advertisement
RANGE? remote command, 6-29
RANGELCK remote command, 6-30
RANGELCK? remote command, 6-30
Rear panel features, 3-3
REFOUT? remote command, 6-31
Registers
event status (ESR), 5-40
Event Status Enable (ESE), 5-40
Instrument Status (ISR), 5-42
Instrument Status Change (ISCR), 5-42
Instrument Status Change Enable (ISCE), 5-42
REMOTE command, 6-31
Remote control
using host port, 5-11, 5-16
using IEEE port, 5-4
Remote operation, 1-5
Remote operation (Chapter 5), 5-4
Remote operation (IEEE-488), 1-6
Remote program examples, 5-45
Remote state, 5-23
Remote with lockout state, 5-23
Replacing the line fuse, 7-3
RESET key, 3-6
Resetting the calibrator, 4-7
Response data types
binary block data, 5-36
floating, 5-36
indefinite ASCII, 5-36
integer, 5-36
string, 5-36
table of, 5-36
Response message syntax, 5-36
RS-232
controlling an instrument, 5-48
host port setup procedure, 5-11
using host port, 5-11, 5-16
UUT port setup procedure, 5-16
RS-232 Host Port commands, 6-6
RS-232 host port operation using a terminal, 5-13
RS-232 host port operation using Visual Basic, 5-15
RS-232 Host port setup procedure, 5-11
RS-232 host port, testing the, 5-13
RS-232 interface overview, 5-24
RS-232 modem cables, 9-4
RS-232 null-modem cables, 9-4
RS-232 remote control connections, 5-6
RS-232 UUT Port commands, 6-7
RS-232 UUT port operation using Visual Basic,
5-20
RS-232 UUT port operation via a terminal, 5-19
RS-232 UUT port setup procedure, 5-16
RS-232 UUT port testing via IEEE-488 port, 5-21
RS-232 UUT port testing via RS-232 host port,
RST remote command, 6-31
5-17
—S—
SBY key, 3-5
SCOPE remote command, 6-32
SCOPE? remote command, 6-34
Sequential commands, 5-31
Serial connector, D-2
Serial poll, status byte, 5-37
Service information, 2-7
Service request
SRQ line, 5-39
Service Request
Enable Register (SRE), 5-39
Setting frequency and voltage, shortcuts, 4-21
Setting up the RS-232 host port for remote control,
5-11
Setting up the RS-232 UUT port for remote control,
5-16
Setting voltage amplitude, shortcuts, 4-13
Setup and utility commands, 6-6
SETUP key, 3-6
Setup menu, 4-4
Setup menus
format EEPROM menu, 4-6
IEEE-488 port, 5-7
instrument setup, 4-5
RS-232 host port, 5-11
utility functions menu, 4-5
SETUP softkey menu tree, 3-10
Setup softkey menu trees, 3-10
Signal, adjusting during oscilloscope calibration,
4-8
Softkeys, using, 4-4
SP_SET, 6-34
SP_SET? remote command, 6-35
Specifications, 1-8
SPLSTR remote command, 6-35
SPLSTR? remote command, 6-36
SRE
programming the, 5-40
register, 5-39
SRE remote command, 6-36
SRE? remote command, 6-36
SRQ, service request line, 5-39
SRQSTR remote command, 6-37
SRQSTR? remote command, 6-37
Standard equipment table, 2-3
Starting oscilloscope calibration, 4-8
Status
checking 5820A, 5-37
register overview - figure, 5-38
register summary - table, 5-37
serial poll status byte, 5-37
Status commands, 6-7
STB
explained, 5-37
Index
(continued)
5
Advertisement
Table of Contents
