Connecting To A Home Wi-Fi Network - Lennox iComfort G71MPP-03 Setup Manual

equipment
setup tests
The Testing Process is finished
press 'tests' button to run more tests
press 'EXIT' button to start normal operation
9:39 am Aug 15, 2012
Figure 23. Testing Finished Screen
DE-HUMIDIFICATION AND ZONING
When using the iharmony™ Zoning System, de-humidification is disable and not
supported at this time. When using the iharmony™ Zoning System along with the
XC25 or XP25, zoning is support in non-zoned mode (central) only. If the system is
®
set to humid the iComfort Wi-Fi
(De-humidification) table blower speeds while a cooling and De-humidification call
exists. Without the De-humidification call or if set to moderate, the normal cfm table
is used. If set to Dry, the iComfort Wi-Fi
blower cfm.

CONNECTING TO A HOME WI-FI NETWORK

Check the router utility program or contact service provider for help. When
determining the location for the Wi-Fi thermostat, be sure it is in an area near enough
to the homeowners Wi-Fi router to ensure good communications signal between the
thermostat and the router. (Hint: use a smart phone with Wi-Fi and Wi-Fi finder
application to locate and determine signal strength.)
NOTE - Thermostat will not be able to reliably connect to a router if the received
signal strength indicator (RSSI) is -70 or greater.
NOTE - Correct the cause of any alerts prior to continuing setup.
Connection Recommended!
Verify the router is capable of, and set to operate in
wireless network "802.11b" mode. Check router utility program or contact service
provider for assistance.
ENABLING WI-FI
To enable the Wi-Fi feature to communicate with a wireless router
1. Press and release "Wi-Fi" in the lower left corner of the HOME screen
indoor temperature
indoor humidity is 41%
system is cooling
Wi-Fi
Wi-Fi
9:39 am Aug 15, 2012
1
Figure 24. Press Wi-FI
2. Press the Wi-Fi enable button.
507152-01
diagnostics
alerts
cancel next
thermostat will operate the blower at the comfort
®
thermostat uses the efficiency table for the
outdoor
temperature
set temp
80
75 heat
or
cool
cool-to
72
fan is
AUTO fan is fan is
Heat-to
AUTO OFF
Zone 1
?
WI-FIL SETTINGS
Wi-Fi
3. Press next as many times as necessary; then press accept after reading the
User Agreement.
ESTABLISHING A WI-FI CONNECTIONS
1. Press NETWORK SETTINGS; this screen shows a graphical view of buttons
representing Wi-Fi options OPEN and SECURE wireless networks and a
button for adding a network.
WI-FI SETTINGS
Wi-Fi
S
Open connection which which requires no password.
S
Secure connection which requires Wi-Fi password (security key).
S
Add a network is required when Wi-Fi identification (SSID) is being
hidden (not broadcasting). You will need to know the Wi-Fi network name
(SSID), security encryption type (if enabled), and security password (if
security encryption is enabled).
Secure
HOME
Open connection (no password required)
DS9
Secure connection (password required)
(lock icon is present)
BSG
enter
Signal strength. For best results, the higher the
away
bar levels, the more reliable a connection.
Figure 27. Typical Connection Type and Signal Strength
2. When selecting a:
S
unsecured connection a screen will appear with two options, connect
and AP info. Press connect to continue.
S
secured connection a screen will appear requesting the Wi-Fi network
password (security key). There are two options to select from which are
connect and AP info. Using the on-screen keyboard, enter the
password (security key) and then press connect to continue.
NOTE - AP info provides information concerning the home Wi-fi connection (i.e,
RSSI, IP address, MAC address and wait state) all of which may be helpful in
troubleshooting network connection issues).
Page 18
Thermostat is not connected to the Wi-FI network
WI-FI
disabled
Press to enable /
disable Wi-FI
Zone 1
9:39 am Aug 15, 2012
Figure 25. Enable Wi-FI
Thermostat is not connected to the Wi-FI network
WI-FI
NETWORK
SETTINGS
enabled
press to change
press to enable /
network settings
disable Wi-FI
Must setup a network connection before registering thermostat
Zone 1
9:39 am Aug 15, 2012
Figure 26. Enable Wi-FI
X
?
X
?
7/2013