Table of Contents
Advertisement
DE-HUMIDIFICATION SETTINGS — SYSTEM DEVICES SCREEN
system devices
System
Air Conditioner
Furnace
1a
Thermostat
Humiditrol
System
3rd Stage Delay
4th Stage Delay
Lock In 2nd Stage HP by Outdoor Temp
Balance Point Control
2a
Humiditrol Comfort Adjust
Min De-humidification Setpoint
Humiditrol Comfort Adjust
Select one
Maximum Overcooling
Minimum Overcooling
3a
save
3b
Humiditrol Comfort Adjust settings are
only available on units equipped with
®
a Humiditrol
De-humidification
device.
DE-HUMIDIFICATION SETTINGS — FEATURE SCREEN
1. From the Main Screen, press the right arrow icon to go the the Features
screen.
2. From the Features screen, select system settings.
3. Touch the button of the De-humidification settings you want to adjust; if it says
de-humidifier OFF, one touch will display a selection for OFF, MEDIUM or
HIGH.
4. Selecting MEDIUM or HIGH will bring on the set-to button.
5. When you touch the set-to button, the arrows appear, allowing you to change
to the desired de-humidifier percentage setting
507152-01
To adjust a setting,
highlight it,
about
then press Edit
System
resetAll
1b
edit
De-humidification Control Mode
reinstall
current value:
Midpoint Overcooling
reset
2b
edit
Midpoint Overcooling
back
System
Staged Delay TImers
cancel
2nd Stage Delay
3rd Stage Delay
4th Stage Delay
Lock In 2nd Stage HP by Outdoor Temp
Balance Point Control
Humiditrol Comfort Adjust
Min De-humidification Setpoint
OD/Humid Boundary
Outdoor Temperature Reading Calibr
9:39 am Aug 15, 2012
Figure 12. Adjust a Non-Communicating Device Setting — De-humidification
Pre-adjustment REQUIREMENTS:
1st, the device has been installed
2nd, from the "Add or Remove Non-communicating equipment?", press next.
3rd, in the "Adjust a setting..." screen, configure the device as follows:
1.In the "system devices" list, use the arrows (1a) to highlight System. Press
edit (1b).
®
2.Humiditrol
only—In the "System" list, use the arrows (2a) to highlight Humi
ditrol Comfort Adjust. The current value defaults to Maximum Overcooling.
Press edit (2b).
®
3.Humiditrol
only—Touch one of the radio buttons (3a) to select the overcool
ing level; press save (3b). (After saving, check that the current value now
shows the new selection).
4.Use arrows (4a) to highlight Min De-humidification Setpoint; press edit (4b).
Note the current value (e.g. 45).
5.Use arrows (5a) to make changes; press save (5b). (After saving, check that
the current value now shows the new selection).
6.Press the back button to return to "Adjust a setting..." screen.
De-humidification Control Mode
current value:
45
4a
edit
reset
6
(returns to
back
SYSTEM SETTINGS
humidifier
is ON
ALL CHANGES MADE ON
THIS SCREEN ARE IN
STANTLY SAVED.
Wi-Fi
9:39 am Aug 15, 2012
Figure 13. Humidifier Controls (Non-Communicating Outdoor Unit)
Page 12
Min De-humidification
Setpoint
4b
Range is 40 to 60
Default is 45, inc:1
set-to
5a
42
5b
save
cancel
adjust a
setting
screen)
humidification
De-humidification
settings
OFF
%
de-
40
humidifier
MEDIUM
MEDIUM
set to
HIGH
current indoor humidity is 50%
settings
humidifier
%
50
display
is ON
set to
(default is ON)
?
7/2013
Advertisement
Table of Contents
