Page 1 Service and Repair Manual Serial Number Range -2669 ™ from GS6911-101 This manual includes: from GS6916F-7897 Repair procedures to GS6916F-10499 -3369 ™ from GS69F-10500 Fault Codes Electrical and -4069 ™ Hydraulic Schematics For detailed maintenance procedures, refer to the appropriate Maintenance Manual for your machine.
Page 2: Introduction
Copyright © 2016 by Terex Corporation 1272219GT Rev B, May 2018 First Edition, First Printing Genie is a registered trademark of Terex South Dakota, Inc. in the U.S.A. and many other countries. “GS” is a trademark of Terex South Dakota, Inc.
Page 3: Revision History
May 2018 Service and Repair Manual Introduction Revision History Revision Date Section Procedure / Page / Description 3/2016 Initial Release 6/2016 Fault Codes Update fault codes 9/2016 Introduction Serial Number Legend 5/2017 Fault Codes Update fault codes 5/2018 All Sections Add GM .998L Engine information and schematics Repair 11-6 Oscillating Axle...
Page 4 Service and Repair Manual May 2018 Introduction Revision History (continued) Revision Date Section Procedure / Page / Description Reference Examples: Electronic Version Section – Repair Procedure, 4-2 Click on any content or procedure in the Table of Contents to view Section –...
Page 5: Serial Number Legend
May 2018 Service and Repair Manual Introduction Serial Number Legend To August 31, 2016 1 Model 4 Sequence number 2 Model year 5 Serial label (located inside cover) 3 Facility code 6 Serial number (stamped on chassis) From September 1, 2016 1 Model 4 Serial label (located inside cover) 2 Facility code...
Page 6: Safety Rules
Service and Repair Manual May 2018 Safety Rules Section 1 Safety R ules Danger Failure to obey the instructions and safety rules in this manual and the appropriate Operator's Manual on your machine will result in death or serious injury. Many of the hazards identified in the operator's manual are also safety hazards when maintenance and repair procedures are performed.
Page 7 May 2018 Service and Repair Manual Safety Rules Personal Safety Workplace Safety Any person working on or around a machine must Any person working on or around a machine must be aware of all known safety hazards. Personal be aware of all known safety hazards. Personal safety and the continued safe operation of the safety and the continued safe operation of the machine should be your top priority.
Page 8: Table Of Contents
May 2018 Table of Contents Introduction Introduction ......................ii Important Information ..................... ii Find a Manual for this Model .................. ii Revision History ..................... iii Serial Number Legend .................... v Section 1 Safety Rules ......................vi General Safety Rules .................... vi Section 2 Specifications .......................
Page 9 Platform Components ..................17 2-1 Platform ......................17 2-2 Platform Extension Deck ................18 Scissor Components ..................20 3-1 Scissor Assembly, GS-2669 RT ..............21 3-2 Scissor Assembly, GS-3369 RT ..............24 3-3 Scissor Assembly, GS-4069 RT ..............28 3-4 Wear Pads...................... 31 3-5 Lift Cylinders....................
Page 10 May 2018 Table of Contents Perkins 403D-11 Engine ..................43 6-1 Timing Adjustment ..................43 6-2 Flex Plate......................43 6-3 Coolant Temperature and Oil Pressure Switches .......... 43 6-4 Engine RPM ....................44 6-5 How to Repair the Perkins 403D-11 Engine ..........45 GM .998L Engine ....................
Page 11 May 2018 Table of Contents Manifolds ......................64 9-1 Function Manifold Components ..............64 9-2 Valve Adjustments - Function Manifold ............66 How to Adjust the System Relief Valve ............66 How to Adjust the Oscillate Relief Valve ............67 How to Adjust the Platform Up Relief Valve - Models with Platform Overload68 How to Adjust the Platform Up Relief Valve - Models without Platform Overload .........................
Page 12 May 2018 Table of Contents Outrigger Components ..................92 13-1 Outrigger Cylinder ..................92 Platform Overload Components ............... 93 14-1 Platform Overload System ................93 Platform Overload TroubleShooting ..............96 14-2 Platform Overload Recovery Message (software version B3 and later) ..97 Section 4 Fault Codes ......................
Page 13 Control Panel Circuit Diagram (to serial number GS6914-6018) ....... 128 Control Panel Circuit Diagram (from serial number GS6914-6019) ....129 Electrical Schematics - GS-2669 RT, GS3369RT (ANSI / CSA) ....131 Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) Kubota WG-972 Models (to serial number GS6915-6383) ......
Page 14 May 2018 Table of Contents Electrical Schematics - GS-2669 RT, GS3369RT (AS / CE) ......159 Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Kubota WG-972 Models (to serial number GS6915-6383) ......160 Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Kubota WG-972 Models (from serial number GS6915-6384 to GS6916F-9067) ..................
Page 15 Electrical Schematic, GS-4069 RT, (AS / CE) Diesel Models (from serial number GS6916F-9068) ........240 Hydraulic Schematics ..................243 Hydraulic Schematic, GS-2669 RT and GS-3369 RT (to serial number GS6915-6383) ..............244 Hydraulic Schematic, GS-2669 RT and GS-3369 RT (from serial number GS6915-6384) ............245 Hydraulic Schematic, GS-4069 RT (to serial number GS6915-6383) ....
Page 16: Specifications
May 2018 Service and Repair Manual Specifications Section 2 Specific ati ons Machine Specifications Castle nut (steer end) Castle nut torque, dry 300 ft-lbs Fluid capacities 406 Nm Hydraulic tank 16.5 gallons Castle nut torque, lubricated 225 ft-lbs (maximum fill capacity) 62.5 liters 305 Nm Hydraulic system (including tank)
Page 17: Performance Specifications
Hydraulic Oil Specifications Drive speed, maximum Hydraulic Fluid Specifications Platform stowed 3.5 mph Genie specifications require hydraulic oils which are High speed 5.6 km/h designed to give maximum protection to hydraulic 40 ft / 7.8 sec systems, have the ability to perform over a wide 12.2 m / 7.8 sec...
Page 18 May 2018 Service and Repair Manual Specifications Chevron Rando HD Premium Oil Do not top off with incompatible hydraulic fluids. Hydraulic fluids MV Fluid Properties may be incompatible due to the differences in base additive ISO Grade chemistry. When incompatible Viscosity index fluids are mixed, insoluble materials may form and deposit...
Page 19 Service and Repair Manual May 2018 Specifications Chevron 5606A Hydraulic Oil Petro-Canada Environ MV 46 Fluid Properties Fluid Properties ISO Grade ISO Grade Viscosity index Viscosity index Kinematic Viscosity Kinematic Viscosity cSt @ 200°F / 100°C cSt @ 200°F / 100°C cSt @ 104°F / 40°C 15.0 cSt @ 104°F / 40°C...
Page 20 May 2018 Service and Repair Manual Specifications UCON Hydrolube HP-5046 Fluid Properties ISO Grade Viscosity index Kinematic Viscosity cSt @ 149°F / 65°C cSt @ 104°F / 40°C cSt @ 0°F / -18°C 1300 Flash point None Pour point -81°F / -63°C Maximum continuous operating 189°F / 87°C temperature...
Page 21: Hydraulic Component Specifications
25 psi / 1.7 bar bypass Function manifold System relief valve pressure, 3500 psi maximum 241 bar Lift relief valve pressure 3100 psi GS-2669 RT 214 bar Lift relief valve pressure 2900 psi GS-3369 RT 200 bar Lift relief valve pressure 2850 psi...
Page 22: Gm Engine Models
May 2018 Service and Repair Manual Specifications GM Engine Models .998L Low idle 1100 rpm 36.6 Hz High idle 3000 rpm 100 Hz Oil capacity (including filter) 3.2 quarts 3.0 liters Engine coolant capacity 5 quarts 4.7 liters Spark plug gap 0.039 to 0.047 inches 1.0 to 1.2 mm Unit ships with 15W-40.
Page 23: Kubota D1105-E3B Engine Specifications
Service and Repair Manual May 2018 Specifications Kubota D1105-E3B Engine Fuel injection system Injection pump make Bosch MD 68.53 cu in Displacement Injection pump pressure, 1991 psi 1.123 liters maximum 137 bar Number of cylinders Injection timing 18° BTDC 3.07 x 3.09 inches Bore and Stroke Fuel requirement 78 x 78.4 mm...
Page 24: Kubota Wg-972 Engine Specifications
May 2018 Service and Repair Manual Specifications Kubota WG-972 Engine 40A @ 12V DC Alternator output Fan belt deflection 0.28 to 0.35 in 57.8 cu in Displacement 7 to 9 mm 0.96 liters Starter motor Number of cylinders Brush length, new 0.551 in 2.93 x 2.90 inches Bore and Stroke...
Page 25: Perkins 403D-11 Engine Specifications
Service and Repair Manual May 2018 Specifications Perkins 403D-11 Engine Unit ships with 15W-40. Extreme operating temperatures may require the use of alternative engine oils. For oil requirements, refer to the Engine Operator 69 cu in Displacement Manual for your engine. 1.13 liters Fuel injection system Number of cylinders...
Page 26: Hydraulic Hose And Fitting Torque Specifications
Your machine is equipped with Parker Seal-Lok™ SAE Dash Size Torque ORFS or 37° JIC fittings and hose ends. Genie 14 ft-lbs / 19 Nm specifications require that fittings and hose ends be torqued to specification when they are removed 23 ft-lbs / 31.2 Nm...
Page 27: Torque Procedure
Note: The O-ring in Parker Seal Lok™ fittings and hose end are custom-size O-rings. They are not standard size O-rings. They are available in the O-ring field service kit (Genie part number 49612). Lubricate the O-ring before installation. Be sure the O-ring face seal is seated and retained properly.
Page 28 May 2018 Service and Repair Manual Specifications Working clockwise on the body hex fitting, make a second mark with a permanent ink marker to indicate the proper tightening position. Refer to Illustration 2. Note: Use the JIC 37° Fitting table in this section to determine the correct number of flats, for the proper tightening position.
Page 29: Repair Procedures
 Be sure that all necessary tools and parts are available and ready for use.  Use only Genie approved replacement parts.  Read each procedure completely and adhere to the instructions. Attempting shortcuts may produce hazardous conditions.
Page 30 May 2018 Service and Repair Manual Repair Procedures About This Section Symbols Legend Safety alert symbol—used to alert Most of the procedures in this section should only personnel to potential personal be performed by trained service professional in a injury hazards. Obey all safety suitably equipped workshop.
Page 31: Platform Controls
LEDs. All of Controls Circuit Board these components are replaceable. For further information or assistance, consult Genie Push in the red Emergency Stop button to the Product Support. off position at both the ground and platform controls.
Page 32: Platform Components
May 2018 Service and Repair Manual Platform Components Remove the cover from the AC outlet. Tag and disconnect the wiring from the outlet. Platform Electrocution/burn hazard. Contact with electrically charged How to Remove the Platform circuits could result in death or serious injury.
Page 33: Platform Extension Deck
Service and Repair Manual May 2018 Platform Components Carefully lift the platform enough to clear the platform pivot. Platform Extension Deck 10 Slide the platform towards the non-steer end of the machine until the slider blocks are How to Remove the Platform visible underneath the slider block channel.
Page 34 May 2018 Service and Repair Manual Platform Components Release the four rail spacers by pulling the Carefully slide the platform extension out and retaining pin and turn them in a downward away from the platform and place it on a position.
Page 35: Scissor Components
Service and Repair Manual May 2018 Scissor Components Steer End Non-steer End 1 Platform pivot 10 Chassis pivot 2 Number 3 outer arm 11 Slider block (Qty. 2) 3 Lift cylinder rod-end pivot pin 12 Number 3 inner arm 4 Number 3 pivot pin (steer end) 13 Number 3 center pivot pin (Qty.
Page 36: Scissor Assembly, Gs-2669 Rt
Service and Repair Manual Scissor Components Using a suitable supporting device, attach a strap to the rod end of the lift cylinder. Do not Scissor Assembly, GS-2669 RT apply pressure. Remove the lift cylinder rod end pivot pin How to Disassemble the Scissor retaining fasteners.
Page 37 Service and Repair Manual May 2018 Scissor Components 13 Remove the retaining fasteners from the 20 Remove the two carriage bolts that secure the number 2 pivot pins. inner arm and chassis pivot to the steer end of the drive chassis. Note: Do not remove the external snap ring.
Page 38 May 2018 Service and Repair Manual Scissor Components Steer End Non-steer End 1 Platform pivot 13 Chassis pivot 2 Number 4 center pivot pin (Qty. 2) 14 Slider block (Qty. 2) 3 Number 4 pivot pin (steer end) 15 Number 4 inner arm 4 Number 3 center pivot pin (Qty.
Page 39: Scissor Assembly, Gs-3369 Rt
Service and Repair Manual May 2018 Scissor Components Using an overhead lifting device attach a 4 hook sling chain to the ends of the number 4 Scissor Assembly, GS-3369 RT inner arm. Make the chains tight but do not apply lifting pressure. How to Disassemble the Scissor Crushing hazard.
Page 40 May 2018 Service and Repair Manual Scissor Components 13 Remove the retaining fasteners from the 21 Tag and disconnect the hydraulic hoses from number 3 pivot pins. the lift cylinder. Plug the hoses and cap the fittings. Note: Do not remove the external snap ring. Bodily injury hazard.
Page 41 Service and Repair Manual May 2018 Scissor Components Separate the link sets: Using an overhead lifting device attach a 4 hook sling chain to the ends of the inner arm. Make the chains tight but do not apply lifting pressure. Crushing hazard.
Page 42 May 2018 Service and Repair Manual Scissor Components Steer End Non-steer End 1 Platform pivot 16 Slider block (Qty. 2) 2 Number 5 center pivot pin (Qty. 2) 17 Number 5 inner arm 3 Number 5 pivot pin (steer end) 18 Number 5 outer arm 4 Number 4 center pivot pin (Qty.
Page 43: Scissor Assembly, Gs-4069 Rt
Service and Repair Manual May 2018 Scissor Components Using an overhead lifting device attach a 4 hook sling chain to the ends of the number 4 Scissor Assembly, GS-4069 RT inner arm. Make the chains tight but do not apply lifting pressure. How to Disassemble the Scissor Crushing hazard.
Page 44 May 2018 Service and Repair Manual Scissor Components 13 Remove the retaining fasteners from the 22 Using a soft metal drift, remove the pivot pin. number 4 pivot pins. 23 Lower the lift cylinder and remove the strap. Note: Do not remove the external snap ring. 24 Using an overhead lifting device attach a 4 hook sling chain to the ends of the number 3 14 Using a soft metal drift, remove the pivot pins...
Page 45 Service and Repair Manual May 2018 Scissor Components Separate the link sets: 31 Carefully lift the linkage assembly off of the machine and place it on a structure capable of Using an overhead lifting device attach a 4 supporting it. hook sling chain to the ends of the inner arm.
Page 46: Wear Pads
May 2018 Service and Repair Manual Scissor Components Remove the fasteners securing the ladder to the chassis. Remove the ladder from the Wear Pads machine and set aside. Crushing hazard. The ladder How to Replace the Scissor Arm could fall if not properly Wear Pad supported when the fasteners are removed from the machine.
Page 47 Service and Repair Manual May 2018 Scissor Components Remove the retaining fasteners from the slider Using a hard rubber mallet, secure the upper feet pivot pins and set aside. and lower wear pads to the slider feet. 1 upper wear pads 1 Slider foot assembly 2 slider foot 2 pivot pin...
Page 48: Lift Cylinders
Scissor Components Lift Cylinders The lift cylinders are single acting hydraulic cylinders. The GS-2669 and GS-3369 uses one lift cylinder; the GS-4069 uses two. Each lift cylinder is equipped with a check valve to prevent movement in the event of a hydraulic line failure.
Page 49 Service and Repair Manual May 2018 Scissor Components Disassemble the scissor assembly. Refer to GS-4069 RT: Repair Procedure, How to Disassemble the Scissor Assembly. Bodily injury hazard. This procedure requires specific repair skills, lifting equipment and a suitable workshop. Attempting this procedure without these skills and tools could result in death or serious injury and significant...
Page 50: Kubota D1105 Engine
Kubota Workshop Manual. Connect the leads from an ohmmeter between Kubota - D1105 the far left glow plug and ground. Genie part number 229761 Result: The resistance should be approximately 1Ω. If the ohm reading is different than 1Ω, remove the wire and connector plate from the three individual glow plugs.
Page 51: Engine Rpm
Service and Repair Manual May 2018 Kubota D1105 Engine Move the engine idle control switch to high idle (rabbit symbol) from the ground controls. Engine RPM Hold the start toggle switch to the start position and check the engine RPM on the diagnostic How to Adjust the RPM display.
Page 52: Flex Plate
May 2018 Service and Repair Manual Kubota D1105 Engine How to Ins tall the Fl ex Plate How to Install the Flex Plate Flex Plate Install the flex plate onto the flywheel with the raised spline toward the pump. The flex plate couples the engine to the pump. The Note: Install the coupler onto the pump shaft flex plate is bolted to the engine flywheel and has a with the set screw towards the pump.
Page 53: Coolant Temperature And Oil Pressure Switches
Service and Repair Manual May 2018 Kubota D1105 Engine Tag and disconnect the wiring from the switch. Remove the switch from the engine. Coolant Temperature and Oil Pressure Switches The engine coolant temperature switch is a normally open switch. The switch contacts close at approximately 225°F / 107°C.
Page 54: How To Repair The Kubota D1105 Engine
How to Repair the Kubota D1105 Engine Repair procedures and additional engine information are available in the Kubota Operator's and Workshop Manuals. Kubota - D1105 Operator's Manual Genie part number 131379 Kubota - D1105 Workshop Manual Genie part number 229761 Part No. 1272219 ™...
Page 55: Kubota Wg972 Engine
Service and Repair Manual May 2018 Kubota WG972 Engine Choke Adjustment Timing Adjustment The choke is solenoid-operated and functions only The ignition timing cannot be adjusted. The timing in the gasoline mode. The choke will not operate in adjustment screw is factory sealed with a tamper LPG mode.
Page 56: Engine Rpm
May 2018 Service and Repair Manual Kubota WG972 Engine To correct the low idle speed, Loosen the core clamp screw so the cable moves freely. Engine RPM How to Adjust the RPM Note: The on-board self diagnostics incorporate a built-in engine tachometer. The engine rpm is displayed on the diagnostic display when the start button is held to the start position with the engine running.
Page 57: How To Repair The Kubota Wg972 Engine
Do not tighten. Hold the throttle lever against the low idle Kubota - WG972 Operator's Manual adjustment screw and turn the adjustment Genie part number 234803 screw clockwise to increase rpm or Kubota - WG972 Workshop Manual counterclockwise to decrease rpm.
Page 58: Perkins 403D-11 Engine
The switch contacts close at Perkins 403D-11 Workshop Manual approximately 221°F / 105°C. If the coolant Genie part number 131662 temperature rises above the switch point, the switch contacts close and the engine will shut off to prevent damage.
Page 59: Engine Rpm
Service and Repair Manual May 2018 Perkins 403D-11 Engine Coolant temperature switch: Tag and disconnect the wiring from the switch, located Engine RPM at the engine coolant outlet just above the alternator. Remove the switch from the engine. How to Adjust the RPM Oil Pressure switch: Tag and disconnect the Start the engine from the ground controls.
Page 60: How To Repair The Perkins 403D-11 Engine
To correct the high idle speed, loosen the yoke lock nut on the high idle solenoid, then turn the Perkins - 403D-11 Operator's Manual high idle adjustment nut and solenoid boot Genie part number 131661 counterclockwise to increase the rpm or clockwise to decrease the rpm. Tighten the Perkins - 403D-11 Workshop Manual yoke lock nut and recheck the rpm.
Page 61: Gm .998L Engine
Complete information to perform this procedure is available in the GM .998L Workshop Manual. GM .998L Workshop Manual Genie part number 1280320GT Flex Plate The flex plate acts as a coupler between the engine and the pump. It is bolted to the engine...
Page 62: Ground Controls
• High torque drive speed • Raised drive speed • Platform lift speed For further information or assistance, contact Genie Product Support. Tip-over hazard. Do not adjust the lift and/or drive speed higher than specified in this procedure. Setting drive speed greater than...
Page 63: How To Determine The Revision Level
Service and Repair Manual May 2018 Ground Controls How to D etermine the R evision Level How to Determine the Revision Press the lift function enable button. Level Press the yellow platform down button to decrease the drive speed or press the blue Turn the key switch to ground control and pull platform up button to increase the drive speed.
Page 64: How To Adjust The High Torque Drive Speed
May 2018 Service and Repair Manual Ground Controls How to Adj ust the High T orque Drive Speed How to Adjust the Stowed High Press the yellow platform down button to decrease the drive speed or press the blue Torque Drive Speed platform up button to increase the drive speed.
Page 65: How To Adjust The Raised Drive Speed
Service and Repair Manual May 2018 Ground Controls How to Adj ust the Rais ed Drive Speed How to Adjust the Raised Drive Press the yellow platform down button to decrease the drive speed or press the blue Speed platform up button to increase the drive speed. Refer to Specifications, Performance Tip-over hazard.
Page 66: How To Adjust The Lift Speed
May 2018 Service and Repair Manual Ground Controls How to Adj ust the Lift Speed How to Adjust the Lift Speed Press the lift function enable button. Tip-over hazard. Do not adjust the lift and/or drive speed higher than specified in this procedure. Setting drive speed greater than specifications could cause the machine to tip over resulting in...
Page 67: Software Configuration
Service and Repair Manual May 2018 Ground Controls ANSI and CSA models: Software Configuration Turn the key switch to ground control and pull out the red Emergency Stop button to the on position at both ground and platform controls. How to Configure the Software Result: The revision level of the ECM will The Electronic Control Module (ECM) contains appear in the LED display window.
Page 68 May 2018 Service and Repair Manual Ground Controls Press the lift function enable button. Models with platform overload (option): Use the yellow platform down arrow to scroll to Result: DESCENT DELAY is showing in the overload. diagnostic display window. Press the lift function enable button to activate or Result: OVERLOAD ON is showing in the deactivate the descent delay option.
Page 69: Level Sensor - Models Without Outriggers
Service and Repair Manual May 2018 Ground Controls 11 Use the yellow platform down arrow to scroll to generator option. Level Sensor - Models without Result: GENERATOR ON is showing in the Outriggers diagnostic display window. Press the lift function enable button to activate or The Electronic Control Module (ECM) is deactivate the generator option.
Page 70 May 2018 Service and Repair Manual Ground Controls Locate the level sensor in the ground controls compartment. 1 ground control box 2 level sensor 1 "Y" indicator 2 level sensor Tag and disconnect the wire harness from the level sensor. 3 "X"...
Page 71 Service and Repair Manual May 2018 Ground Controls Center a lifting jack under the drive chassis at 21 Models with RT tires: Place a 2.15 x 10 x 10 the ground controls side of the machine. inch / 5.46 x 25 x 25 cm thick steel block under both wheels at the ground controls side of the 10 Raise the machine approximately 4 inches / machine.
Page 72: Level Sensor - Models With Outriggers
May 2018 Service and Repair Manual Ground Controls Locate the level sensor in the ground controls compartment. Level Sensor - Models with Outriggers The Electronic Control Module (ECM) is programmed to deactivate the lift and drive functions and activate an alarm when a signal is received from the level sensor.
Page 73 Service and Repair Manual May 2018 Ground Controls Install the new level sensor onto the machine Connect the wire harness to the level sensor. with the "X" on the level sensor base towards Turn the key switch to platform controls and the steer end of the machine.
Page 74 May 2018 Service and Repair Manual Ground Controls Adjust the front-to-back axis: Confirm the side-to-side level sensor setting: 13 Without disconnecting the wire harness from 20 Center a lifting jack under the drive chassis at the level sensor, connect the positive lead of the ground controls side of the machine.
Page 75 Service and Repair Manual May 2018 Ground Controls 30 Raise the machine approximately 6 inches / 40 Lower the machine onto the blocks. 15 cm. 41 Raise the platform approximately 12 feet / 3.6 31 Models with RT tires: Place a 2.15 x 10 x 10 inch / 5.46 x 25 x 25 cm thick steel block under Result: The platform stops raising and the tilt both wheels at the ground controls side of the...
Page 76 May 2018 Service and Repair Manual Ground Controls 50 Raise the platform approximately 12 feet / 3.6 Result: The platform stops raising and the tilt alarm will sound at 180 beeps per minute. Result: The platform does not stop raising and the tilt alarm does not sound.
Page 77: Hydraulic Pump
Service and Repair Manual May 2018 Hydraulic Pump How to R emove the Hydr aulic Pump How to Remove the Hydraulic Pump Hydraulic Pump Tag, disconnect and plug the hydraulic hoses The hydraulic pump is a single section, gear-type on the pump. Cap the fittings on the pump. pump.
Page 78: How To Prime The Pump
May 2018 Service and Repair Manual Hydraulic Pump How to Prime the Pum p How to Prime the Pump Component damage hazard. Be sure that the hydraulic tank shutoff valves are in the open position before priming the pump. The engine must not be started with the hydraulic tank shutoff valves in the closed position or component damage...
Page 79: Manifolds
Service and Repair Manual May 2018 Manifolds Function Manifold Components The function manifold is located inside the hydraulic tray. Index Schematic Description Function Torque Item Priority flow regulator,1 gpm / 3.8 L/min Oscillate circuit 25-30 ft-lbs / 34-41 Nm Solenoid valve, 2 position 2 way N.C. Oscillate float 25-30 ft-lbs / 34-41 Nm Relief valve, 3300 psi / 227.5 bar...
Page 80 May 2018 Service and Repair Manual Manifolds Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 81: Valve Adjustments - Function Manifold
Service and Repair Manual May 2018 Manifolds Adjust the internal hex socket. Turn it clockwise to increase the pressure or Valve Adjustments - counterclockwise to decrease the pressure. Function Manifold Install the relief valve cap. Tip-over hazard. Do not adjust How to Adj ust the Sy stem Reli ef Valve How to Adjust the System Relief the relief valve higher than...
Page 82: How To Adjust The Oscillate Relief Valve
May 2018 Service and Repair Manual Manifolds How to Adj ust the Oscill ate R elief Valve How to Adjust the Oscillate Relief Adjust the internal hex socket. Turn it clockwise to increase the pressure or Valve counterclockwise to decrease the pressure. Install the relief valve cap.
Page 83 Service and Repair Manual May 2018 Manifolds How to Adj ust the Pl atform U p R elief Valve - Models with Platform Ov erload How to Adjust the Platform Up Press the lift function enable button. Relief Valve - Models with Result: DESCENT DELAY is showing in the diagnostic display window.
Page 84 May 2018 Service and Repair Manual Manifolds 16 Locate and remove the maximum height limit 17 Locate and disconnect the lift cylinder switch from the lower slider channel and set pressure switch harness. aside. Note: Do not disconnect the limit switch harness. 1 solenoid valve (proportional lift models) 2 solenoid valve (2 speed lift models) 3 lift cylinder...
Page 85 Service and Repair Manual May 2018 Manifolds 24 Press and hold the lift function enable button 28 Lower the platform and remove the test and press and hold the blue platform up weights. button. Allow the platform to raise completely, 29 Raise the platform approximately 10 feet / 3 m.
Page 86: How To Adjust The Platform Up Relief Valve - Models Without Platform Overload
May 2018 Service and Repair Manual Manifolds How to Adj ust the Pl atform U p R elief Valve - Models without Pl atform Overl oad How to Adjust the Platform Up 40 Press the lift function enable button. Relief Valve - Models without Result: DESCENT DELAY is showing in the diagnostic display window.
Page 87 Service and Repair Manual May 2018 Manifolds Adjust the internal hex socket. Turn it clockwise to increase the pressure or counterclockwise to decrease the pressure. Install the relief valve cap. Tip-over hazard. Failure to adjust the relief valve as instructed will cause the machine to tip over resulting in death or serious injury.
Page 88: Outrigger Manifold Components
May 2018 Service and Repair Manual Manifolds Outrigger Manifold Components The outrigger manifold is located beneath the hose cover panel on top of the drive chassis Index Schematic Description Function Torque Item Solenoid valve, 3 position 4 way NC Outriggers in / out 40 ft-lbs / 54 Nm Part No.
Page 89: Traction Manifold Components - View 1
Service and Repair Manual May 2018 Manifolds Traction Manifold Components - View 1 The traction manifold is located inside the hydraulic tray. Index Schematic Description Function Torque Item Solenoid Valve, 2 position 3 way Brake release 40 ft-lbs / 54 Nm Solenoid valve, 2 position 4 way Front motor isolate 50 ft-lbs / 68 Nm...
Page 90 May 2018 Service and Repair Manual Manifolds Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 91: Traction Manifold Components - View 2
Service and Repair Manual May 2018 Manifolds Traction Manifold Components - View 2 The traction manifold is located inside the hydraulic tray. Index Schematic Description Function Torque Item Orifice, 0.030 inch / .76 mm Brake circuit Orifice, 0.030 inch / .76 mm Two speed circuit Pressure reducing valve, Two-speed and brake circuit...
Page 92 May 2018 Service and Repair Manual Manifolds Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 93: Generator Manifold Components
Service and Repair Manual May 2018 Manifolds Generator Manifold Components The generator manifold is located above the function manifold. Index Schematic Description Function Torque Item Proportional solenoid valve Generator speed 33-37 ft-lbs / 45-50 Nm Relief valve, 2700 psi / 186 bar Generator circuit 20-25 ft-lbs / 27-34 Nm ™...
Page 94: Valve Coils
May 2018 Service and Repair Manual Manifolds Valve Coil Resistance Specification Valve Coils Note: The following coil resistance specifications How to Test a Coil are at an ambient temperature of 68°F / 20°C. As valve coil resistance is sensitive to changes in air A properly functioning coil provides an temperature, the coil resistance will typically electromotive force which operates the solenoid...
Page 95 6. Resistor 10Ω Set a multimeter to read DC current. Genie part number 27287 Note: The multimeter, when set to read DC current, Note: The battery should read 9V DC or more when should be capable of reading up to 800 mA.
Page 96: How To Test The Coils Using The Test System Function
May 2018 Service and Repair Manual Manifolds How to T est the Coils Using the T est Sys tem Func tion How to Test the Coils Using the Use the yellow platform down arrow to scroll to test system. Test System Function Result: TEST SYSTEM is showing in the The Electronic Control Module (ECM) contains diagnostic display window.
Page 97: Fuel And Hydraulic Tanks
Service and Repair Manual May 2018 Fuel and Hydraulic Tanks 10-1 Loosen the fuel tank mounting strap fastener. Pull the tank strap to the side. Fuel Tank Note: Do not remove the tank strap. How to Remove the Fuel Tank Remove the fuel tank from the machine.
Page 98: Hydraulic Tank
May 2018 Service and Repair Manual Fuel and Hydraulic Tanks 10-2 Tag and disconnect the harnesses from the ground control box. Hydraulic Tank Remove the ground control box from the The primary functions of the hydraulic tank is to machine and set aside. cool, clean and deaerate the hydraulic fluid during Tag, disconnect and plug the hydraulic hoses operation.
Page 99: Steer Axle Components
Service and Repair Manual May 2018 Steer Axle Components 11-1 Tag, disconnect and plug the hoses from the drive motor. Cap the fittings on the drive Yoke and Drive Motor motor. Bodily injury hazard. Spraying How to Remove the Yoke and hydraulic oil can penetrate and Drive Motor burn skin.
Page 100: How To Remove A Drive Motor
May 2018 Service and Repair Manual Steer Axle Components How to R emove a Drive M otor How to Remove a Drive Motor 11-2 Steer Cylinder Component damage hazard. Repairs to the motor should only be performed by an authorized How to Remove the Steer dealer.
Page 101: Tie Rod
Service and Repair Manual May 2018 Steer Axle Components 11-3 11-4 Tie Rod Oscillate Cylinder How to Remove the Tie Rod How to Remove the Oscillate Cylinder Remove the rue ring from each tie rod clevis pin. Remove the clevis pins. Note: When removing a hose assembly or fitting, the O-ring (if equipped) on the fitting and/or hose Remove the tie rod.
Page 102: Oscillate Hoses
May 2018 Service and Repair Manual Steer Axle Components 11-5 Tag and disconnect the connector with the red wire from the oscillate left coil (item A) and the Oscillate Hoses connector with the white wire from the oscillate right coil (item B) and set aside. Refer to Test the Oscillate Axle Hose illustration 2.
Page 103 Service and Repair Manual May 2018 Steer Axle Components Check the Steering Slowly drive the machine in a safe direction and activate steer right. Turn the key switch to platform control and pull Result: The right oscillate cylinder will extend out the red Emergency Stop button to the on and the left oscillate cylinder will retract.
Page 104: Oscillating Axle
May 2018 Service and Repair Manual Steer Axle Components 11-6 Oscillate Limit Switches LSALOS, LSALOO Oscillating Axle When elevated and driving if load is removed from the left rear wheel, LSALOS changes state interrupting power to the ECM (U5), connector How the Oscillating Axle J2-A8 and sends 12V input power to the right oscillate valve Y94.
Page 105: Non-Steer Axle Components
Service and Repair Manual May 2018 Non-steer Axle Components 12-1 Remove the drive motor / brake mounting fasteners. Drive Motor / Brake Assembly Remove the drive motor / brake assembly from the drive hub and remove from the How to Remove a Drive Motor / machine.
Page 106: Drive Hub
May 2018 Service and Repair Manual Non-steer Axle Components 12-2 Raise the machine approximately 2 inches / 5 cm. Place blocks under the chassis for Drive Hub support. Crushing hazard. The chassis How to Remove a Drive Hub will fall if not properly supported. Component damage hazard.
Page 107: Outrigger Components
Service and Repair Manual May 2018 Outrigger Components 13-1 Attach a lifting strap from an overhead crane to the barrel end of the outrigger cylinder for Outrigger Cylinder support. Do not apply any lifting pressure. Remove the outrigger mounting fasteners. How to Remove an Outrigger Slide the outrigger cylinder down and away Cylinder (if equipped)
Page 108: Platform Overload Components
Machines with platform overload systems, proper of the platform deck. calibration is essential to safe machine operation. GS-2669 1500 lb An improperly calibrated platform overload system 680 kg could result in the system failing to sense an overloaded platform.
Page 109 Service and Repair Manual May 2018 Platform Overload Components 14 Using a small slotted screwdriver, turn the 17 Remove the supporting device from under the adjustment screw of the platform overload platform. pressure switch one-quarter turn into the 18 Raise the platform to 13 ft / 4 m. hydraulic line.
Page 110 Remove the test weight. Switch Using a suitable lifting device, place a test weight in the center of the platform floor. Secure the weight to the platform. Refer to the chart below. GS-2669 1500 lb 680 kg GS-3369 1000 lb 454 kg...
Page 111: Platform Overload Troubleshooting
Service and Repair Manual May 2018 Platform Overload Components Platform Ov erload Troubl eShooti ng Platform Overload System Troubleshooting Condition Possible Cause Solution Cannot lift rated load Relief valve set too low Increase relief valve pressure At max. Height with rated load in platform, System needs to be reset Turn off red emergency stop button, pressure switch alarm continues to sound...
Page 112: Platform Overload Recovery Message (Software Version B3 And Later)
May 2018 Service and Repair Manual Platform Overload Components 14-2 Use the down button to scroll to select options. Platform Overload Recovery Press the function enable button. Message (software version B3 Result: DESCENT DELAY is showing in the and later) LCD screen.
Page 113: Fault Codes
Service and Repair Manual May 2018 Fault Codes Section 4 Faul t Codes Before Troubleshooting:  Read, understand and obey the safety rules and operating instructions in the appropriate operator's manual on your machine.  Be sure that all necessary tools and test equipment are available and ready for use.
Page 114 May 2018 Service and Repair Manual Fault Codes About This Section LED Diagnostic Readout When a malfunction is discovered, the fault code charts in this section will help a service professional pinpoint the cause of the problem. To use this section, basic hand tools and certain pieces of test equipment are required —...
Page 115 Service and Repair Manual May 2018 Fault Codes System Ready LED Condition Result Solution INTERNAL ECU Internal ECM error. System shutdown. Replace ECM. FAULT PLATFORM ECU Platform/ECM System shutdown. Troubleshoot control cable OR FAULT communication error. troubleshoot platform controls. CHASSIS START Engine start button fault at Engine will not Replace ECM.
Page 116 May 2018 Service and Repair Manual Fault Codes System Ready LED Condition Result Solution PLATFORM Engine start button fault at Engine will not start. Troubleshoot button OR START SW platform controls. replace printed circuit board FAULT at platform controls. LEFT FRONT Left front outrigger enable Outriggers disabled.
Page 117 Service and Repair Manual May 2018 Fault Codes System Ready LED Condition Result Solution DRIVE COIL 2 Drive coil 2 (Y1A) fault. High speed drive Troubleshoot coil OR wiring. FAULT function will not operate. DRIVE COIL 3 Drive coil 3 (Y1B) fault. High speed drive Troubleshoot coil OR wiring.
Page 118 LOW ECU Low ECM voltage. System shutdown. Charge battery. VOLTAGE LOW ENGINE Low RPM. Engine idle RPM too Contact Genie Product low. Support. HIGH ENGINE High RPM. Engine RPM too Contact Genie Product high. Support. LEFT FRONT...
Page 119: How To Retrieve Engine Fault - Codes Gm .998L Models
Service and Repair Manual May 2018 Fault Codes How to Retrieve Engine Fault Codes - GM .998L Models The emissions control system utilizes a diagnostic display located on the ground control box. A fault condition will be displayed for one of the following: The fault caused the engine to shut down or the fault is related to the exhaust gas oxygen (EGO) sensors.
Page 120: Gm Fault Codes
May 2018 Service and Repair Manual Fault Codes GM Fault Code Chart DTC Set 2 DTC Set 2 Description Description SPN-2/FMI-2 SPN-2/FMI-2 DTC 11: Intake cam / distributor position error 520800 / 7 DTC 221: TPS1-2 higher than expected 653/6 DTC 16: Crank and/or cam no sync during start 636 / 8 DTC 222: TPS2 voltage low...
Page 121 Service and Repair Manual May 2018 Fault Codes GM Fault Code Chart DTC Set 2 DTC Set 2 Description Description SPN-2 / FMI-2 SPN-2 / FMI-2 DTC 420: Catalyst inactive on gasoline (Bank 1) 520211 / 10 DTC 1111: RPM above fuel rev limit level 515 / 16 DTC 430: Catalyst inactive on gasoline (Bank 2) 520212 / 10 DTC 1112: RPM above spark rev limit level 515 / 0...
Page 122 May 2018 Service and Repair Manual Fault Codes GM Fault Code Chart DTC Set 2 DTC Set 2 Description Description SPN-2 / FMI-2 SPN-2 / FMI-2 DTC 1315: Cylinder 5 misfire detected 1327 / 11 DTC 1543: AUX analog Pull-Up/Down 2 high voltage 520220 / 3 DTC 1316: Cylinder 6 misfire detected 1328 / 11...
Page 123 Service and Repair Manual May 2018 Fault Codes GM Fault Code Chart DTC Set 2 DTC Set 2 Description Description SPN-2 / FMI-2 SPN-2 / FMI-2 DTC 1541: AUX analog Pull-Up/Down 1 high DTC 1632: PWM1-Gauge1 short to power 520219 / 3 697 / 6 voltage DTC 1542: AUX analog Pull-Up/Down 1 low...
Page 124 May 2018 Service and Repair Manual Fault Codes GM Fault Code Chart DTC Set 2 DTC Set 2 Description Description SPN-2 / FMI-2 SPN-2 / FMI-2 DTC 2123: FPP1 voltage low 91 / 4 DTC 2328: Spark coil 10 primary shorted 1277 / 6 DTC 2125: FPP2 invalid voltage and FPP1 520250 / 31 DTC 2428: EGT temperature high...
Page 125: Schematics
Service and Repair Manual May 2018 Schematics Section 5 About This Section Schem atics There are two groups of schematics in this section. Electrical Schematics Electrocution/burn hazard. Contact with electrically charged Observe and Obey: circuits could result in death or serious injury.
Page 126: Electrical Component And Wire Color Legends
May 2018 Service and Repair Manual Electrical Component and Wire Color Legends Item Description Item Description Battery Control relay Engine start Button Ignition power Engine start Engine start (platform) High idle Glow plug (Diesel models) (platform) Horn Choke (Gas/LPG models) (platform) Oscillate float enable High idle (platform) CR10...
Page 127 Service and Repair Manual May 2018 Electrical Component and Wire Color Legends Item Description Item Description Gauge Motor or Pump Hour meter Oil cooler (option) Diagnostic display Starter Fuel pump (Gas / LPG models) Horn or alarm Level sensor alarm (platform) Red emergency stop button Horn Ground control...
Page 128 May 2018 Service and Repair Manual Electrical Component and Wire Color Legends Item Description Color Description Terminal base (Ground controls terminal Blue strip) Black Toggle switch Brown TS18 Work light (option) Green Electronic Component Orange Circuit board (platform) Purple ECU (Electronic control unit) Ignition coil (Gas/LPG models) White Spark plugs (Gas/LPG models)
Page 129: Hydraulic Component Legend
Service and Repair Manual May 2018 Hydraulic Component Legend Item Function Item Function 3 position, 4 way directional valve - outrigger 2 position, 3 way valve - brake release cylinders extend/retract 2 position, 4 way valve - blocks flow to the Proportional valve - controls flow to the steer motors in high drive generator (option)
Page 130: Electrical Symbols Legend
May 2018 Service and Repair Manual Electrical Symbols Legend Battery Motor Horn or alarm Flashing beacon Gauge Circuit breaker with Diode Coil with suppression Fuse with amperage amperage Level sensor Connection - no Circuits crossing no Quick disconnect Power relay terminal connection terminal...
Page 131: Hydraulic Symbols Legend
Service and Repair Manual May 2018 Hydraulic Symbols Legend Orifice with size Check valve Cylinder, double acting Accumulator Pump, prime mover (engine Pump, fixed displacement Pressure switch Needle valve or motor) Solenoid operated 3 Solenoid operated Solenoid operated 2 Solenoid operated 2 position 4 way directional 3 position 5 way position, 3 way directional...
Page 132: Limit Switch Legend
May 2018 Service and Repair Manual Limit Switch Legend 1 left rear outrigger limit switch, LS14 6 right front outrigger limit switch, LS13 left front outrigger limit switch, LS12 (not 2 left axle oscillate limit switches, LSA10S shown) and LSA10SS 7 platform down limit switches, LS6 and 3 right rear outrigger limit switch, LS15 LS6B...
Page 133: Electronic Control Module Pin-Out Legend
Service and Repair Manual May 2018 Electronic Control Module Pin-Out Legend Electronic Control Unit Pin Numbering - 36 pin connector ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 134 May 2018 Service and Repair Manual Electronic Control Module Pin-Out Legend J1 Connector J2 Connector Right turn Y3 (output) Not used Left turn Y4 (output) Down limit switch LS6 (input) Platform up Y8 output) (ANSI / CSA) Auxiliary down power (input) Brake Y2 (output) Auxiliary down relay CR72-86 (output) Drive forward 1 Y6 (output)
Page 135: Ground Control Box - Ansi / Csa Models
Service and Repair Manual May 2018 Ground Control Box - ANSI / CSA Models ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 136: Ground Control Box - As /Ce Models
May 2018 Service and Repair Manual Ground Control Box - AS /CE Models Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 137: Platform Control Box - All Models
Service and Repair Manual May 2018 Platform Control Box - All Models ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 138: Gm .998L Engine Fuse And Relay Layout
May 2018 Service and Repair Manual GM .998L Engine Fuse and Relay Layout Power Relay Fuel Pump, Fuse - 15A Fuel Pump Relay DEPR, Fuse - 5A Starter Relay ECM, Fuse - 10A Alternator, Fuse - 60A Ignition, Fuse - 20A Empty Starter, Fuse - 25A VSW, Fuse - 5A...
Page 139 Service and Repair Manual May 2018 This page intentionally left blank. ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 140: Gm .998L Engine Wire Harness
May 2018 Service and Repair Manual GM .998L Engine Wire Harness...
Page 141 Service and Repair Manual May 2018 GM .998L Engine Wire Harness ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 142: Control Panel Circuit Diagram (To Serial Number Gs6914-6018)
May 2018 Service and Repair Manual Control Panel Circuit Diagram (to serial number GS6914-6018)
Page 143 Service and Repair Manual May 2018 Control Panel Circuit Diagram (to serial number GS6914-6018) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 144: Control Panel Circuit Diagram (From Serial Number Gs6914-6019)
May 2018 Service and Repair Manual Control Panel Circuit Diagram (from serial number GS6914-6019) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 145 Service and Repair Manual May 2018 Control Panel Circuit Diagram (from serial number GS6914-6019)
Page 146: Kubota Wg-972 Models (To Serial Number Gs6915-6383)
May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) Kubota WG-972 Models (to serial number GS6915-6383)
Page 147: Electrical Schematic, Gs-2669 Rt And Gs-3369 Rt, (Ansi / Csa Kubota Wg-972 Models (To Serial Number Gs6915-6383)
Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) Kubota WG-972 Models (to serial number GS6915-6383) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 148: Electrical Schematic, Gs-2669 Rt And Gs-3369 Rt, (Ansi / Csa
May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) Kubota WG-972 Models (to serial number GS6915-6383) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 149 Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) Kubota WG-972 Models (to serial number GS6915-6383)
Page 150: Kubota Wg-972 Models (From Serial Number Gs6915-6384 To Gs6916F-9067)
May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) Kubota WG-972 Models (from serial number GS6915-6384 to GS6916F-9067)
Page 151: Kubota Wg-972 Models (From Serial Number Gs6915-6384 To Gs6916F-9067)
Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) Kubota WG-972 Models (from serial number GS6915-6384 to GS6916F-9067) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 152 May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) Kubota WG-972 Models (from serial number GS6915-6384 to GS-6916F-9067) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 153 Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) Kubota WG-972 Models (from serial number GS6915-6384 to GS6916F-9067)
Page 154: Kubota Wg-972 Models (From Serial Number Gs6916F-9068 To Gs6916F-9100)
May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) Kubota WG-972 Models (from serial number GS6916F-9068 to GS6916F-9100)
Page 155 Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) Kubota WG-972 Models (from serial number GS6916F-9068 to GS6916F-9100) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 156 May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) Kubota WG-972 Models (from serial number GS-6916F-9068 to GS6916F-9100) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 157 Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) Kubota WG-972 Models (from serial number GS6916F-9068 to GS6916F-9100)
Page 158: Gm .998L Models (From Serial Number Gs6916F-9101)
May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) GM .998L Models (from serial number GS6916F-9101)
Page 159: Electrical Schematic, Gs-2669 Rt And Gs-3369 Rt, (Ansi / Csa Gm .998L Models (From Serial Number Gs6916F-9101)
Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) GM .998L Models (from serial number GS6916F-9101) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 160 May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) GM .998L Models (from serial number GS6916F-9101) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 161 Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) GM .998L Models (from serial number GS6916F-9101)
Page 162: Electrical Schematic, Gs-2669 Rt And Gs-3369 Rt, (Ansi / Csa) Diesel Models (To Serial Number Gs6915-6383)
May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) Diesel Models (to serial number GS6915-6383)
Page 163 Service and Repair Manual May 2018 Electrical Schematic, (ANSI / CSA) GS-2669 RT and GS-3369 RT, Diesel Models (to serial number GS6915-6383) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 164 May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) Diesel Models (to serial number GS6915-6383) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 165 Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) Diesel Models (to serial number GS6915-6383)
Page 166: Diesel Models (From Serial Number Gs6915-6384 To Gs6916F-9067)
May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) Diesel Models (from serial number GS6915-6384 to GS6916F-9067)
Page 167: Electrical Schematic, Gs-2669 Rt And Gs-3369 Rt, (Ansi / Csa Diesel Models (From Serial Number Gs6915-6384 To Gs6916F-9067)
Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) Diesel Models (from serial number GS6915-6384 to GS6916F-9067) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 168 May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) Diesel Models (from serial number GS6915-6384 to GS6916F-9067) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 169 Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) Diesel Models (from serial number GS6915-6384 to GS6916F-9067)
Page 170: Diesel Models (From Serial Number Gs6916F-9068)
May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) Diesel Models (from serial number GS6916F-9068)
Page 171 Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) Diesel Models (from serial number GS6916F-9068) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 172 May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) Diesel Models (from serial number GS6916F-9068) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 173 Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (ANSI / CSA) Diesel Models (from serial number GS6916F-9068)
Page 174: Electrical Schematic, Gs-2669 Rt And Gs-3369 Rt, (As / Ce) Kubota Wg-972 Models (To Serial Number Gs6915-6383)
May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Kubota WG-972 Models (to serial number GS6915-6383)
Page 175 Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Kubota WG-972 Models (to serial number GS6915-6383) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 176: Electrical Schematic, Gs-2669 Rt And Gs-3369 Rt, (As / Ce
May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Kubota WG-972 Models (to serial number GS6915-6383) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 177 Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Kubota WG-972 Models (to serial number GS6915-6383)
Page 178: Electrical Schematic, Gs-2669 Rt And Gs-3369 Rt, (As / Ce) Kubota Wg-972 Models (From Serial Number Gs6915-6384 To Gs6916F-9067)
May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Kubota WG-972 Models (from serial number GS6915-6384 to GS6916F-9067)
Page 179: Kubota Wg-972 Models (From Serial Number Gs6915-6384 To Gs6916F-9067)
Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Kubota WG-972 Models (from serial number GS6915-6384 to GS6916F-9067) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 180 May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Kubota WG-972 Models (from serial number GS6915-6384 to GS6916F-9067) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 181 Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Kubota WG-972 Models (from serial number GS6915-6384 to GS6916F-9067)
Page 182: Electrical Schematic, Gs-2669 Rt And Gs-3369 Rt, (As / Ce) Kubota Wg-972 Models (From Serial Number Gs6916F-9068 To Gs6916F-9100)
May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Kubota WG-972 Models (from serial number GS6916F-9068 to GS6916F-9100)
Page 183 Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Kubota WG-972 Models (from serial number GS6916F-9068 to GS6916F-9100) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 184 May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Kubota WG-972 Models (to serial number GS6916F-9068 to GS6916F-9100) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 185 Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Kubota WG-972 Models (to serial number GS6916F-9068 to GS6916F-9100)
Page 186: Electrical Schematic, Gs-2669 Rt And Gs-3369 Rt, (As / Ce) Gm .998L Models (From Serial Number Gs6916F-9101)
May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) GM .998L Models (from serial number GS6916F-9101)
Page 187 Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) GM .998L Models (from serial number GS6916F-9101) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 188 May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) GM .998L Models (from serial number GS6916F-9101) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 189 Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) GM .998L Models (from serial number GS6916F-9101)
Page 190: Electrical Schematic, Gs-2669 Rt And Gs-3369 Rt, (As / Ce) Diesel Models (To Serial Number Gs6915-6383)
May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Diesel Models (to serial number GS6915-6383)
Page 191: Electrical Schematic, Gs-2669 Rt And Gs-3369 Rt, (As / Ce Diesel Models (To Serial Number Gs6915-6383)
Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Diesel Models (to serial number GS6915-6383) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 192 May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Diesel Models (to serial number GS6915-6383) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 193 Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Diesel Models (to serial number GS6915-6383)
Page 194: Electrical Schematic, Gs-2669 Rt And Gs-3369 Rt, As / Ce) Diesel Models (From Serial Number Gs6915-6384 To Gs6916F-9067)
May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Diesel Models (from serial number GS6915-6384 to GS6916F-9067)
Page 195: Electrical Schematic, Gs-2669 Rt And Gs-3369 Rt, As / Ce Diesel Models (From Serial Number Gs6915-6384 To Gs6916F-9067)
Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Diesel Models (from serial number GS6915-6384 to GS6916F-9067) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 196 May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Diesel Models (from serial number GS6915-6384 to GS6916F-9067) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 197 Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Diesel Models (from serial number GS6915-6384 to GS6916F-9067)
Page 198: Electrical Schematic, Gs-2669 Rt And Gs-3369 Rt, As / Ce) Diesel Models (From Serial Number Gs6916F-9068)
May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Diesel Models (from serial number GS6916F-9068)
Page 199 Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Diesel Models (from serial number GS6916F-9068) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 200 May 2018 Service and Repair Manual Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Diesel Models (from serial number GS6916F-9068) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 201 Service and Repair Manual May 2018 Electrical Schematic, GS-2669 RT and GS-3369 RT, (AS / CE) Diesel Models (from serial number GS6916F-9068)
Page 202: Electrical Schematic, Gs-4069 Rt, (Ansi / Csa) Kubota Wg-972 Models (To Serial Number Gs6915-6383)
May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (ANSI / CSA) Kubota WG-972 Models (to serial number GS6915-6383)
Page 203: Electrical Schematic, Gs-4069 Rt, (Ansi / Csa Kubota Wg-972 Models (To Serial Number Gs6915-6383)
Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (ANSI / CSA) Kubota WG-972 Models (to serial number GS6915-6383) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 204 May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (ANSI / CSA) Kubota WG-972 Models (to serial number GS6915-6383) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 205 Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (ANSI / CSA) Kubota WG-972 Models (to serial number GS6915-6383)
Page 206: Electrical Schematic, Gs-4069 Rt, (Ansi / Csa) Kubota Wg-972 Models (From Serial Number Gs6915-6384 To Gs6916F-9067)
May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (ANSI / CSA) Kubota WG-972 Models (from serial number GS6915-6384 to GS6916F-9067)
Page 207: Kubota Wg-972 Models (From Serial Number Gs6915-6384 To Gs6916F-9067)
Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (ANSI / CSA) Kubota WG-972 Models (from serial number GS6915-6384 to GS6916F-9067) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 208 May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (ANSI / CSA) Kubota WG-972 Models (from serial number GS6915-6384 to GS6916F-9067) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 209: Electrical Schematic, Gs-4069 Rt, (Ansi / Csa
Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (ANSI / CSA) Kubota WG-972 Models (from serial number GS6915-6384 to GS6916F-9067)
Page 210: Electrical Schematic, Gs-4069 Rt, (Ansi / Csa) Kubota Wg-972 Models (From Serial Number Gs6916F-9068 To Gs6916F-9100)
May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (ANSI / CSA) Kubota WG-972 Models (from serial number GS6916F-9068 to GS6916F-9100)
Page 211 Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (ANSI / CSA) Kubota WG-972 Models (from serial number GS6916F-9068 to GS6916F-9100) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 212 May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (ANSI / CSA) Kubota WG-972 Models (from serial number GS6916F-9068 to GS6916F-9100) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 213 Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (ANSI / CSA) Kubota WG-972 Models (from serial number GS6916F-9068 to GS6916F-9100)
Page 214: Electrical Schematic, Gs-4069 Rt, (Ansi / Csa) Gm .998L Models (From Serial Number Gs6916F-9101)
May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (ANSI / CSA) GM .998L Models (from serial number GS6916F-9101)
Page 215 Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (ANSI / CSA) GM .998L Models (from serial number GS6916F-9101) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 216 May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (ANSI / CSA) GM .998L Models (from serial number GS6916F-9101) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 217 Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (ANSI / CSA) GM .998L Models (from serial number GS6916F-9101)
Page 218: Electrical Schematic, Gs-4069 Rt, (Ansi / Csa) Diesel Models (To Serial Number Gs6915-6383)
May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (ANSI / CSA) Diesel Models (to serial number GS6915-6383)
Page 219 Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (ANSI / CSA) Diesel Models (to serial number GS6915-6383) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 220 May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (ANSI / CSA) Diesel Models (to serial number GS6915-6383) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 221 Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (ANSI / CSA) Diesel Models (to serial number GS6915-6383)
Page 222: Electrical Schematic, Gs-4069 Rt, (Ansi / Csa) Diesel Models (From Serial Number Gs6915-6384 To Gs6916F-9067)
May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (ANSI / CSA) Diesel Models (from serial number GS6915-6384 to GS6916F-9067)
Page 223 Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (ANSI / CSA) Diesel Models (from serial number GS6915-6384 to GS6916F-9067) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 224 May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (ANS / CSA) Diesel Models (from serial number GS6915-6384 to GS6916F-9067) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 225 Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (ANSI / CSA) Diesel Models (from serial number GS6915-6384 to GS6916F-9067)
Page 226: Electrical Schematic, Gs-4069 Rt, (Ansi / Csa) Diesel Models (From Serial Number Gs6916F-9068)
May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (ANSI / CSA) Diesel Models (from serial number GS6916F-9068)
Page 227 Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (ANSI / CSA) Diesel Models (from serial number GS6916F-9068) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 228 May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (ANS / CSA) Diesel Models (from serial number GS6916F-9068) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 229 Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (ANSI / CSA) Diesel Models (from serial number GS6916F-9068)
Page 230: Electrical Schematic, Gs-4069 Rt, (As / Ce) Kubota Wg-972 Models (To Serial Number Gs6915-6383)
May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (AS / CE) Kubota WG-972 Models (to serial number GS6915-6383)
Page 231: Electrical Schematic, Gs-4069 Rt, (As / Ce Kubota Wg-972 Models (To Serial Number Gs6915-6383)
Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (AS / CE) Kubota WG-972 Models (to serial number GS6915-6383) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 232 May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (AS / CE) Kubota WG-972 Models (to serial number GS6915-6383) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 233 Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (AS / CE) Kubota WG-972 Models (to serial number GS6915-6383)
Page 234: Electrical Schematic, Gs-4069 Rt, (As / Ce) Kubota Wg-972 Models (From Serial Number Gs6915-6384 To Gs6916F-9067)
May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (AS / CE) Kubota WG-972 Models (from serial number GS6915-6384 to GS6916F-9067)
Page 235: Kubota Wg-972 Models (From Serial Number Gs6915-6384 To Gs6916F-9067)
Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (AS / CE) Kubota WG-972 Models (from serial number GS6915-6384 to GS6916F-9067) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 236 May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (AS / CE) Kubota WG-972 Models (from serial number GS6915-6384 to GS6916F-9067) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 237: Electrical Schematic, Gs-4069 Rt, (As / Ce
Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (AS / CE) Kubota WG-972 Models (from serial number GS6915-6384 to GS6916F-9067)
Page 238: Electrical Schematic, Gs-4069 Rt, (As / Ce) Kubota Wg-972 Models (From Serial Number Gs6916F-9068 To Gs6916F-9100)
May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (AS / CE) Kubota WG-972 Models (from serial number GS6916F-9068 to GS6916F-9100)
Page 239 Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (AS / CE) Kubota WG-972 Models (from serial number GS6916F-9068 to GS6916F-9100) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 240 May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (AS / CE) Kubota WG-972 Models (from serial number GS6916F-9068 to GS6916F-9100) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 241 Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (AS / CE) Kubota WG-972 Models (from serial number GS6916F-9068 to GS6916F-9100)
Page 242: Electrical Schematic, Gs-4069 Rt, (As / Ce) Gm .998L Models (From Serial Number Gs6916F-9101)
May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (AS / CE) GM .998L Models (from serial number GS6916F-9101)
Page 243 Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (AS / CE) GM .998L Models (from serial number GS6916F-9101) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 244 May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (AS / CE) GM .998L Models (from serial number GS6916F-9101) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 245 Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (AS / CE) GM .998L Models (from serial number GS6916F-9101)
Page 246: Electrical Schematic, Gs-4069 Rt, (As / Ce) Diesel Models (To Serial Number Gs6915-6383)
May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (AS / CE) Diesel Models (to serial number GS6915-6383)
Page 247 Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (AS / CE) Diesel Models (to serial number GS6915-6383) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 248 May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (AS / CE) Diesel Models (to serial number GS6915-6383) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 249 Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (AS / CE) Diesel Models (to serial number GS6915-6383)
Page 250: Electrical Schematic, Gs-4069 Rt, (As / Ce) Diesel Models (From Serial Number Gs6915-6384 To Gs6916F-9067)
May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (AS / CE) Diesel Models (from serial number GS6915-6384 to GS6916F-9067)
Page 251 Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (AS / CE) Diesel Models (from serial number GS6915-6384 to GS6916F-9067) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 252 May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (AS / CE) Diesel Models (from serial number GS6915-6384 to GS6916F-9067) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 253 Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (AS / CE) Diesel Models (from serial number GS6915-6384 to GS6916F-9067)
Page 254: Electrical Schematic, Gs-4069 Rt, (As / Ce) Diesel Models (From Serial Number Gs6916F-9068)
May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (AS / CE) Diesel Models (from serial number GS6916F-9068)
Page 255 Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (AS / CE) Diesel Models (from serial number GS6916F-9068) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 256 May 2018 Service and Repair Manual Electrical Schematic, GS-4069 RT, (AS / CE) Diesel Models (from serial number GS6916F-9068) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 257 Service and Repair Manual May 2018 Electrical Schematic, GS-4069 RT, (AS / CE) Diesel Models (from serial number GS6916F-9068)
Page 258: Hydraulic Schematic, Gs-2669 Rt And Gs-3369 Rt
May 2018 Service and Repair Manual Hydraulic Schematic, GS-2669 RT and GS-3369 RT (to serial number GS6915-6383)
Page 259: Hydraulic Schematic, Gs-2669 Rt And Gs-3369 Rt
Service and Repair Manual May 2018 Hydraulic Schematic, GS-2669 RT and GS-3369 RT (to serial number GS6915-6383) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 260: (From Serial Number Gs6915-6384)
May 2018 Service and Repair Manual Hydraulic Schematic, GS-2669 RT and GS3369 RT (from serial number GS6915-6384) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT...
Page 261 Service and Repair Manual May 2018 Hydraulic Schematic, GS-2669 RT and GS-3369 RT (from serial number GS6915-6384)
Page 262: Hydraulic Schematic, Gs-4069 Rt
May 2018 Service and Repair Manual Hydraulic Schematic, GS-4069 RT (to serial number GS6915-6383)
Page 263 Service and Repair Manual May 2018 Hydraulic Schematic, GS-4069 RT (to serial number GS6915-6383) ™ -2669 RT • GS ™ -3369 RT • GS ™ -4069 RT Part No. 1272219...
Page 264: (Ansi / Csa) - From Serial Number Gs6915-6384)
May 2018 Service and Repair Manual Hydraulic Schematic, GS-4069 RT (ANSI / CSA) - from serial number GS6915-6384) (AS / CE) - from serial number GS6915-6384 to GS6915-6573) Part No. 1272219 ™ -2669 RT • GS ™ -3369 RT • GS ™...
Page 265 Service and Repair Manual May 2018 Hydraulic Schematic, GS-4069 RT (ANSI / CSA) - from serial number GS6915-6384) (AS / CE) - from serial number GS6915-6384 to GS6915-6573)
Page 266: (As / Ce) - From Serial Number Gs6915-6574)
May 2018 Service and Repair Manual Hydraulic Schematic, GS-4069 RT (AS / CE) - from serial number GS6915-6574)
Page 267 Service and Repair Manual May 2018 Hydraulic Schematic, GS-4069 RT (AS / CE) - from serial number GS6915-6574) GS™- 2669 RT • GS™-3369 RT • GS™-4069 RT Part No. 1272219 Servic e and R epair M anual May 2018 ™ -2669 RT •...

This manual is also suitable for:

Gs-4069 Gs-3369

Genie GS-2669 Service And Repair Manual

Quick Links

Related Manuals for Genie GS-2669

Summary of Contents for Genie GS-2669

This manual is also suitable for:

Table of Contents