Figure 72 - Sample Printout (Setpoints) - York YK-EP B Operation & Maintenance Manual

SECTION 4 - PRINTING
YORK SETPOINTS
CHILLER ID 0
(c) 1997 – 2001 YORK INTERNATIONAL CORPORATION
Mon 22 Nov 1999 8:48:27 AM
Software Versions
----------------------------------------------------------------------------------
Controls
BIOS
Kernel
GUI
SIO
GPIC
Ext I/O
0110112091996
[Skip if External I/O board is not activated]
VSD [Skip if Motor Type is not VSD]
SSS [Skip if Motor Type is not Mod B SSS] = C.SSS.01.01
System Information
----------------------------------------------------------------------------------
System Language
Data Display Mode
Control Source
Remote Analog Input Range
Clock
Jumper Settings
----------------------------------------------------------------------------------
Pre-Run
Coastdown
Chilled Liquid Pump Operation
Refrigerant Selection
Anti-Recycle
Power Failure Restart
Liquid Type
Motor Type
Printer Setup
----------------------------------------------------------------------------------
Automatic Printer Logging
Log Start Time
Output Interval
Printer Type
Baud
Data Bits
Parity
Stop Bits
COM 2 Setup
----------------------------------------------------------------------------------
Baud
Data Bits
Parity
Stop Bits
Evaporator
----------------------------------------------------------------------------------
Leaving Chilled Local Setpoint
Leaving Chilled ISN Setpoint
Leaving Chilled Modem Setpoint
Leaving Chilled Analog Setpoint
Leaving Chilled Digital Setpoint

FIGURE 72 - SAMPLE PRINTOUT (SETPOINTS)

192
Remote Range
Sensitivity
Restart Offset
Restart Setpoint
Shutdown Offset
Shutdown Setpoint
Brine Low Evaporator Cutout
= C.MLM.01.04
Smart Freeze
= C.MLM.00.00
Refrigerant
= 0.18
= 0.28
Condenser
= 0.23
----------------------------------------------------------------------------------
= 0.04
High Pressure Warning Threshold
=
Drop Leg
Oil Sump
= C.VSD.00.00
----------------------------------------------------------------------------------
Oil Pump Package
Speed
Standby Lube
= English
[Skip the following section if Variable Speed Oil Pump
= English
is not installed]
= Local
Variable Speed Oil Pump
= 0–10 Volts
----------------------------------------------------------------------------------
= Enabled
Pressure Setpoint
Control Period
Proximity Probe
= Standard
----------------------------------------------------------------------------------
= Standard
High Speed Thrust Bearing Proximity Referenc = 41 Mils
= Standard
= R22
[Skip the following section if Liquid Level is not
= Enabled
= Auto
Refrigerant Level Control
= Water
----------------------------------------------------------------------------------
= Fixed Speed
Level Control
Setpoint
Period
Proportion Limit Open
= Disabled
Proportion Limit Close
= 12:00 am
Rate Limit Open
= 60 Min
Rate Limit Close
= Okidata
= 9600 Baud
[Skip the following section if Hot Gas Bypass is not
= 8 Bits
enabled]
= None
Hot Gas
= 1 Bit
----------------------------------------------------------------------------------
Hot Gas
Hold Period
Close Percentage
= 19200 Baud
Minimum Load
= 8 Bits
Maximum Open
= Odd
= 1 Bit
Surge
----------------------------------------------------------------------------------
Surge Sensitivity
Shutdown
= 45.0 ~F
Extended Run
= 45.0 ~F
Count Limit
= 45.0 ~F
Count Window
= 45.0 ~F
= 45.0 ~F
FIGURE 72 - SAMPLE PRINTOUT (SETPOINTS) (CONT'D)
FORM 160.87-OM1
ISSUE DATE: 8/24/2018
= 10.0 ~F
= Normal
= 0.0 ~F
= 45.0 ~F
= 4.0 ~F
= 41.0 ~F
= 54.3 Psig
= Off
= Enabled
= 246.3 Psig
= Enabled
= Variable
= On
= 35 Psid
= 0.9 Sec
enabled]
= On
= 50 %
= 3.5 Sec
= 15 %
= 45 %
= 10 %
= 10 %
= Enabled
= 30 Min
= 5 %
= 1 ~F
= 80 %
= 0.3
= Enabled
= Disabled
= 15
= 5 Min
JOHNSON CONTROLS