Omron NJ Series Troubleshooting Manual page 102

3 Error Tables
Event code Event name
54015496 hex Master Axis Gear
Ratio Numerator
Out of Range
54015497 hex Master Axis Gear
Ratio Denomina-
tor Out of Range
54015498 hex Auxiliary Axis Gear
Ratio Numerator
Out of Range
54015499 hex Auxiliary Axis Gear
Ratio Denomina-
tor Out of Range
5401549A hex Master Axis Posi-
tion Type Selec-
tion Out of Range
5401549B hex Auxiliary Axis Posi-
tion Type Selec-
tion Out of Range
5401549C hex Target Position
Ring Counter Out
of Range
5401549D hex Axes Group Com-
(Ver. 1.01) position Axis Set-
ting Out of Range
5401549E hex Axis Use Setting
(Ver. 1.04) Out of Range
54015700 hex Homing Parame-
(Ver. 1.03) ter Setting Out of
Range
54015702 hex Axis Use Change
(Ver. 1.04) Error
3-40
Meaning
The parameter specified for • Instruction input
the RatioNumeratorMaster
input variable to a motion
control instruction is out of
range.
The parameter specified for • Instruction input
the RatioDenominatorMas-
ter input variable to a
motion control instruction is
out of range.
The parameter specified for • Instruction input
the RatioNumeratorAuxil-
iary input variable to a
motion control instruction is
out of range.
The parameter specified for • Instruction input
the RatioDenominatorAuxil-
iary input variable to a
motion control instruction is
out of range.
The parameter specified for • Instruction input
the ReferenceTypeMaster
input variable to a motion
control instruction is out of
range.
The parameter specified for • Instruction input
the ReferenceTypeAuxil-
iary input variable to a
motion control instruction is
out of range.
Operation is not possible • High-speed homing
because the target position
is out of range for the ring
counter of the executed
instruction.
The parameter specified for • Instruction input
the Axes input variable to a
motion control instruction is
out of range.
The parameter specified for • Instruction input
the AxisUse input variable
to a motion control instruc-
tion is out of range.
The parameter specified for • Instruction input
the HomingParameter input
variable to a motion control
instruction is out of range.
The MC_ChangeAxisUse • The
(Change Axis Use) instruc-
tion was executed when the
axis was not stopped or
when the command veloc-
ity of the axis was satu-
rated.
Assumed cause
Maj Prt
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
was executed when 0
was not included in
the ring counter.
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
MC_ChangeAxisUse
(Change Axis Use)
instruction was exe-
cuted when the axis
was not stopped or
when the command
velocity of the axis
was saturated.
NJ-series Troubleshooting Manual (W503)
Level
Refer-
ence
Min Obs Info
S NJ-series
Instruc-
tions Ref-
erence
Manual
(Cat. No.
W502)
S Same as
above.
S Same as
above.
S Same as
above.
S Same as
above.
S Same as
above.
S Same as
above.
S Same as
above.
S Same as
above.
S Same as
above.
S Same as
above.