Command
Advanced Configuration (continued)
Front Panel Lock (Executive Mode)
Enable lock mode
Disable lock mode
View lock mode status
Overscan Mode (Applies only to SMPTE input rates: 480i, 576i, 1080i, 720p, 1080p, 2K, and 4K)
Set value
View status
Video Signal Presence
View signal presence —
non-xi model
View signal presence —
xi model
HDCP Notification
Set HDCP notification
View notification
Unsolicited Signal Statuses
Enable unsolicited
responses
Disable unsolicited
responses
View unsolicited
responses state
NOTE:
The following is an example of an unsolicited message that is generated by an xi model when both inputs
become disconnected: In00 0*0. In this message, In00 is the command tag and 0*0 represent inputs A * B.
X2(
=
Front panel lock mode (executive mode):
NOTE:
0 = Unlock front panel (default), 1 = Lock front panel.
X3*
=
Overscan mode:
0 = 0.0% — A true Auto-Image is executed on SMPTE inputs (default).
1 = 2.5% — Auto-Image commands snap to a 2.5% table (no true Auto-Image is performed).
2 = 5.0% — Auto-Image commands snap to a 5.0% table (no true Auto-Image is performed).
X6!
=
View video signal status:
0 = No video signal detected, 1 = Video signal detected.
X4&
=
HDCP notification mode: 0 = Black screen (notification disabled and output muted),
1 = Green screen with OSD message (default), 2 = User HDCP logo.
X4(
=
Unsolicited signal status response: 0 = Enabled, 1 = Disabled.
ASCII Command
Response
(Host to Scaler)
(Scaler to Host)
1 X
Exe 1
0 X
Exe 0
X
X2( ]
In verbose modes 2 and 3:
Exe
E
X3*
}
6*
OSCN
Oscn 6*
E
}
X3* ]
6 OSCN
In verbose modes 2 and 3:
Oscn 6*
E
}
X6! ]
0LS
In verbose modes 2 and 3:
In00 •
E
}
X6!
0LS
In verbose modes 2 and 3:
In00 •
E
X4&
}
N 1*
HDCP
Hdcp N 1*
E
}
X4& ]
N 1 HDCP
In verbose modes 2 and 3:
Hdcp N 1*
E
}
S 1 NTFY
Ntfy S 1
E
}
S 0 NTFY
Ntfy S 0
E
}
X4( ]
S NTFY
In verbose modes 2 and 3:
Ntfy S
DSC HD-HD 4K Plus A Series • Remote Configuration and Control
Additional Description
]
Lock the front panel controls.
Unlock front panel controls. All
]
front panel adjustments can be
made.
View current lock mode status
X2(
X2( ]
X3* ]
Set the selected input to
overscan mode
Show overscan mode status
X3*
X3* ]
View video signal status
X6! ]
X6! ]
*
View video signal status
both inputs (displayed as
InA*InB).
X6!
X6! ]
*
Set the HDCP notification to
X4& ]
X4&
View the HDCP notification
selection.
X4& ]
Enable unsolicited signal status
]
responses from the DSC.
Disable unsolicited responses
]
from the DSC (default).
View state (On-Off) of unsolicited
signal status responses.
X4( ]
.
X3*
.
for the input.
X6!
.
X6!
for
.
63