Extron electronics DSC HD-HD 4K Plus A Series User Manual page 66

Command
Output Configuration (continued)
HDMI Output Format
Set format
View setting
Power Save Mode
Power save off
Power save on
NOTE::: This mode can be exited via the
connecting the DSC to the computer via the PCS software.
View setting
Screen Saver (displayed when no active video signal is detected on the HDMI input)
Set screen saver mode
View mode
Set screen saver
duration before output
sync timeout
View screen saver
duration before output
sync timeout.
View screen saver
status
X@
NOTE: = Output: 1 = output A, 2 = output B (xi model only)
X2*
= Screen saver duration before output sync timeout — 1 through 500 seconds, in 1-second increments.
0 = The output sync is instantly disabled with no active input.
501 = Output sync never times out (default).
X4)
= Screen saver mode: 1 = black screen (default), 2 = blue output with OSD text
X4*
= HDMI output format:
0 = Auto (default). (HDMI RGB Full to HDMI sinks, or for pixel clocks greater than 165 MHz and DVI to
DVI sinks [only if the current output resolution is less than 165 MHz]).
1 = DVI (RGB 444, 0-255, no audio, no InfoFrames. Valid for output rates up to 165 MHz.)
2 = HDMI RGB Full (RGB 444, 0-255, audio, InfoFrames)
3 = HDMI RGB Limited (RGB 444, 16-235, audio, InfoFrames)
5 = HDMI YUV Limited (YUV 444, 16-235, audio, InfoFrames)
7 = HDMI YUV Limited (YUV 422, 16-235, audio, InfoFrames)
9 = HDMI YUV Limited (YUV 420, 16-235, audio, InfoFrames)
X6@
= Power saver mode: 0 = full power mode (default), 1 = low power due to overheating (query only)
X6#
= Screen saver status:
0 = active input detected, timer not running
1 = No active input detected, timer running, output sync active
2 = No active input detected, timer expired, output sync disabled
ASCII Command Response
(Host to Scaler) (Scaler to Host)
E X@ X4* }
* VTPO Vtpo
E X@ } X4* ]
VTPO
In verbose modes 2 and 3:
Vtpo
E }
0 PSAV Psav 0
E }
1 PSAV Psav 1
E }
0 PSAV
E } X6@ ]
PSAV
In verbose modes 2 and 3:
Psav
E X4) }
M 1* SSAV Ssav M 1*
E } X4) ]
M 1 SSAV
In verbose modes 2 and 3:
Ssav M 1*
E X2* }
T 1* SSAV Ssav T 1*
E } X2* ]
T 1 SSAV
In verbose modes 2 and 3:
Ssav T 1*
E } X6# ]
S 1 SSAV
In verbose modes 2 and 3:
Ssav S 1*
DSC HD-HD 4K Plus A Series • Remote Configuration and Control
X@ X4* ]
* Set output format
output
Show current HDMI output
format (
X@ X4* ]
*
]
]
command, by pressing any button on the front panel, or by
X6@ ]
X4) ]
X4) ]
X2* ]
X2* ]
X6# ]
Additional Description
X4*
for HDMI
X@
.
X4* X@
) for output .
Set the DSC to run in full power
mode (default).
Place the DSC in low power
mode.
X6@
View power save status .
Set the screen saver mode to
X4)
. Default = 1 (black).
View current screen saver
mode X4) .
Set the screen saver timeout
X2*
duration to seconds.
Default = 501 (never).
View screen saver timeout
X2*
duration .
X6#
View screen saver status .
58