Table of Contents
Advertisement
PS . Data System Control (WJ-FS416, WJ-MP204s and WJ-HD100)
This is a system example employing a WJ-FS416 (or FS409/FS316/FS309 instead), four WJ-MP204 and a WJ-HD100.
Connections
1. Connect MULTISCREEN OUT on the rear of the WJ-FS416 to VIDEO IN on the WJ-NT204 with a BNC attached coaxial
cable.
2. Connect PLAY IN on the rear of the WJ-FS416 to SPOT OUT on the WJ-HD100 with a BNC attached coaxial cable.
3. Connect REC OUT on the rear of the WJ-FS416 to VIDEO IN on the WJ-HD100 with a BNC attached coaxial cable.
4. Connect 16 Combination cameras to CAMERA IN 1-4 on WJ-MP204 unit #1 through #4 with coaxial cables.
5. Connect CAMERA OUT 1-4 on WJ-MP204 unit #1 through #4 to VIDEO IN 1-16 on the WJ-FS416.
6. Connect DATA terminals among WJ-FS416, WJ-MP204 and WJ-HD100 with RS-485 cables and branch connectors.
Note: Set DIP switch #3 on the
rear of WJ-NT204 to ON.
Setup for Peripheral Devices
1. Address Setup
Unit addresses must be set as follow.
Unit Name
WJ-FS416
WJ-HD100
WJ-MP204 #1
WJ-MP204 #2
WJ-MP204 #3
WJ-MP204 #4
2. PS.Data Communication Parameter Setup
Every unit must be set to the same parameter in their own setup menus.
(For example, BAUD RATE: 9600 bps, DATA BIT: 8 bits, STOP BIT: 1 bit, PARITY: NONE)
3. Input Assignment
For WJ-FS-416, open COMMUNICATION SETUP menu, and set CAMERA NUMBER to 001 through 016.
For WJ-MP204 units, open CAMERA CONFIG menu on each unit, and set CAM NO. (camera numbers) as follows.
Unit Name
WJ-MP204 #1
WJ-MP204 #2
WJ-MP204 #3
WJ-MP204 #4
For more information, refer to the manual included in each unit.
Setup for WJ-NT204 Transmitter
1. On the ADMINISTRATOR SETUP PAGE, click the MODE SETUP button to open the MODE SETUP window.
2. Select either H.323/H.261 or JPEG in the MAIN PAGE DEFAULT MODE & INDEX FILE SELECT area.
Make the CONTROL SETUP as follows.
CAM CONTROL:
AUX SYSTEM CONTROL: FS309/316/409/416
Default Unit Address:
Click SET & REBOOT. The WJ-NT204 transmitter will restart. Confirm the transmitter has restarted.
3. On the ADMINISTRATOR SETUP PAGE, click the SERIAL PORT button to open the SERIAL PORT SETUP window.
In the window, select PS.Data for TYPE, and set communication parameters the same as that other devices are set to.
127
Combination Camera 1-16
CAMERA IN 1-4
WJ-MP204
Ad 3
Ad 4
CAMERA OUT 1-4
VIDEO IN 1-16
Ad 1
POWER
WJ-FS416
ON
OFF
REC OUT
VIDEO IN
Ad 2
TIMER
HDD
MEMORY CARD
ALARM
OPERATE
SUSPEND
FULL
WJ-HD100
DAYLIGHT
SAVINGS
LOCK
VIDEO IN 1
LINK/
100
10BASE-T
BASE-TX CONNECT
ACT
POWER
WJ-NT204
ON
OFF
Unit Address
1 (set in its own setup menu)
2 (set in its own setup menu)
3 (set with UNIT switch on its front panel)
4 (set with UNIT switch)
5 (set with UNIT switch)
6 (set with UNIT switch)
CAM NO.
1CH through 4CH
5CH through 8CH
9CH through 12CH
13CH through 16CH
PS . Data
1
Ad 5
Ad 6
DATA
PLAY IN
MULTI
OUT
MONITOR OUT
PUSH– PAUSE
SET
DISPLAY SELECT
/
DATA
STOP
PLAY
REC
/
PLAY MODE SELECT
ALARM SEARCH
STEP
REW/FF
/
/
RING.VOL
LOW
HIGH
Network Interface Unit WJ-NT
Browser
Browser
LAN
Browser
Browser
Advertisement
Table of Contents
