Table of Contents
Advertisement
WJ-HD500 Digital Disk Recorder Control (Coax)
This is a system example that the WJ-NT204 transmitter has 4 of directly connected combination cameras while it has 12 of
combination cameras connected indirectly via the WJ-MP204 and WJ-HD500.
Connections
1. Connect 4 combination cameras to VIDEO IN 1-4 on the WJ-NT204 with coaxial cables.
2. Connect VIDEO OUT 1-4 on the WJ-NT204 to VIDEO IN 1-4 on the WJ-HD500.
3. Connect MULTISCREEN OUT on the rear of the WJ-HD500 to VIDEO AUX IN on the WJ-NT204 with a BNC attached coax-
ial cable.
4. Connect 12 combination cameras to CAMERA IN 1-4 on WJ-MP204 unit #1 through #3 with coaxial cables.
5. Connect CAMERA OUT 1-4 on WJ-MP204 unit #1 through #3 to VIDEO IN 5-16 on the WJ-HD500.
6. Connect DATA terminals among WJ-MP204, WJ-HD500 and WJ-NT204 with RS-485 cables and branch connectors.
Setup for Peripheral Devices
1. Address Setup
Unit addresses must be set as follow.
Unit Name
WJ-HD500
WJ-MP204 #1
WJ-MP204 #2
WJ-MP204 #3
2. Communication Parameter Setup
Every unit must be set to the same parameter in their own setup menus.
(For example, BAUD RATE: 9600 bps, DATA BIT: 8 bits, STOP BIT: 1 bit, PARITY: NONE)
3. Input Assignment
For WJ-MP204 units, open CAMERA CONFIG menu on each unit, and set CAM NO. (camera numbers) as follows.
Unit Name
WJ-MP204 #1
WJ-MP204 #2
WJ-MP204 #3
For more information, refer to the manual included in each unit.
Setup for WJ-NT204 Transmitter
1. On the ADMINISTRATOR SETUP PAGE, click the MODE SETUP button to open the MODE SETUP window.
2. Select either H.323/H.261 or JPEG in the MAIN PAGE DEFAULT MODE & INDEX FILE SELECT area.
Make the CONTROL SETUP as follows.
CAM CONTROL:
AUX SYSTEM CONTROL: HD500
Default Unit Address:
Click SET & REBOOT. The WJ-NT204 transmitter will restart. Confirm the transmitter has restarted.
3. On the ADMINISTRATOR SETUP PAGE, click the SERIAL PORT button to open the SERIAL PORT SETUP window.
In the window, select COAX for TYPE, and set communication parameters the same as that other devices are set to.
121
Combination Camera 5-16
5-8
9-12
CAMERA IN 1-4
WJ-MP204
Ad 2
Ad 3
CAMERA OUT 1-4
VIDEO IN 1-4 VIDEO IN 5-16
Ad 1
LOCK
1
2
3
4
REMOTE
ALARM
SET
SPOT
ALARM
MULTISCREEN
TIMER
RESET
5
6
7
8
WJ-HD500
MULTISCREEN
ALARM
SELECT
9
10
11
12
SUSPEND
OPERATE
HDD
SEQUENCE
13
14
15
16
FULL
MULTISCREEN OUT
VIDEO OUT 1-4
LINK/
100
RING.VOL
WJ-NT204
10BASE-T
BASE-TX CONNECT
ACT
POWER
ON
LOW
HIGH
OFF
VIDEO IN 1-4
Unit Address
1 (set in its own setup menu)
2 (set with UNIT switch on its front panel)
3 (set with UNIT switch)
4 (set with UNIT switch)
CAM NO.
5CH through 8CH
9CH through 12CH
13CH through 16CH
COAX
1
13-16
Ad 4
LAN
GROUP
STOP
BPLAY/ PAUSE
REC
FS
16
REC STOP
SELECT
DATA
REC PREVIEW
INDEX
REV
FWD
EL-ZOOM
ALARM SEARCH
SETUP
/ESC
COPY
DISPLAY
Digital Disk
DAYLIGHT SAVINGS
Recorder
WJ-HD
AUX IN
Network Interface Unit WJ-NT
Note: Set DIP switch #3 on the rear of WJ-NT204 to ON.
Browser
Browser
Browser
Browser
Advertisement
Table of Contents
