Inserting An Internal Effect Into A Channel - Yamaha CL1 Reference Manual

7.
Use the MIX1-16, MIX17-24 and MATRIX keys of the SELECTED CHANNEL section
(top panel) so that the SEND field shows the MIX bus that is patched as the effect
send.
You can also use the MIX1-16, MIX17-24 and MATRIX buttons in the SELECTED CHANNEL
VIEW screen to switch the displayed bus.
8.
Press the TO MIX SEND LEVEL knob that corresponds to the desired MIX bus, and
turn the multifunction knob to adjust the send level of the signal sent from each
channel to the MIX bus.
In this state you can adjust the send level of the signal sent from the input channel to the internal
effect. Adjust the send level of other input channels in the same way.
If you press the selected knob once again, the MIX SEND popup window (8ch) for the send-
destination MIX bus will appear. This popup window contains on/off switches for the signals sent
from each channel to the corresponding bus, and lets you select the send point (PRE or POST)
(see page 41).
NOTE
At this time, you make sure that the send level from the ST IN channel you selected in step 3 to
the corresponding MIX bus is set to –∞ dB. If you raise this send level, the output of the effect will
be returned to the input of the same effect, possibly causing oscillation.
9.
To adjust the master level of the effect send, call up the MIX channel you specified
as the input-source of the rack in step 2 to the Centralogic section, and adjust the
corresponding fader.
Set the level as high as possible without allowing the post-effect signal to reach the overload point.
NOTE
The input and output levels of the effect are shown by the input/output meters in the upper right
of the EFFECT popup window.
10.
To adjust the effect return level, operate the ST IN channel that you selected as the
output-destination for the rack in step 3.

Inserting an internal effect into a channel

This section explains how to insert an effect into a channel by assigning the input/output of the internal
effect to the input/output of the desired channel (except for a ST IN channel).
1.
Follow steps 1–3 described in "Virtual rack
effect in a rack.
The rack in which an effect is mounted will indicate the effect type used by that effect, the number
of inputs and outputs, and the levels before and after the effect.
operations" on page 115, to mount an
2.
Press the L side of the INPUT PATCH button to open the CH SELECT popup window,
and select the insert-out of a channel as the input-source.
For details on the CH SELECT popup window, refer to step 5 of
page 115. Insert-out is now assigned to the L input of the effect.
3.
Press the L side of the OUTPUT PATCH button to open the CH SELECT popup
window, and select the insert-in of the same channel as the output-destination.
For details on the CH SELECT popup window, refer to step 6 of
page 115. Insert-in is now assigned to the L output of the effect.
If you are inserting an effect into a channel that handles a stereo source, assign the R channel
insert-out/insert-in to the R input and output.
4.
Use the Bank Select keys in the Centralogic section to access the OVERVIEW screen
for the channel into which you inserted the effect.
5.
Press the INSERT/DIRECT OUT field to access the INSERT/DIRECT OUT popup
window.
Make sure that the rack you inserted into the input and output ports is selected. For more
information on insert-out/in, see
6.
Turn on the INSERT ON/OFF button for the channel into which you inserted the
effect.
If it is off, press the button to turn it on. In this state, effect insertion is enabled for the
corresponding channel.
7.
In the Function Access Area, press the RACK button to access the VIRTUAL RACK
window, and use the EFFECT tab to display the EFFECT field.
8.
Press the effect rack that you inserted into the channel. The EFFECT popup window
will appear.
In this popup window you can edit the effect parameters.
9.
Select the effect type and edit the effect parameters.
For details on editing the effect parameters, refer to "Editing the internal effect parameters. "
NOTE
• The levels before and after the effect are shown by the input and output meters in the upper right
of the EFFECT popup window.
• Adjust the effect send master level and the effect parameters so that the signal does not reach
the overload point at the input or output stage of the effect.
10.
Using the fader of the channel you selected as the rack's output destination in step
3, adjust the level as appropriate.
124
Graphic EQ, effects, and Premium Rack
"Virtual rack
"Virtual rack
"Inserting an external device into a channel" on
operations" on
operations" on
page 21.
Reference Manual