Inserting An External Device Into A Channel - Yamaha CL5 Reference Manual

CH SELECT screen
1
1 Category select list
Select the category of the channel. The categories correspond to the following channels.
They vary depending on the output port
• MIX/MATRIX .......................... MIX 1 - MIX 24, MATRIX 1 - MATRIX 8
• ST/MONO/MONI/CUE ........... STEREO L, STEREO R, MONO (C), MONI L, MONI R,
MONI C, CUE L, CUE R, SMON L, SMON R, SMON C,
SMON LFE, SMON Ls, SMON Rs, MMTX L, MMTX R,
MMTX C, MMTX LFE, MMTX Ls, MMTX Rs
• DIRECT OUT 1-32 ................. CH 1 - CH 32 Direct Outs
• DIRECT OUT 33-64 ............... CH 33 - CH 64 Direct Outs
• DIRECT OUT 65-72 ............... CH 65 - CH 72 Direct Outs
• INSERT OUT 1-32 ................. CH 1 - CH 32 Insert Outs
• INSERT OUT 33-64 ............... CH 33 - CH 64 Insert Outs
• INSERT OUT 65-72 ............... CH 65 - CH 72 Insert Outs
• INSERT OUT MIX/MATRIX.... MIX 1 - MIX 24, MATRIX 1 - MATRIX 8 Insert Outs
• INSERT OUT ST/MONO........ STEREO L, STEREO R, MONO (C) Insert Outs
• CASCADE MIX/MATRIX ........ MIX 1 - MIX 24, MATRIX 1 - MATRIX 8
• CASCADE ST/MONO/CUE ... STEREO L, STEREO R, MONO (C), CUE L, CUE R
NOTE
In the case of the CL3/CL1, channels that do not exist on those models will not be shown.
2
Channel select button
Select the channel to be assigned to the output port from the current category.
3
CLOSE button
Closes the screen.
2
3
type.

Inserting an external device into a channel

You can insert an effect processor or other external device into the signal path of an INPUT,
MIX, MATRIX, STEREO, or MONO channel. When doing so, the type of input/output port
used for the insertion and the location of the insertion in/out can be specified individually for
each channel.
STEP
1. Connect your external equipment to an OMNI IN/OUT jack or to an I/O card
installed in slots 1 - 3.
2. Use the Bank Select keys in the Centralogic section to select the channel to which
you want to assign the input source.
3. Press the INSERT/DIRECT OUT field.
4. Press the INSERT OUT or INSERT IN button.
5. Select an output port or an input port.
6. Press the INSERT ON button.
OVERVIEW screen
NOTE
• If you install a digital I/O card in a slot and digitally connect an external device, you must
synchronize the word clock of the CL console and the external device
• There is a limit to the sum of INSERT 1 and INSERT 2 for each channel group, as shown in the
table below. You can select any output or input ports.
CH1-16 CH17-32 CH33-48
INSERT 16 16
OUT
INSERT IN 16 16
* When using Surround mode
20
Input and output patching
INSERT/DIRECT OUT Screen (8ch)
(page 218).
CH49-64
CH65-72 MIX1-24/
(CL5 and MATRIX
(CL5 ST/
CL3
only) MONO
only)
16 16 8 30(24)*
16 16 8 30(24)*
Reference Manual
1-8
8
8