Table of Contents
Advertisement
API Command Reference
Command Summary
Command
@
Trigger On Command
*B
Flush Acquisition
Buffer
*C
Clear Channel
Configuration
*F
Restore Factory
Settings
*K
Change Calibration
Keyword
*P
Adjust Calibration Card
Pots
*R
Power-On Reset
*S
Power-Up Settings
*T
Time Stamping
A
Assign Alarm Output
A#
Alarm Stamping
C
Configure Channels
C#
Select Card
A-6
Syntax
@
Trigger on receipt of an
*B
Flush any data currently in the acquisition buffer.
*C
Clear out the channel configuration so that no channels are
configured.
*F
Restore unit to factory configuration.
*Kkey
Change the calibration keyword, where
form of a 5-digit number
be no longer than 5 characters.
*Pchan
Select voltage level to be enabled for adjustment. Valid options
for
chan
02
- Enable +4.4. Volt Source on calibration card, and
Select 0 Volts GND.
*R
Power-on reset. Equivalent to hardware reset.
*Smode
Specify power-up configuration mode. Valid options for
0
- Power-up under last known configuration (default), and
Power-up under factory default configuration.
*Tstate
Specify whether or not time stamping will be enabled. Valid
options for
Enable absolute time stamping, and
stamping
Achans,
Set alarm condition where
output
the digital output.
chans
may be in two forms:
<
chan
where
1
where
max
is the digital output number to associate the channel(s)
output
with, where
A?
Query channels assigned to digital output.
A#state
Specify whether or not alarm stamping will be enabled. Valid
options for
and
1
- Enable alarm stamping.
Cchans,
Configure the channels for the master unit and its slave units.
type
chans
[,
[lowsp],
highsp
[highsp],
chans
may be in two forms:
[hyst] ]
<
chan
where
1
where max = 128 for NetScan.
The chassis is
type
is the type to assign to those channels.
C?
Query current channel configuration.
C#card
Select the card from which subsequent
interrogation will retrieve information.
Without optional Relay Card
Valid options for
Selects the card in corresponding slot of the main unit (with 1
being the bottom slot); and 5, 6, 7, or 8 - Selects the
corresponding slot on the expansion chassis (with slot 5 being
the bottom slot of the expansion chassis.
With optional Relay Card (installs in slot 1)
Valid options for
card in slot 2, 2 selects card in slot 3; and so on, with 7
selecting the card in slot 8; and no card 8 available.
Description
@
.
nnnnn
. Therefore the password can
are:
01
- Enable -4.4 Volt Source on calibration card,
state
are:
0
- Disable time stamping (default),
2
chans
is the channel(s) to assign to
chan
(for a single channel where
<
max
) or
first-last
(for a range of channels
<
first
<
last
<
max
),
= 128 for NetScan.
0
<
output
<
32
.
are:
- Disable alarm stamping (default),
state
0
and
are required arguments, while
type
and
hyst
are optional.
chan
(for a single channel where
<
max
) or
first-last
(for a range of channels
<
<
<
),
first
last
max
chan = 0
.
card
are:
0
- Selects the chassis; 1, 2, 3, or 4 -
card
are:
0
- Selects the chassis; 1 selects
Appendix A
is the keyword in the
key
03
-
mode
are:
1
-
1
-
- Enable relative time
1
,
lowsp
1
QC?
and
U12
NetScan User's Manual
Advertisement
Chapters
Table of Contents
