Sharp AR-C150 Service Manual page 206

Simulation
Code
Main Sub.
43 01 Fusing temperature setup
(AR-C250/C160/C270)
07 Fusing oil pump operation
setup
44 01 Image density correction
(Process control)
operation mode setup
04 Image density correction
(Process control) target
level setup
05 Image density correction
(Process control) initial
developing bias voltage
setup
06 Image forming section
correction (Process
control) forcible execution
13 Image density sensor
sense level adjustment
20 OPC drum phase
adjustment (Old)
21 Half tone image correction
initial setup
23 Image density sensor
sense position adjustment
26 Half tone image correction
forcible execution
27 Half tone image correction
data reset
∗1: AR-C160/C270
Content/Item
A: Temperature set value (upper)
B: Temperature set value (lower)
C: Temperature set value (Ready
upper)
D: Temperature set value (Ready
lower)
E: Temperature set value (Energy
saving upper)
F: Temperature set value (Energy
saving reset)
G: Temperature set value (Thick
paper (1) upper)
H: Temperature set value (Thick
paper (1) lower)
I: Temperature set value (Thick
paper (2) upper)
J: Temperature set value (Thick
paper (2) lower)
K: Temperature set value (OHP
upper)
L: Temperature set value (OHP
lower)
A: Pump ON time
B: Pump interval time
Operation mode
A: Color image density sensor
B: Black image density sensor
C: Target density level (Yellow)
D: Target density level (Magenta)
E: Target density level (Cyan)
F: Target density level (Black)
A: (Black)
B: (Cyan)
C: (Magenta)
D: (Yellow)
Sensor LED level
Dark voltage level
Calibration sheet sense level
Calibration plate sense level
A: Print mode
B: Cyan OPC drum phase
C: Magenta OPC drum phase
D: Yellow OPC drum phase
E: Paper (Paper tray)
Initial setup data
Adjustment value
Correction data
Correction data
Set range Default
AR- AR-
C100 C150
70 – 200
70 – 200
70 – 200
70 – 200
70 – 200
70 – 200
70 – 210
70 – 200
70 – 210
70 – 200
70 – 200
70 – 200
❍ ❍
5 – 50 12
❍ ❍
17 – 250 130
❍ ❍
All ON
❍ ❍
0 – 200 102
❍ ❍
0 – 200 133
❍ ❍
0 – 200 90
❍ ❍
0 – 200 100
❍ ❍
0 – 200 83
❍ ❍
0 – 200 15
22
❍ ❍
0 – 700 325
❍ ❍
0 – 700 325
❍ ❍
0 – 700 325
❍ ❍
0 – 700 325
❍ ❍
❍ ❍
0 – 255 128
❍ ❍
0 – 255 30
❍ ❍
0 – 255 102
❍ ❍
0 – 255 80
❍ ❍
1 – 3 3
❍ ❍
0 – 330 60
❍ ❍
0 – 330 120
❍ ❍
0 – 330 180
❍ ❍
1 – 6 5
❍ ❍
0 – 255 —
❍ ❍
40 – 60 50
❍ ❍
245 – 755 500
(1 – 1999) ∗1 (1000) ∗1
❍ ❍
245 – 755 500
(1 – 1999) ∗1 (1000) ∗1
14 – 11A
Model
NOTE
AR-
AR-
C160/
C250
C270
❍ ❍
The set value
❍ ❍
(default) differs
❍ ❍
depending on the
destination. Refer to
❍ ❍ the details of SIM
43-01.
❍ ❍
❍ ❍
❍ ❍
❍ ❍
❍ ❍
❍ ❍
❍ ❍
❍ ❍
❍ ❍
❍ ❍
❍ ❍
❍ ❍
❍ ❍
❍ ❍
❍ ❍
❍ ❍
❍ ❍
❍ ❍
❍ ❍
❍ ❍
❍ ❍
❍ ❍
The adjustment value
cannot be entered
directly.
❍ ❍
The adjustment value
❍ ❍
cannot be entered
❍ ❍
directly.
❍ ❍
The set up data is
not stored.
The set up data is
not stored.
❍ ❍
The set up data
cannot be entered
directly.
❍ ❍
The adjustment value
cannot be entered
directly.
❍ ❍
The correction data
cannot be entered
directly.
❍ ❍
Data store
location
EEPROM
(PCU PWB)
EEPROM
(PCU PWB)
EEPROM
(PCU PWB)
EEPROM
(PCU PWB)
EEPROM
(PCU PWB)
EEPROM
(PCU PWB)
EEPROM
(PCU PWB)
EEPROM
(PCU PWB)
EEPROM
(ICU PWB)
EEPROM
(ICU PWB)
EEPROM
(ICU PWB)
EEPROM
(ICU PWB)