Sharp AR-C150 Service Manual page 105

Code
Function (Purpose)
Main Sub
24 7 Used to clear the OPC drum (membrane
decrease) correction counter. (Performed
when the OPC drum is replaced.)
8 Used to clear the waste toner counter in the
transfer section.
9 Used to clear the self print and the list print
counter. "(After completion of maintenance,
this counter is cleared.
(AR-C150/C250/C160/C270)
25 1 Used to check the operation of the main
drive (excluding the scanner section) and the
toner density sensor. (The toner density
sensor output can be monitored.)
2 Used to make the initial setup (automatic
adjustment) of toner density when replacing
developer.
26 1 Used to make option setup. (When installing
an option, this simulation is used to setup for
that option (software).
(AR-C150/C250/C160/C270)
2 1) Used to set the paper size of the large
capacity tray. (When the paper size is
changed, the software setup must be
changed accordingly with this simulation.)
2) Used to detect 8.5 × 13 (INCH Series)
paper or documents and to set the display
mode. (All paper feed modes)
3) Used to set the display form of the paper
kind in the manual paper feed mode.
3 Used to set the auditor specification mode.
Setting must be made according to the use
conditions of the auditor.
5 Used to set the count mode of the total
counter, the developer counter, and the
maintenance counter.
6 1)Used to set the specifications (paper, fixed
copy magnification ratio, machine operations
in case of an image (process) correction
error) according to the destination.
(AR-C150/C250/C160/C270)
2) Used to set the user logo. (AR-C100 only)
18 Used to set YES/NO of toner save operation.
(This simulation is valid only for Japan and
UK versions. It depends on Sim 26-6
(Destination) setting. For the other
destinations, the same setting can be made
by the user program P22. (Effective only in
the monochrome copy mode)
22 Used to set the specification (language) for
the destination. (AR-C150/C250/C160/C270)
28 Used to set the AC power voltage. (For
control of the fusing section heater lamp)
30 Used to set the CE mark complying
operation mode. (Conforms to the soft start
when driving the fusing heater lamp.)
32 Used to set the fan rotating speed. (low
speed)
35 Used to set whether the trouble history
display by SIM 22-4 is displayed as one
trouble or as the accumulated number of
continuous troubles when two or more
troubles of same kind occur continuously.
45 Used to set the copy charge. (AR-C100 only) Setting
52 Used to set YES/NO of count up of non-copy
paper (cover or insertion paper).
53 Used by the user to set Enable/Disable auto
color calibration (auto adjustment of color
balance and density)
54 Used to adjust the brightness of LCD display.
(AR-C250 only)
Purpose
Data clear Image process
(Photoconductor/
Developing/Transfer/
Cleaning)
Data clear Image process
(Photoconductor/
Developing/Transfer/
Cleaning)
Data clear Printer
Operation test/check Image process
(Photoconductor/
Developing/Transfer/
Cleaning)
Setting Image process
(Photoconductor/
Developing/Transfer/
Cleaning)
Setting
Setting Paper transport
Setting Auditor
Setting
Setting
Setting
Setting
Setting Power supply
(DC/AC/High)
Setting Fixing (Fusing)
Setting
Setting
Setting
setting
Adjustment LCD display
8 – 5
Section
Photo Counter
conductor
Copy Counter
Counter
Developer/ Operation
Toner Hopper
Developer/
Toner Hopper
Specifications
Specifications
Specifications
Specifications
Specifications
Specifications
Specifications
Operation
Specifications
Operation
Specifications
Specifications
Specification
Specifications
Operation
Item
Photo conductor
Printer
Options
Counter
Destination
Operation mode
(Common)
Language
Operation mode
(Common)
Others
Operation mode
Operation mode