Section 5. Operation; Initial Start-Up Precautions; Operating The Controller; Center - Zodiac Jandy Pro Series JE1500T Installation And Operation Manual

Page 18
ENGLISH

section 5. operation

Caution
Do not use this heat pump if any part has
been under water. Immediately call a qualified
service technician to inspect the heater and
replace any part of the control system which
has been under water.
Caution
Keep all objects off the top of the heat pump.
Blocking air flow could damage the unit and
may void the warranty.
5.1

initial start-up precautions

Be sure that there is water in the pool and that the
surface level is above the skimmer or other inlet of the
pool's filter system.
With any new pool or spa installation, operate the filter
pump with the heat pump off long enough to completely
clean the water. This will remove any installation
residue from the water.
Clean the filter at the end of this operation before
starting the heat pump. When raising the temperature
of a cold pool, program the time clock to run the pump
continuously.
AquaLink Touch
Thu January, 2009 3:03 PM
Pool Temp Air Temp
86º 78º
FILTER SPA POOL SPA AUX1 AUX2 AUX3 Other
PUMP HEAT HEAT Devices
On/Off
Home Menu OneTouch Help Back Status Photos Power
OR
OR
®
JANDY AquaLink RS
06/26/04 MON
6:00 PM
FILTER PUMP OFF
AIR 79°
EQUIPMENT ON/OFF
ONETOUCH ON/OFF
MENU / HELP
4-Conductor
Wire
RED
BLK
YEL
GRN
Jandy Pro Series JE Heat Pump Power Interface
Figure 13. Jandy pro series JE Heat pump to
power Center - rs485 (4 wire) connection
®
Jandy Pro Series JE Heat Pumps
This lets the filter system and heat pump operate
continuously until the water reaches the temperature
setting on the temperature control. When that happens,
the heat pump will automatically shut off, but the filter
pump will keep running.
5.2
Your new Jandy Pro Series JE heat pump is controlled
by an advanced microprocessor based controller that
provides a sophisticated yet simple interface to operate
your heat pump for maximum efficiency and enjoyment
of your pool. To locate the control buttons, see Figure
14.
When the control panel is turned off, the screen displays
HEat puMp is oFF prEss pool or spa .
To enable the pool mode, press pool . The associated
left green LED indicator will light and the unit will
display sEt:xxx° .
notE
You can change the temperature set point by pressing
the up or down button . Repeatedly press the up or
down button until you reach the desired temperature set
point. After 5 seconds of inactivity, the new set point is
stored in memory.
When the water temperature falls to 1 degree below
4 3 2 1
the temperature setting
control will start the heat pump and the associated right
4 3 2 1 4 3 2 1 6 5 4 3 2 1 10 9 8 7 6 5 4 3 2 1
RS6 & RS8 ONLY RS8 ONLY
S1 RESET POOL MODE
AUTO SPA MODE
SPA DRAIN
SERVICE HEATER SOLAR
TIME OUT SPA FILL
LED will light RED
S2
OPTIONAL
If connected, the Maintain Heat mode allows the heat
pump to monitor the temperature of the water 24 hours
a day by turning the pool pump on and sampling the
water temperature.
RS Power
A Maintain Temp Relay is required and the feature must

Center

be enabled.
When the water temperature drops below the
programmed temperature set point, the control will start
the heat pump.
To operate in pool mode with the Maintain Heat feature,
press pool , then press MEnu, press the down button
until Maintain pool HEat is displayed, press the
MEnu button.
The associated left green LED indicator will light and
the unit will display sEt:xxx°. Change the temperature
set point by pressing the up or down button until
the desired set point is displayed. After 5 seconds of
inactivity, the new set point is stored in memory.
|
Installation and Operation Manual

operating the Controller

off Mode
pool Mode - (normal Heat)
XXX
represents the current temperature setting
on the control. The default setting for pool
temperature is 80°F (26°C).
and
after a 5 minute delay, the
.
pool Mode - (optional Maintain Heat)