Contura 510 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Contura Manuals
  4. Wood stove
  5. 510
  6. Installation instructions manual

Contura 510 Installation Instructions Manual

Hide thumbs Also See for 510:

Advertisement

Table of Contents

Installationsanvisning
SE
Installationsanleitung 32
DE
Installasjonsanvisning 64
NO
Installation instruction 96
GB
installations
2
ANVISNING
  
www.contura.eu
500

Advertisement

Table of Contents
loading

Related Manuals for Contura 510

Summary of Contents for Contura 510

  • Page 1    Installationsanvisning Installationsanleitung 32 Installasjonsanvisning 64 ANVISNING Installation instruction 96 www.contura.eu...
  • Page 2 Assembling the surround – Contura 520T  ..... 107 Assembling the surround – Contura 560T  ..... . 111 ...
  • Page 3 Emission of CO: 0,11% Certificate number for  Safety measurments for Contura 500-series: Distance to adjacent combustible materials: P Marking: 22 03 09 C 510, 550, 570, 580, 585, 590 Behind 100 mm, beside 500 mm C 520T Behind 100 mm, beside 470 mm C 560T, 560K, 590T Behind 100 mm, beside 480 mm Manufacturer’s assurance Manufacture of the product  Manufacturing check by approved organisation has taken place in accordance ...

  • Page 4: General Information

    This folder contains instructions on how to assem- Check to make sure that the floor is strong enough ble and install stoves in the Contura 500 series. The to support the weight of the stove and chimney. If stove also comes with comprehensive Lighting and you intend to locate the stove on standard wooden Maintenance Instructions.

  • Page 5: Installation Distances To Walls And Ceiling

    A separate glass floor plate (accessory) increases Combustible roof the connection height to the chimney by 10mm. 510/550/550A Install the spacers supplied with the floor plate prior to connection. Combustible wall Ø150 Air inlet Ø67...
  • Page 6 560T/560K Combustible roof Combustible wall Ø150 Air inlet Ø67 Air inlet Ø67 Fire-retardant wall of brick or concrete Fire-retardant wall of brick or concrete Combustible wall 320* *See 570 * To avoid any discoloration of painted walls made of non- combustibl e materials, we recommend the same gap between Combustible roof stove and wall as that for walls in combustible materials.
  • Page 7 Combustible roof Combustible wall Ø150 Ø 510 Air inlet Ø67 Air inlet Ø67 Fire-retardant wall of brick or concrete Fire-retardant wall of Combustible wall brick or concrete *See 570 320* Combustible roof Combustible wall Ø150 Air inlet Ø67 Ø 510 Air inlet Ø67...

  • Page 8: Air Supply

    Air supply Combustion air for the stove can be supplied through a duct directly from outside, or indirectly through a vent in the wall of the room where the stove is installed. The drawings on the right show various alternative methods of supplying the stove with air.

  • Page 9: Unpacking

    Unpacking Leave the stove body screwed in place on the deli- very pallet. Remove the components and accessories supplied in the delivery package and place them on one side. Dismantle any loose components in the fire- box (grate disc, fire-box surround, etc.) and the heat reflector underneath.

  • Page 10: Connection To A Chimney

    Top flue connection to a chimney When installing the chimney, please refer to the manufacturer’s installation instructions. Below we explain how to connect the chimney to the stove. Stoves are supplied from the factory ready for connecting to a top flue. To prepare the stove for connection to a rear flue, the connecting collar and covering cap need to change places.

  • Page 11: Assembling The Surround – Contura 510/550/550A

    510/550/550A Assembling the surround – Contura 510/550/550A Lay the stove body on its back on the pallet. Secure Loosen the two screws on the rear of the base-frame the base-plate with four socket-head (female) screws. by turning them three revolutions anticlockwise.
  • Page 12 Please read carefully through the separate “Lighting and Maintenance Instructions for the Contura 500 series” before lighting the stove for the first time. Fix the manufacturer’s markings that give details of the serial number and safe installation distances on the heat reflector, as shown.

  • Page 13: Assembling The Surround – Contura 520T

    520T Assembling the surround Contura 520T Lay the stove body on its back on the pallet. Install the Slacken off the two rear screws for the base frame by base plate with four Allen screws. Screw from the inside three revolutions and hook the rear panel into place.
  • Page 14 520T Installing the soapstone Position the stove body on the hearth plate and check the installation distances. Connection to the chimney from the rear of the stove body is carried out prior to installing the soapstone. When connecting the chimney to the top of the stove body the soapstone surround must be installed first.
  • Page 15 520T Apply six small blobs of silicone on each side of the base plate. Carefully position the soapstone sides. Start with the front stone which is slightly smaller than the rear stone. The bottom edge of the soapstone sides must be 3 mm outside the base plate.
  • Page 16 Important! Before the stove is used, it must be inspected by an authorised chimney sweep. Read the ”Instructions for lighting and maintenance for the Contura 500 series” before lighting the fire for the first time.

  • Page 17: Assembling The Surround – Contura 560T

    560T Assembling the surround – Contura 560T Lay the stove body on its back on the pallet. Secure Loosen the two screws on the rear of the base-frame the base-plate with four socket-head (female) screws. by turning them three revolutions anticlockwise.
  • Page 18 560T Lay the top frame on the top of the stove body, hoo- king it in place over the screws at the top of the rear panel. Do not tighten the screws until the soapstone sides are in place. Fitting the soapstone Stand the stove on the floor plate and check the safe installation distances.
  • Page 19 560T Squeeze twelve small blobs of silicone onto the Screw the plate into place over the joint in the two connecting plate. soapstone sections. Insert a screw into the top end of the soapstone side section and turn the screw two revolutions only.
  • Page 20 Before the stove is used, it must be inspected by an authorised chimney sweep or the relevant authority. Please read carefully through the separate “Lighting and Maintenance Instructions for the Contura 500 serie s” before lighting the stove for the first time.

  • Page 21: Assembling The Surround – Contura 560K

    560K Assembling the surround – Contura 560K Lay the stove body on its back on the pallet. Secure Loosen the two screws on the rear of the base-frame the base-plate with four socket-head (female) screws. by turning them three revolutions anticlockwise.
  • Page 22 560K Lay the top frame on the top of the stove body, hoo- king it in place over the screws at the top of the rear panel. Do not tighten the screws until the tiled sides are in place. Fitting the tiles Stand the stove on the floor plate and check the safe installation distances.
  • Page 23 560K Lay the steel profile in place and fit the screws loo- Seal the insides of the joints between the tiles with sely. Adjust the gap between the tiles until the overall a bead of silicone. length of the tiled side section measures 968 mm. Screw the steel profile into place in the threaded holes in the back of the tiles.
  • Page 24 Before the stove is used, it must be inspected by an authorised chimney sweep or the relevant authority. Please read carefully through the separate “Lighting and Maintenance Instructions for the Contura 500 series” before lighting the stove for the first time.

  • Page 25: Assembling The Surround – Contura 570

    Assembling the surround – Contura 570 Lay the stove body on its back on the pallet. Secure Loosen the two screws on the rear of the base-frame the base-plate with four socket-head (female) screws. by turning them three revolutions anticlockwise.
  • Page 26 Important! Important! To make it easier to fit the side panels, do not Clean the glass carefully before fitting the side tighten the two top screws holding the rear panel panels. until the side panels are in place. Slide the bottom edge of the retaining bracket for the glass under the screen, and then ease the bracket up so that the top edge also fits under the screen.
  • Page 27 Before the stove is used, it must be inspected by an authorised chimney sweep or the relevant authority. Please read carefully through the separate “Lighting and Maintenance Instructions for the Contura 500 series” before lighting the stove for the first time.

  • Page 28: Assembling The Surround – Contura 580/585

    580/585 Assembling the surround – Contura 580/585 There is a removable panel at the rear of the pedestal base. This is used when installing an external air supply connection. To remove, unscrew the screws along the top edge of the panel.
  • Page 29 580/585 Lay the stove body on its back on the pallet so that Fit the pedestal base using the screws removed from the entire base-frame projects beyond the pallet. the base-frame. Do not tighten the screws until the Remove the base-frame by unscrewing the four stove is standing upright on a level surface.
  • Page 30 Before the stove is used, it must be inspected by an authorised chimney sweep or the relevant authority. Please read carefully through the separate “Lighting and Maintenance Instructions for the Contura 500 series” before lighting the stove for the first time.
  • Page 31 Important! When fitting a plinth, the punched metal section in the rear panel must be removed to allow a supply of convection air to the stove. Fitting a plinth Loosen the front socket-head screw holding the base-plate. Fit the clip-on bracket using two socket-head screws Press the folded edges of the plinth into place in the per bracket.
  • Page 32 Important! When fitting a plinth drawer, the punched metal section in the rear panel must be removed to allow a supply of convection air to the stove. Fitting a plinth drawer Loosen the front socket-head screw by turning into through three revolutions. Lay the drawer slide in place on the base-plate.
  • Page 33 NIBE AB/NIBE BRASVÄRME · Box 134 · 285 23 Markaryd www.contura.eu Nibe Brasvärme reserves the right to change  colours, materials, dimensions and models at  any time without special notice. Your dealer can  IAV SE-EX 0726-6 611821 provide you with the latest information. ...

This manual is also suitable for:

570520t560t560k580585 ... Show all

Table of Contents