Torque Requirements; Lubrication; Ford Engine Oil Specifications; Deutz Engine Oil Specifications - JLG 600SJ Service And Maintenance Manual

1.5 TORQUE REQUIREMENTS

Table 1-16. Torque Requirements
Description
Bearing To Chassis
Bearing To Turntable
Wire Rope
Wheel Lugs
Engine Mounting Bolts
Engine Manifold Mounting
Bolts
*Check swing bearing bolts for security after first 50 hours of opera-
tion and every 600 hours thereafter. (See Swing Bearing in Section
3.)
NOTE: When maintenance becomes necessary or a
fastener has loosened, refer to the Torque Chart
to determine proper torque value.

1.6 LUBRICATION

Ford Engine Oil Specifications

Single Viscosity Oils (SF, SF-SE, SF-CC, SF-CD)
When Outside
Temperature is
Consistently
-10°F. to +60°F
(-24°C. to +16°C.)
+10°F. to +90°F
(+12°C. to +32°C.)
Above +32°F. (+0°C.)
Above +50°F. (+10°C.)
Multi-Viscosity Oil. (SF, SF-SE, SF-CC, SF-CD)
*Not recommended for severe service, including high RPM
operation
3121202
Torque Value Interval
(Dry) Hours
190 ft. lbs. 50/600*
(258 Nm)
See Note
190 ft. lbs. 50/600*
(258 Nm)
See Note
15 ft. lbs (20 Nm) 150
170 ft. lbs (231 Nm) 150
165 ft. lbs. (231 Nm) A/R
30 ft. lbs. (42 Nm) A/R
Use SAE Viscosity Number
*10W
*10W
*10W
20W-20
30
40
When Outside
Temperature is
Consistently
Below +10°F. (+12°C.)
Below +60°F. (+16°C.)
-10°F. to +90°F. (-23°C. to
+32°C.)
Above -10°F. (-23°C.)
Above +20°F. (+7°C.)
*Not recommended for severe service, including high RPM oper-
ation
NOTE: Crankcase oil must be high quality detergent type
meeting API service classification SF, SH, SG.

Deutz Engine Oil Specifications

Single Viscosity Oil (CD-SE, CD-SF)
When Outside Temperature is
Consistently
-20°F. to +25°F. (-29°C. to +4°C.)
+5°F. to +50°F. (+15°C. to +10°C.)
+40°F. to +85°F. (+4°C. to +30°C.)
Above 75°F. (24°C.)
Multi Viscosity Oil (CD-SE, CD-SF)
*This viscosity can be used at colder temperatures with
engine oil preheating.
When Outside Temperature is
Consistently
-40°F. to +75°F. (-40°C. to +24°C.)
-15°F. to +70°F. (-26°C. to +21°C.)
-15°F. to +85°F. (-26°C. to +30°C.)
Above -5°F. (-21°C.)
-5°F. to +75°F. (-21°C. to +24°C.)
*This viscosity can be used at colder temperatures with engine oil pre-
heating.
NOTE: Crankcase oil should be MIL-L2104B/MIL-L2104C
or have properties of API classification CC/CD
grades.
– JLG Lift –
SECTION 1 - SPECIFICATIONS
Use SAE Viscosity Number
*5W-20
5W-30
10W-30
10W-40 or 10W-50
20W-40 or 20W-50
Use SAE Viscosity
Number
*10W
20W-20
30
40
Use SAE Viscosity Number
*5W-30 (Synthetic)
10W-30
10W-40
15W-40
15W-30
1-5