Stanford Research Systems SIM918 Operating And Service Manual page 65

Appendix A Index
STATUS signal, 1 – 3, 1 – 10, 3 – 16, 17, 3 – 25
break signal, see Device Clear
Accuracy
gain, see Gain, accuracy
o set, 2 – 6
Autocalibration, 1 – 3, 2 – 6, 7, 3 – 14, 15, 3 –
18, 3 – 22, 3 – 26
Autozero, ix, 1 – 2, 3, 1 – 5, 2 – 6, 2 – 8, 3 – 14,
15
button, see Button, [AUTOZERO]
clock source, see Reference clock, source
LED, see LED, AUTOZERO
phase, 3 – 14
selecting, ix, 1 – 2, 3, 1 – 9, 2 – 6, 3 – 6, 3 –
13, 14, 3 – 19
switching frequency, ix, 1 – 2, 1 – 6
Autozero circuit, 1 – 3, 1 – 5, 6, 1 – 8, 2 – 2, 2 –
5, 6, 2 – 8, 3 – 15
settling time, 2 – 5, 2 – 8
Bandwidth
bias, viii, 2 – 4
current, viii, 2 – 2, 3
Baud rate, 1 – 12, 3 – 6
Bias, iii, 2 – 4
bandwidth, see Bandwidth, bias
button, see Button, [BIAS GND]
connector, iii, viii, 1 – 7, 8, 2 – 7, 3 – 15
shield, viii, 1 – 3, 1 – 7–9, 2 – 4, 3 – 6, 3
– 12, 3 – 19
input resistance, viii, 2 – 4
LED, see LED, BIAS GND
overload, see Overload, bias
selecting, viii, 1 – 3, 1 – 7, 1 – 9, 2 – 5, 3 –
6, 3 – 12, 3 – 19
shield
button, see Button, [BIAS Shield]
LED, see LED, BIAS Shield
voltage, iii, 1 – 2–4, 1 – 7, 8, 2 – 4, 5, 3 – 15
limits, viii, ix, 1 – 7, 2 – 4, 5
voltage bu er, 1 – 7, 2 – 4
o set voltage, 1 – 7, 2 – 4
Block diagram, 1 – 4
BNC, iii, viii, ix, 1 – 3, 1 – 7, 8, 2 – 3, 4, 2 – 7, 3
– 12, 3 – 15
Bu er
bias, see Bias, voltage bu er
input, 3 – 6, 3 – 25–27
overflow, 3 – 6, 7, 3 – 27
output, see Output queue
voltage, see Output, voltage bu er
Button, 1 – 9, 3 – 18, 3 – 26
[AUTOZERO], 1 – 5, 3 – 18
[BIAS GND], 1 – 7, 2 – 5, 3 – 18
[BIAS Shield], 1 – 7, 3 – 18
[GAIN], 1 – 5, 2 – 7, 3 – 18
[INPUT Open], 1 – 6, 3 – 18
[INPUT Shield], 1 – 7, 3 – 18
[Output 1 pps sync], 1 – 6, 3 – 18
Circuit schematics, see Schematic diagrams
Clock stopping, 1 – 3, 2 – 7, 3 – 11, 3 – 19
Command
error, 3 – 21, 3 – 26
parameters, 3 – 7, 3 – 21
separator, 3 – 7
terminator, 3 – 6, 7, 3 – 20, 3 – 22
Common-mode rejection (CMRR), ix, 1 – 7, 2
– 4
Compensation, 2 – 3
Console mode, 3 – 6, 7, 3 – 20
Current gain, see Gain
Current input, see Input
DB–15, 1 – 10, 11, 2 – 4
DB–9
female, 1 – 11
male, 1 – 11
Default configuration, see Reset
Device Clear, 3 – 7, 3 – 20, 3 – 22, 3 – 27
Device error, 1 – 6, 3 – 21, 3 – 26
A – 1