Hide unknown ﬁle
Select "Hide unknown ﬁle" in the utility menu and press the
[F8] key. A check mark will appear at the left of "Hide
unknown ﬁle." With this setting, undeﬁned ﬁles will not be
displayed in the directory window. However, this is effec-
tive only if the current directory is a DOS directory.
Select "Translation" in the utility menu and press the [F8]
key. A check mark will appear at the left of "Translation."
With this setting, .KMP (Korg multisample parameter) ﬁles
and .KSF (Korg sample ﬁle) DOS ﬁle names will be dis-
played as the multisample name or sample name used in
Sampling mode (if the EXB-SMPL option is installed).
This command loads into internal memory the ﬁle or direc-
tory that was selected in the "directory window" (1.1–1b).
When you choose "Load selected" from the Utility menu, a
dialog box will appear. The dialog box will differ depending
on the type of ﬁle to be loaded.
If the ﬁle to load cannot be found, or when loading a
ﬁle that was saved in parts
When loading multisample or sample data ﬁles (if sample
data RAM is installed), and the TRITON Le cannot ﬁnd a
necessary ﬁle in the current directory or in a lower directory,
a dialog box like the one shown below ("Where is a ...") will
be displayed. This will appear in the following situations.
• When loading a .KSC file (when sample data RAM is
installed), if the .KMP file used by it cannot be found
• When loading a .KMP file (when sample data RAM is
installed), if the .KSF file cannot be found
• When loading an AKAI S1000/S3000 format Program
file (when sample data RAM is installed), if the Sample
file cannot be found
• When loading a .KSF file (when sample data RAM is
installed) that is larger than the capacity of the media
and was saved across multiple volumes of media, when
the first volume has finished loading and the second or
subsequent volume is needed
If this dialog box appears, take the following action.
1 Select the directory that contains the ﬁle requested by
"Where is a ..." If the requested ﬁle is on another volume
of media, exchange the media, then press the [MEDIA]
key or a function key to make the TRITON Le recognize
the media, and then select the directory.
It is not possible to open .PCG or .SNG ﬁles in the
"Where is a ..." dialog box. The [F6] ("OPEN") key can-
not be used for .PCG or .SNG ﬁles.
2 Press the [F8] ("Select") key to resume loading. If you
press the [F7] ("Cancel") key, loading will be halted. If
you press the [F3] ("Skip") key, the speciﬁed ﬁles will be
skipped, and the next ﬁle will be loaded.
Except for special cases in which the media containing
the speciﬁed ﬁle has been damaged or is unavailable,
press the [F8] ("Select") key to continue loading.
1) Load .PCG:
All data in the .PCG ﬁle will be loaded.
1 If the current directory contains a .SNG ﬁle or .KSC ﬁle of
the same ﬁlename, you can select "Load ********.SNG
too" and "Load ********.KSC too".
• If you check "Load ******.SNG too," the file with an
identical name to the .PCG file and an extension of .SNG
will also be loaded.
• If you check "Load ******** .KSC too," the file with an
identical name to the .PCG file and an extension of .KSC
will also be loaded.
2 If you checked "Load ********.KSC too", set ".KSC Alloca-
tion" to specify how the multisamples and samples
within the .KSC ﬁle will be loaded.
Append: The data will be loaded into the numbers after
the last multisample or sample number currently existing
in sample data RAM (i.e., that were previously sampled
or loaded). In this case, only the valid multisamples and
samples will be loaded, and will be packed without leav-
ing vacant numbers (see diagram below).
At this time, programs in the .PCG ﬁle that use multisam-
ples listed in the .KSC ﬁle will automatically have their
oscillator multisample settings remapped so that each
program uses the correct multisamples. Drum kits in the
.PCG ﬁle that uses samples listed in the .KSC ﬁle will also
have their drum kit sample settings remapped so that the
drum kit plays the correct samples.
Clear: All multisamples and samples currently existing
in sample data RAM will be cleared, and the multisam-
ples and samples will be loaded in the same conﬁgura-
tion as when they were saved (see diagram below).
If you want to load multisamples and samples from
media without erasing the multisamples and samples
that currently exist in sample data RAM, choose
If you want to reproduce the state in which the data had
been saved, for example immediately after power-on,
.KSC file to be loaded
Internal memory before
3 To load the data, press the [F8] ("OK") key. To cancel
without loading, press the [F7] ("Cancel") key.
Internal memory after