Korg TRITON Le Electric Keyboard Parameter Manual: Prog 4.2: Ed–filter2; Basic; Mod.1 (filter2 Modulation1); Mod.2 (filter2 Modulation2)

Korg electric keyboard parameter guide.
Hide thumbs


R (AMS1 SW Release)
Specifies the direction in which "AMS1 (Time Mod. AMS1)"
will affect the release time. With positive (+) values of "I
(AMS1 Intensity)," setting this parameter to + will allow
AMS1 to lengthen the time, and setting this parameter to –
will allow AMS1 to shorten the time. With a setting of 0
there will be no change.
Filter 1 EG changes (Time) (AMS = Velocity, Intensity = a positive (+) value)
Softly played note with "A,"
Strongly played note with
"D," "S" and "R" set to +
"A," "D," "S" and "R" set to +
(setting of 4.1–5a: Filter 1 EG)
AMS2 (Time Mod. AMS2)
I (AMS2 Intensity)
A (AMS2 SW Attack)
D (AMS2 SW Decay)
S (AMS2 SW Slope)
R (AMS2 SW Release)
These parameters are the settings for "AMS2" to control the
"Time" parameters of the filter 1 EG ( "AMS1 (Time Moc.
AMS1)"–"R (AMS1 SW Release)").
4.1–5d: UTILITY
"Write Program" (1.1–1c), "Copy Oscillator," "Swap
Oscillator" (2.1–1d)
For details on how to select the desired utility function, refer
to "PROG 1.1–1c: UTILITY."
Sync Both EGs
If you select "Sync Both EGs" from the Utility menu and
press the [F8] key, a check mark will appear at the left of
"Sync Both EGs." In this state, the filter 1 EG and the filter 2
EG can be edited simultaneously. (Editing either one will
cause the other to change.)
"Sync Both EGs" cannot sync the filter EG and amp EG
independently. For example if you sync in 5.1–3d, it will
be synced here as well.
This can be selected only if "Mode (Oscillator Mode)"
(2.1–1a) is Double.
[–, 0, +]
Strongly played note with
"A," "D," "S" and "R" set to –
[Off, (KT, EXT)]
[–, 0, +]
[–, 0, +]
[–, 0, +]
[–, 0, +]
PROG 4.2: Ed–Filter2
4.2–1: Basic
4.2–2: Mod.1
(Filter2 Modulation1)
4.2–3: Mod.2
(Filter2 Modulation2)
4.2–4: lfoMod
(LFO Modulation)
4.2–5: EG
(Filter2 EG)
Indicates settings for filter 2, which controls the tone of oscil-
lator 2. You can select either a 24 dB/oct low pass filter with
resonance, or a 12 dB/oct low pass filter and 12 dB/oct high
pass filter connected in series. Filter 2 can be used when
"Mode (Oscillator Mode)" (2.1–1a) is Double. ( "PROG 4.1:
Ed-Filter 1")
PROG 5.1: Ed–Amp1
Indicates settings for amp 1 which controls the volume of
oscillator 1. Pan settings are also made here.
5.1–1: Lvl/Pan
These parameters control the volume and pan of oscillator 1.
5.1–1a: Amp1 Level
Level (Amp1 Level)
Sets the volume of oscillator 1.
The volume of a program can be controlled by CC#7
(volume) and CC#11 (expression). The resulting level is
determined by summing the values of CC#7 and
CC#11. The Global MIDI channel "MIDI Channel"
(GLOBAL 2.1–1a) is used for control.
5.1–1b: Pan
Pan (Amp1 Pan)
[Random, L001...C064...R127]
Sets the pan (stereo location) of oscillator 1.
A setting of L001 places the sound at far left, C064 in the
center, and R127 to far right.
Random: The sound will be heard from a different location
at each note-on.
This can be controlled by CC#10 (panpot). A CC#10
value of 0 or 1 will place the sound at the far left, a
value of 64 will place the sound at the location specified
by the "Pan" setting for each oscillator, and a value of
127 will place the sound at the far right. This is con-
trolled on the global MIDI channel "MIDI Channel"
(GLOBAL 2.1–1a).


   Also See for Korg TRITON Le Electric Keyboard

   Related Manuals for Korg TRITON Le Electric Keyboard

Comments to this Manuals

Symbols: 0
Latest comments: