Yamaha 2012 TMAX XP500A Service Manual page 75

Item
Front wheel sensor bolt
Rear wheel sensor bolt
Rear brake lock caliper bolt
Rear brake lock caliper slide pin
bolt
Rear brake lock caliper bracket
bolt
Rear brake lock caliper piston
locknut
Rear brake lock adjusting nut
Front brake hose joint nut
Front brake hose holder bolt
Rear brake hose guide bolt
Rear brake hose holder bolt
Rear brake lock cable holder bolt
Rear brake hose holder bolt (rear
left footrest)
Front wheel sensor rotor bolt
Rear wheel sensor rotor bolt
Centerstand bracket nut
Centerstand nut
Sidestand nut
Rear footrest bracket bolt
Lean angle sensor bolt
Starter relay lead bolt
Sidestand switch nut
Intake air pressure sensor bolt
Ambient temperature sensor bolt
Throttle position sensor screw
ECU (engine control unit) nut
Hydraulic unit assembly bracket
bolt
Hydraulic unit assembly and
hydraulic unit assembly bracket
bolt
Brake hose flare nut
Damper mount bolt nut
Brake joint assembly bolt
Damper cap bolt
TIP
Lower ring nut
1. First, tighten the lower ring nut approximately 52 Nm (5.2 m·kgf, 38 ft·lbf) by using the ring nut
wrench and turn the steering right and left a few times, then loosen the lower ring nut completely.
2. Retighten the lower ring nut 14 Nm (1.4 m·kgf, 10 ft·lbf).
Thread
Q'ty
size
M6 1 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
M6 1 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
M8 2 23 Nm (2.3 m·kgf, 17 ft·lbf)
M8 1 17 Nm (1.7 m·kgf, 12 ft·lbf)
M8 1 22 Nm (2.2 m·kgf, 16 ft·lbf)
M16 1 22 Nm (2.2 m·kgf, 16 ft·lbf)
M8 1 15 Nm (1.5 m·kgf, 11 ft·lbf)
M6 1 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
M6 2 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
M6 1 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
M6 4 10 Nm (1.0 m·kgf, 7.2 ft·lbf)
M6 1 10 Nm (1.0 m·kgf, 7.2 ft·lbf)
M6 1 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
M5 3 8 Nm (0.8 m·kgf, 5.8 ft·lbf)
M5 5 8 Nm (0.8 m·kgf, 5.8 ft·lbf)
M10 4 55 Nm (5.5 m·kgf, 40 ft·lbf)
M10 2 55 Nm (5.5 m·kgf, 40 ft·lbf)
M10 1 65 Nm (6.5 m·kgf, 47 ft·lbf)
M8 4 30 Nm (3.0 m·kgf, 22 ft·lbf)
M4 2 1.5 Nm (0.15 m·kgf, 1.1 ft·lbf)
M6 2 3.6 Nm (0.36 m·kgf, 2.6 ft·lbf)
M5 2 3.8 Nm (0.38 m·kgf, 2.8 ft·lbf)
M5 1 3.8 Nm (0.38 m·kgf, 2.8 ft·lbf)
M5 1 3.8 Nm (0.38 m·kgf, 2.8 ft·lbf)
M5 2 3.5 Nm (0.35 m·kgf, 2.5 ft·lbf)
M6 2 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
M8 2 16 Nm (1.6 m·kgf, 12 ft·lbf)
M6 3 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
M10 4 16 Nm (1.6 m·kgf, 12 ft·lbf)
M8 3 16 Nm (1.6 m·kgf, 12 ft·lbf)
M6 2 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
M6 3 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
2-20
TIGHTENING TORQUES
Tightening torque Remarks
Left-hand
thread.
LT
LT