General Vent Installation Information; Installation Of Side Wall Venting - Kingsman HBZDV3624 Installation Instructions Manual

“zero clearance” direct vent gas fireplace

Installation instructions manual (47 pages)

Table of Contents

This gas appliance is approved to be vented either through the side wall or vertically through the roof. Only Kingsman Flex(Z-Flex)Venting Kits and

components specifically approved and LABELED for this stove may be used. This appliance is also approved for use with Simpson-Duravent Direct

Vent system (Model DV-GS Series), Ameri-Vent Direct Vent Pipe System, ICC Excel Direct, Metal Fab Sure-Seal DV and Selkirk Direct Temp.

Simpson Dur a-Vent for Masonr y Chimney Conver sion Kits may be used with this appliance Use your existing masonry chimney and route

the exhaust gases intake air through the side of the masonry chimney. Use Simpson Dura-Vent kit numbers 46DVA-KMC or 46DVA-KCT.

Termination Cap, Kingsman/Dura-Vent adapter, and 4" flex are sold separately.

Simpson Dur a-Vent for Factor y built metal Chimney Conver sion Kits may be used with this appliance. Use your existing through the ceil-

ing, wood stove chimney and route the exhaust gases and intake air through the existing wood burning metal chimney. Use Simpson Dura-Vent

Kit numbers 46DVA-KCA for 6 5/8" to 8 5/8" OD sized chimney, 46DV-KCB for 8 3/4" to 10 1/2" OD sized chimneys and 46DVA-KCC for

10 5/8" to 13" OD sized chimneys. Kits 931, 932, and 933 include a cap adapter and Retro Connector. Termination Cap, Kingsman/Dura-Vent

adapter, and 4" flex are sold separately.

RIGID OR HARD PIPE

When using Simpson Duravent, AmeriVent pipe, ICC Excel Direct, Metal Fab Sure-Seal

DV and or Selkirk Direct Temp a Duravent hardpipe adapter must be used (part # ZDVDFA

for fireplaces and part # ZDVDKA for Stoves, Serenity and ZDV3624B). Follow installa-

tion instructions provided by Simpson Duravent/AmeriVent/Selkirk Direct Temp, ICC Excel

Direct, Metal Fab Sure-Seal DV for installation of pipe and adhere to the clearance to com-

bustibles provided in this manual. Apply a bead of Mill Pac high temp sealant to all joints of

pipes, adapters and termination, when using Kingsman Flex(Z-Flex)Venting venting and

Simpson Duravent venting.

NOTE: Increase framing depth by one inch when using hardpipe.

WARNING: DO NOT mix parts from different systems unless stated in the manual.

Flex Pipe Venting

Kingsman Flex pipe is shipped in unexpanded length. When installing pipe expand the

lengths. Pipe can be expanded to twice their lengths e.g. 4ft. to 8ft. Fully expand pipe and

cut off excess.

Do not use more than 2 couplers to extend short pipes. Single sections are preferred in an

installation attaching at the fireplace and termination.

Place the spring spaces provided approximately every two feet to stabilize 4" flex in the cen-

ter of 7" flex. When forming bends place spring in bend or before and after. (See Fig. 1).

Horizontal runs require support metal straps every 2 feet. In off set installation support

straps should be used to stabilize pipe.

Expand 4" and 7" flex pipe to the point that the 7" protrudes approximately 2 to 3 inches past

outer wall and the 4" flex protrudes approximately 2 to 3 inches past the 7" flex. See Fig. 1.

Attach the 4" pipe to the termination first and secure with sealant and screws then attach the

7" flex to the termination with caulking and screws. Termination may then be moved back to

the outer wall and attached to home screwing into the framing. Silicone around termination to

waterproof. If siding shield is going to be used attach this using same attaching hole as the top

of termination after termination has been caulked for water proofing.

Use Hi Temp Sealant

Apply a bead of mill pac high temp sealant to all joints and use four screws to secure each

pipe at fireplace, termination and any joint if joining any sections of pipe.

1. The minimum distance from the bottom of fireplace to centre of vent is 34 inch

(85 cm) (See Figure 1). Cut a hole through the wall allowing for a 11" x 11" (inside diameter) in com-

bustible walls for wall thimble or an 8" diameter hole in a non-combustible wall (See Figure 2).

2. Note clearance to combustible as stated on pages 7 & 8.

3. Select the approximate vent length, precise measurements are not needed as your flex pipe can be expand-

ed to twice its shipped length for ease of installation.

4. To install wall thimble centre over 11" x 11" (inch) framing from both sides of wall and secure. Route

flex vent pipe through wall thimble (See Figure 1).

5. Before joining pipes, apply a bead of high temperature sealant (Mill Pac) to end of pipe. First attach the

four inch (4") flue pipe to the vent termination with sealant, and secure with the four screws provided. At

this time make sure the spacer springs are attached to the (4") flex pipe as required. Then attach the seven

inch (7") pipe by the same method.

6. Mount vent termination and seal to wall using caulking around the wall thimble to weather proof. After

installing the vent termination, double check to make sure the pipe extends properly through wall thimble

and into vent termination.

7. Before joining pipes to fireplace flue, apply a bead of high temperature sealant (Mill Pac) to end of pipe.

First attach the four inch (4") flue pipe to fireplace with sealant, and secure with the four screws provid-

ed. At this time verify that the spacer springs are attached properly to the (4") flex pipe as required. Then

attach the seven inch (7") pipe by the same method.

8. Support horizontal pipes every two (2) feet (61 cm) with metal strap bands. Re-check fireplace to make

sure it is levelled and properly positioned and secured.

9. Support vertical pipes to maintain a minimum of 1" or greater clearance to combustibles with metal strap-

ping bands.

10. If finishing the outside wall with vinyl or wood siding it is recommended that a Siding Shield be installed,

Part Number ZDVSSLR.

Note: Vent Termination must not be recessed into wall or siding.