Reset Button - Altronix AL802ULADA Installation Manual

Alarm
Fig. 2
Control
Panel
(FACP)
Fire
Alarm
Control
Panel
(FACP)
unswitched 120VAC
power mains
(non-power limited)
line
ground
+
Green Lead
EOL
Resistor
Non-Supervised
from
FACP
--
EOL Power
Supervision Relay
(Not Supplied)
EOL
Resistor
+
from
FACP
SW2 SW1
--
+ OUT1 --
AL802ULADA
Optional Hookup Diagram:
Fire
unswitched 120VAC
power mains
(non-power limited)
unswitched 120VAC
power mains
(non-power limited)
line
ground
neutral
+
Green Lead
+
4-wire Smoke
Non-Supervised
Detector
--
4-wire Smoke
-- AUX +
Detector
--
AC Local BAT FAIL
NC C NO NC C NO NC C NO
+
4-wire Smoke
neutral
Detector
SW2 SW1
--
+ OUT1 --
Power-Limited Outputs
-- AUX + -- DC +
+
4-wire Smoke
Detector
RESET
--
Fig. 2c
+ OUT3 -- + OUT4 --
+ OUT2 --
EOL Power
Supervision Relay
(Not Supplied)
Power-Limited Outputs
2.5 amp per
output in alarm
(total= 8 amp)
(Supervised)
VR1
AC LED
VR1
AC Local BAT FAIL AC FAIL
NC C NO NC C NO NC C NO
line
ground
Use separate knockout.
Keep 1/4" spacing from
non power limited wiring
Green Lead
AC LED
-- DC +
OUT1 OUT3
INPUT SELECT
Non-Supervised
TEMPORAL
STROBE SYNC
IN > OUT SYNC
OUT2 OUT4
INPUT SELECT
TEMPORAL
AC FAIL
STROBE SYNC -- AUX +
RESET
IN > OUT SYNC
Use separate knockout.
Keep 1/4" spacing from
+ OUT2 -- + OUT3 -- + OUT4 --
non power limited wiring
IN1+ IN1-- IN2+ IN2-- C "DRY1" NC
RET1+ RET1-- RET2+ RET2--
Supervised Non-Supervised
2.5 amp per
output in alarm
OUT1 OUT3
INPUT SELECT
(total= 8 amp)
TEMPORAL
OUT1 OUT2 OUT3 OUT4
(Supervised) STROBE SYNC
IN > OUT SYNC
INP1 INP2
OUT2 OUT4
INPUT SELECT
TEMPORAL
SW2 SW1
STROBE SYNC
IN > OUT SYNC
+ OUT1 --
Trouble Memory

Reset Button

IN1+ IN1-- IN2+ IN2-- C "DRY1" NC
UPPER TERMINALS
RET1+ RET1-- RET2+ RET2-- C "DRY2" NC LOWER TERMINALS
Supervised Non-Supervised
Fig. 2a
AC Local
NC C NO
neutral
OUT1 OUT2 OUT3 OUT4
INP1 INP2
These circuits are used to
FAULT
monitor AC and Bat Fail and
-- DC +
will cause a simultaneous trouble
condition to the FACP's IN1 and IN2
Non-Supervised
Digital Communicator or
Local Annunciator Dry output Contact
(Form "C" contacts)
RESET
UPPER TERMINALS
C "DRY2" NC
LOWER TERMINALS
Addressable
Control Module These circuits are used to
FAULT Trigger Output
monitor AC and Bat Fail and
See Note 2
will cause a simultaneous trouble
+ OUT2 -- + OUT3 -- + OUT4 --
condition to the FACP's IN1 and IN2
Digital Communicator or
Power-Limited Outputs
Local Annunciator Dry output Contact
2.5 amp per
(Form "C" contacts)
output in alarm
(total= 8 amp)
(Supervised)
Addressable
Control Module
Trigger Output
See Note 2
AC LED
BAT FAIL AC FAIL
NC C NO NC C NO
Use separate knock
Keep 1/4" spacing
non power limited w
OUT1 OUT3
INPUT SELECT
TEMPORAL
OUT1 OUT2 OUT3 OU
STROBE SYNC
IN > OUT SYNC
OUT2 OUT4
INPUT SELECT
TEMPORAL
STROBE SYNC
IN > OUT SYNC
Common trouble
Input/Output
Fig. 2b
Non-Supervised
IN1+ IN1-- IN2+ IN2-- C "DRY1" NC
RET1+ RET1-- RET2+ RET2-- C "DRY2" NC
Supervised Non-Supe
INP1 INP2
UPPER TER
LOWER TER
- 7 -